Latest RF & Microwave Products of the Week (3

Multi-Die Fully-Integrated Front End Module from 8 to 12 GHz

The QPF5010 from Qorvo is a Multi-Die Fully-Integrated Front End Module that operates from 8 to 12 GHz for X-Band Radar Applications. It uses the best-in-class GaN and GaAs solutions for the four functional blocks - T/R switch, power amplifier, low-noise amplifier, and limiter. It delivers up to 10 Watts of saturated RF transmit power with a PAE of 30-40%. On the Rx side, it provides a gain of 25 dB with a noise figure of 2.2 dB. The QPF5010 provides high-performance in a compact size to make design, layout, assembly, and test easier to achieve, allowing for shorter design cycles and faster time to market. This FEM is available in a land grid array (LGA) package that measures 7 x 5 mm and is ideally suited for communications and commercial/military X-band radar applications. Click here to view specs.

Broadband Pick-off Tee from DC to 67 GHz

The HL9467 from Hyperlabs is a Broadband Pick-off Tee that operates from DC to 67 GHz on the thru line and has a 55 GHz bandwidth (-3 dB) on the pick-off line. It is suitable as a trigger source with minimum perturbation of the thru signal path. The Pick-off tee has a thru insertion loss of 4 dB, a pick-off insertion loss of 10 dB, and can handle an input power of up to 30 dBm. The device has an amplitude match of ± 0.25 dB and a phase match of ± 2° at 10 GHz. This RoHS-compliant pick-off tee is available in a module that measures 30.75 x 24.23 x 13.59 mm with 1.85 mm jack connectors. It is ideal for digital oscilloscope applications including pre-scaler triggering, synchronization, and clock/data recovery. Click here to view specs.

100 W GaN HEMT Transistor from 5.3 to 5.8 GHz

The WP485P55100MH from WAVEPIA is a Matched GaN HEMT that operates from 5.3 to 5.8 GHz. It provides a saturated output power of 100 W with a small signal gain of 9.6 dB and has an efficiency of 41.3% @ 5.5 GHz. This transistor requires a 48 V DC supply. It is available in a 680MH surface-mount package that measures 24.0 x 21.2 x 1.3 mm and is ideal for point to point / multipoint radios, test equipment & industrial controls, SATCOM, military end-use, and C-band radar applications. Click here to view specs.

4.3-10 Type Surge Protector from 698 to 3800 MHz

The 766440-DS from Spinner is an RF Surge Protector that operates from 698 to 3800 MHz. It has an average power rating of 850 W @ 698 MHz and can handle surge currents of up to 20 kA. The surge protector has an insertion loss of less than 0.1 dB and a VSWR of under 1.4:1. It includes a quarter wavelength stub and DC break. This IP67-rated protector is available in a module that measures 129.5 mm (L) x 38.0 mm (dia.) with a 4.3-10 connector interface. Click here to view specs.

Bluetooth 5.2 Low Energy Module from 2402 to 2480 MHz

The EYSNSNZWW from Taiyo Yuden is a Bluetooth 5.2 Low Energy Module. It has an ARM® Cortex M4 32-bit processor and features 24 KB of RAM and 192 KB of flash memory. The module provides a typical output power of +4 dBm and requires a supply voltage from 1.7 to 3.6 V. The module is available in an SMD package that measures 3.25 x 8.55 x 1.00 mm and has an integrated high-performance pattern antenna. It is ideal for a wide range of Bluetooth low power applications. Click here to view specs.

Bluetooth 5.2 + 802.15.4 + NFC Modules

The BL5340 Series from Laird Connectivity are multi-core Bluetooth 5.2 + 802.15.4 (Thread and Zigbee) + NFC Modules. These small, robust modules are available in two variants: main module (BL5340 with nRF5340) or power amplified variant (BL5340PA with nRF5340 + nRF21540). The modules feature dual core Arm® Cortex M33 microcontrollers which can run a low power core focused purely on wireless connectivity, with a second higher performance core targeted for end applications. They include ARM CryptoCell-312 including trusted execution, root-of-trust, and secure key storage security features. The modules are available with integrated pre-certified PCB or trace pad antenna options. The modules feature Bluetooth 5.2 including Isochronous Channels and LE Audio which adds support for next generation Bluetooth audio for stereo streaming and broadcast audio. These modules are suitable for use in applications such as smart building, asset tracking, secure medical peripherals, and industria...Click here to view specs.

Intelligent RF Spectrum Recorder from 16 kHz to 14/26.5 GHz

The ODEN 3001 from Novatar Solutions is an Intelligent RF Spectrum Recorder with a frequency range from 16 kHz to 14/26.5 GHz and a real-time bandwidth of 765 MHz. It automatically captures individual interfering signals or rare and unknown events of interest for analysis and spectrum characterization which reduces the amount of data to be recorded thereby simplifying data handling and reducing associated costs. The operator can also control how much data in the time and frequency domain are recorded when trigger conditions are met. The ODEN 3001 combines a frequency mask trigger (FMT), 1024 individual digital downconverters (DDC) with acquisition regions and rules to record all channels simultaneously into separate files. The user-friendly GUI ensures intuitive configuration and monitoring of the recording process. The system has a real-time spectrum monitor with spectrum & spectrogram views. All recorded signals are stored in separate data files and a list view makes it easy ...Click here to view specs.

High Power RF Source for TACAN, DME & IFF Equipment

The Model 1414-2500 from TSL is a high power, flexible solid-state RF source that operates from 960 MHz to 1215 MHz. This high power source has been developed for specific requirements in avionics testing that include TACAN (Tactical Air Navigation System), DME (Distance Measuring Equipment) & IFF (Identification Friend or Foe). It can generate an output power up to 64 dBm (2.5 KW). When operated in the TACAN mode, it produces a Gaussian-type RF waveform (or other waveform specified by the user) in accordance with MIL-STD-291 covering the frequency range of 960 MHz to 1215 MHz. When operated in the IFF mode, the unit generates 2 or 4 pulses at 1030/1090 MHz depending on the mode of operation selected. A special SLS mode is provided with a maximum 23 dBm which produces 3 pulses with pulse P2 variable between -12 dB and +3 dB relative to pulse P1 and P3. The Signal Source is equipped with a large 7” display and user-friendly equipment that responds to commands enter...Click here to view specs.

SP5T Reflective PIN Diode Switch from 2 to 18 GHz

The SW-S200-5S from UMCC is an SP5T Reflective PIN Diode Switch that operates from 2 to 18 GHz with 3-Bit binary control and an integrated TTL driver. It has an insertion loss of less than 2.4 dB and provides more than 60 dB of isolation. The switch can handle up to 24 dBm of CW input power, 10 W of peak power and has a switching speed of less than 60 ns. It requires a supply voltage of -12 / +5 V and follows MIL-STD-202F constructional standards. The SW-S200-5S is available in a module that measures 38.1 x 38.1 x 10.2 mm with SMA Female connectors. Click here to view specs.

0.25 W Low Noise Amplifier from 6 to 18 GHz

The LNA1019A-1 from Exodus Advanced Communications is a Low Noise Amplifier that operates from 6 to 18 GHz. This amplifier provides 24 dBm of output power with a linear gain of more than 60 dB and has a noise figure of less than 7.5 dB. It operates over a DC supply of 12 V and consumes less than 800 mA of current. The amplifier has a compact Class A linear design for optimum reliability & ruggedness for a wide range of applications. It is available in a module that measures 53.25 x 17 x 8.35 mm with SMA female connectors. Click here to view specs.

C-Band Low Noise Amplifier from 4.4 to 5 GHz

The APT4-04400500-0715-D4-GW from AmpliTech is a C-band Low Noise Amplifier that operates from 4.4 to 5 GHz. It provides an output power of 16 dBm and gain of 35 dB with a noise figure of 0.6 dB. The amplifier requires a supply of 12 Vdc while consuming up to 16 dBm of power. It is available in a module with SMA male/female connectors and is ideal for SATCOM, radar, microwave radio systems and telemetry applications. The LNA has a Bias Thru Output (BTO) option to provide the DC power via the center conductor of the output connector allowing for mast antenna mounting as well as an option to provide power via an industry standard SMA connector. The specific Gain Window and superb flatness make this amplifier a reliable staple component for self-contained communications systems deployed on various sea-based stations miles from land, making reliable communications an absolute necessity. Click here to view specs.

Compact USB VNA from 9 kHz to 6.5 GHz

The S5065 is a compact 2 port VNA that operates up to 6.5 GHz. It can be controlled using a software application which runs on a Windows PC, laptop, or tablet, connecting to the measurement hardware via USB interface. The application can be installed on multiple computers, making it easy to share the use of the analyzer measurement module. The S5065 can measure all four S parameters S11, S12, S21, S22 and provides a wide variety of analysis capabilities, including time-domain with gating and frequency offset modes, at no additional cost. Collection of metrology-grade S-parameter test results can be achieved manually or through automation in Python, MATLAB, Excel, C++, or LabVIEW. Click here to view specs.

10 MHz to 26 GHz Real-Time Phase Noise Analyzer

The HA7062D from Holzworth is a real time phase noise analysis system that operates from 10 MHz to 26 GHz (optional to 40 GHz). It provides measurement offsets from 0.1 Hz to 100 MHz. The HA7062D has a high speed digital processor for speed, but the proven accuracy and speed starts with the analog front end. A key component of the analog front end is a pair of Holzworth HSX Series RF Synthesizers as the test system’s internal LOs. These ultra low noise RF sources not only complement the dual core FFT engine to provide one of the most advanced phase noise analyzers available, but they are also made available to the user at the front panel’s LO Output ports. The HA7062D is available in a fully shielded, fan-less 1U chassis that completely eliminates ground loops and troublesome microphonics for uncompromised performance and repeatability. Click here to view specs.

Coaxial Inner-Outer DC Block from 0.01 to 18 GHz

The BLKD-183-S+ from Mini-Circuits is a Coaxial Inner-Outer DC Block that operates from 0.01 to 18 GHz. It has an insertion loss of 0.43 dB and can handle an input voltage of up to 200 V. The DC block is available as a rugged stainless steel connectorized module that measures 0.5 inches in diameter and 1.3 inches in length with SMA-Male and Female connectors. It is ideal for Ku-band, and test & measurement applications. Click here to view specs.

SMPM (F) to SMA (M) 12 Inch Cable Assembly from DC to 18 GHz

The M55FS-78MS30245 from Taiwan Rapidtek Inc is a Magnetic SMPM (F) to SMA (M) Cable Assembly that operates from DC to 18 GHz. It has an insertion loss of less than 4.6 dB and has a VSWR of less than 1.4:1. The cable assembly measures 12 inches and has a bend radius of 12.7 mm with an SMPM Female connector on one side and an SMA Male connector on the other side. Click here to view specs.

Ultra-Low Loss Cable from 0.3 to 67 GHz

The Phase3 from MegaPhase is ultra-low loss cables that operate up to 67 GHz. These cables are optimized for consistent and repeatable performance where the demand is minimum attenuation, high shielding effectiveness, and low VSWR. They can be used to make cable assemblies with 1 mm, 1.85 mm, 2.4 mm, 2.9 mm, 3.5 mm, Type-N, TNC and SMA connectors. The Phase3 cables are available with phase matching, armoring, and in long lengths upon request. Click here to view specs.

10 MHz High-Stability, Laser-Based Rubidium Oscillator

The ICPT-1 from IQD is a High Stability 10 MHz Rubidium Oscillator. It is designed using the Coherent Population Trap method to obtain an excellent frequency stability of ±0.05 ppb and offers tight tolerance. This oscillator uses a laser to induce quantum transitions which results in a much lower power consumption of up to 2 W along with longer life expectancy. Users have the option to connect either an external 1 PPS input or take the internal clock for a 1 PPS output for synchronization in various applications. The 1PPS signal and frequency adjustment can be controlled via RS-232 data communication interface. The ICPT-1 is available in a 9-pin through-hole metal case that measures 36 x 45 x 14.5 mm and is ideal for synchronization or as a reference clock in satellite & secure communications, navigation systems, and in financial, utility, security, and communications timing applications. Click here to view specs.

30 dB Directional Coupler from 0.5 to 8 GHz

The 158030 from Krytar is a Directional Coupler that operates from 0.5 to 8 GHz. It is uniquely designed for system applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. The coupler has a coupling factor of 30 dB (±0.8 dB coupling deviation) with directivity of over 16 dB and an insertion loss of less than 0.8 dB. It can handle 20 W of average power, 3 kW of peak power, and has a VSWR of less than 1.35:1. The coupler is available in a module that measures 5.25 x 0.53 x 0.72 inches with standard SMA female connectors. It is ideal for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beamforming, and EMC testing environments. Click here to view specs.

20 dB Directional Coupler from 2 to 40 GHz

The VDC-20400A20 from VidaRF is a directional coupler that operates from 2 to 40 GHz. The coupler has a coupling value of 20 dB with directivity of over 12 dB and an insertion loss of less than 1.6 dB. It can handle up to 20 watts of input power and is available in a module with 2.92 mm female connectors. Click here to view specs.

Stand Alone RF Tunnel Shielded Box from 20 MHz to 40 GHz

The HDRF-3590 from RF Electronics is a Stand Alone RF Tunnel Shielded Box that operates from 20 MHz to 40 GHz. This fully portable design is equipped with caster wheels for ease of movement. The interior of this enclosure measures 650 (W) X 650 (H) X 2050 (L) mm. It has a thick RF absorbing foam that provides isolation of more than 120 dB @ 3 GHz. The box has shielded power filters which can be used to power devices placed inside the enclosure while blocking all wireless signals. The HDRF-3590 has a number of user-friendly I/O connection options that include HDMI, RJ45, USB, DB9, VGA, DB25 and AC/DC. It is ideal for 802.11 a/b/g/n/ac, Bluetooth, RFID and 3G Device Testing. Click here to view specs.

Low-Power RF Synthesizer from 49 to 2040 GHz

The CMX940 from CML Microcircuits is a low-power, high-performance Fractional-N PLL based RF Synthesizer. It has a fully integrated wideband VCO and a programmable output divider that generates signals from 49 to 2040 MHz. The synthesizer has two level-controlled single-ended RF outputs to support Tx and Rx sub-systems. A configurable reference path can be used to minimize close-in phase noise and mitigate integer and fractional boundary spurious. The synthesizer operates over a supply voltage from 3.0 to 3.6 V. It requires only an external loop filter and clock reference to provide a complete and very compact RF synthesizer solution. The chip configuration is controlled by an SPI-compatible C-BUS serial interface. It is available in a highly integrated LGA-48 package that measures 7 x 7 mm, reducing component count and PCB board area and is suitable for applications such as PMR/LMR, wireless data modem, general-purpose RF and IF, and marine radio. The low operating voltage and lo...Click here to view specs.

10.5 GHz Fixed Frequency Synthesizer

The LT-10500-03 from EM Research is a Fixed Frequency Synthesizer that generates an output signal at 10,500 MHz using an external 10 MHz reference. The generated signal has an output power of 3 dBm with spurious levels of less than -60 dBc, harmonics of lower than -20 dBc, and phase noise of under -110 dBc/Hz at 100 kHz offset. The synthesizer requires a DC supply voltage of 5 V and consumes 175 mA of current (typical). It is available in a module with extreme shock and vibration tolerance that measures 1.3 x 1.1 x 0.4 inches with removable SMA connectors for surface mount-ability and is suitable for SATCOM, ECM, Unmanned Aerial Vehicles (UAVs), and other airborne applications. Click here to view specs.

Detector Log Video Amplifier (DLVA) from 2 to 18 GHz

The STDLVA-90001 from Crane Aerospace and Electronics is a Detector Log Video Amplifier (DLVA) that operates from 2 to 18 GHz. It features a dual detector amplified design with a unique amplification and summing technique. The amplifier has an operating dynamic range from -67 to +5 dBm with a linearity of up to ± 1.5 dB and a maximum tangential signal sensitivity (TSS) of -67 dBm. It has a nominal slope of 75 mV/dB which is adjustable, a rise time of 35 ns and a fall time of 400 ns. The amplifier is fully temperature compensated for superior performance. The STDLVA-90001 is available in a fully hermetically sealed enclosure that measures 4.60 x 2.90 x 1.12 inches with SMA-female connector. It operates over a DC supply of +15/-15 V while consuming up to 200 mA of current. Click here to view specs.

High-Speed Reflective SP4T Switch from 1 to 18 GHz

The E9140H from Kratos is a Reflective SP4T Switch that operates from 1 to 18 GHz. It provides an insertion loss of less than 2.8 dB and an isolation of 60 dB. This switch can handle an input power of up to 200 mW and has a VSWR of less than 2:1. It has a rise/fall time of 10 nsec and supports TTL control interface. The switch requires a DC supply of +5/-12 V and consumes up to 135 mA of current. It is available in an economical hermetically sealed package with SMA Male connectors. Click here to view specs.

Low-Profile Screw Mount Antenna for 5G and GNSS Applications

The 2J6984BGFa from 2J Antenna is a Low Profile Screw Mount Antenna that operates from 617-960 MHz, 1427-2690 MHz, 1575-1606 MHz, 3300-5000 MHz, and 5150-5925 MHz. It has 3 ports – 2 Ports for 5G-NR/4G/3G/2G/CDMA MIMO bands and 1 port for GPS/GLONASS/QZSS/Galileo/L1 standards. This linear/right hand circularly polarized antenna has an omnidirectional / hemispherical radiation pattern. The GNSS Antenna has an integrated SAW pre-filter and an LNA that provides a gain of 28 dB (@ 2.7 V). It is available in an IP67/69 rated enclosure that measures 80 x 76 x 25.6 mm and has 300 cm cables with SMA male connectors. Click here to view specs.

Bandpass Filter

Lowpass Filter

Highpass Filter

Band Reject Filter

Diplexer

Triplexer

Flexible

Attenuators

Bends

Circulators

Directional Couplers

Isolators

Phase Shifter

Rotary Joints

Straights

Termination

Transitions

Waveguide to Coax Adapters

Rigid PCB Quotes

Flexible PCB Quotes

PCB Assembly Quotes

PCB Design Quotes

PCB Repair Quotes

PCB Stencil Quotes

Latest RF & Microwave Products of the Week (3 - 9 Dec, 2020)