Latest RF & Microwave Products of the Week (1

Drop-in Isolators from 10 MHz to 26.5 GHz

The drop-in Isolators from UIY operate from 10 MHz to 26.5 GHz. They have an insertion loss of less than 1.5 dB, isolation of over 14 dB, and can handle up to 500 watts of forward power. These isolators are available in a module with TAB connectors as standard products and can also be ordered as a custom module. They are suitable for Military, Space & Commercial applications. Click here to view specs.

9 kHz to 3/6 GHz Vector Signal Generator for IoT Applications

The N5166B CXG from Keysight is an RF Vector Signal Generator that operates from 9 kHz to 3/6 GHz with up to 120 MHz of RF modulation bandwidth covering most consumer wireless application testing requirements. It provides an output power of 18 dBm and has a phase noise of -119 dBc/Hz (20 kHz offset) at 1 GHz. This signal generator can be used to perform basic parametric testing of components and functional verification of receivers. It is available in a benchtop module that measures 88 x 426 x 489 mm, weighs 15.9 kg and is ideal for IoT, general-purpose R&D, and design validation (DVT) applications. Click here to view specs.

24 to 40 GHz Handheld Signal Generator

The J0SSAG14 from SAF Tehnika is a Handheld Signal Generator that operates from 24 to 40 GHz. It has an output power range of -3 to 5 dBm. This generator is ideal for carrying out different microwave system analysis and measurement applications like LOS Verification, Antenna alignment, etc. It has a touch screen intuitive interface that can be used even when wearing gloves. The signal generator is available in a handheld form factor that measures 130 x 81 x 28 mm. Click here to view specs.

0.4 to 2.7 GHz SP6T LTE Transmit/Receive Switch

The SKY13525-646LF from Skyworks is an SP6T antenna switch with a Mobile Industry Processor Interface (MIPI) controller. Operating from 0.4 to 2.7 GHz, it maintains a low insertion loss and high isolation, which makes it an ideal choice for UMTS, CDMA2000, EDGE, and LTE applications. This switch has six linear Tx/RX ports with isolation greater than 20 dB up to 2.7 GHz. Switching is controlled by the MIPI decoder. The SKY13525-646LF is available in a compact, 2 x 2 x 0.55 mm, 14-pin surface-mount QFN package and is ideal for embedded data cards and 2G/3G/4G multimode cellular tablets and handsets applications. Click here to view specs.

80 dB Variable Attenuator from DC to 2.55 GHz

The 50R-137 from JFW Industries is a variable attenuator that operates from DC to 2.55 GHz. It has an attenuation range from 0 to 80 dB with 10 dB steps. The attenuation level can be controlled manually using a single knob. This attenuator has an insertion loss of less than 1 dB and can handle up to 2 W of average input power and a peak power of up to 1 kW. It is available in a module with N/ SMA/ TNC (F) connectors. Click here to view specs.

Waveguide Band Stop Filter from 5850 to 5925 MHz

The AE5887WN2284 from Anatech is a waveguide bandstop filter with a stopband from 5850 to 5925 MHz. In the stop band, the filter has an attenuation of over 50 dB and has an insertion loss of 2.5 dB in the passband. It can handle an input power of up to 30 W. The filter is available in a module that measures 141 x 25 x 16 mm with SMA (F) connectors. Click here to view specs.

2.4 GHz Wi-Fi 6 Integrated Front End Module (iFEM)

The QPF7219 is an integrated front end module (iFEM) designed for Wi-Fi 6 (802.11ax) systems. It integrates a 2.4 GHz power amplifier (PA) with power detector, FCC bandedge BAW filter, regulator, transmit-receive switch (SPDT) and bypassable low noise amplifier (LNA) into a single device. The PA is optimized for a 5 V supply voltage that conserves power consumption while maintaining the highest linear output power of 25 dBm and leading edge throughput across all Wi-Fi channels 1 through 11, incompliance with the FCC regulatory limits. On the Rx side the FEM provides a gain of 15.5 dB with a noise figure of 2 dB. The receive path is pinned out so external filtering can be added in the optimal position. The device has integrated die level filtering for 2nd and 3rd harmonics as well as 5 GHz rejection for DBDC operation. It is available in a 5 x 3 mm LGA package and is ideal for access points, wireless routers, residential gateways and IoT applications. Click here to view specs.

125 W Amplifier from 0.7 to 6 GHz for EMC Test Applications

The 125S1G6 from AR RF/Microwave Instrumentation is a solid-state, Class A, self-contained, air-cooled, broadband amplifier that operates from 0.7 to 6 GHz. It is designed for applications where instantaneous bandwidth, high gain, and linearity are required. This broadband amplifier provides 125 W of output power with a gain of 52 dB when used with a sweep generator. It is available in a stylish contemporary cabinet that measures 19.8 x 11.8 x 24 inches with Type-N (F) connectors. The unit is designed for benchtop use but can be removed from the cabinet to be placed in a rack. The 125S1G6 is ideal for use as a driver amplifier in testing wireless and communication components and subsystems. The amplifier is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM and is also suitable for EMC Test applications where undistorted modulation envelopes are desired. The amplifier has built-in IEEE-488 (GPIB), RS-232 hardwire and fiber optic, USB & Etherne...Click here to view specs.

C-Band Solid State Bidirectional Amplifier from 4.4 to 5.1 GHz

The NW-BA-C-10-RX03 from NuWaves is a C-Band Solid State Bidirectional Amplifier module that operates from 4.4 to 5.1 GHz. The BDA has an auto-sense transmit/receive (T/R) control, with an extremely fast T/R mode switch time of under 2 uS. In Tx mode, it provides an output power of up to 10 watts with a gain of 12 dB and power efficiency of 20%. In Rx mode, it provides a gain of 10 dB with a noise figure of 3 dB. It is available in a module that measures 3.57 x 2.57 x 0.50 inches with SMA female, right angle connectors and is ideal for broadband RF telemetry, software-defined radios, Unmanned Aircraft systems and communication systems. Click here to view specs.

729 to 960 MHz Surface Mount Balun

The 0845BL05A0100 is a 1:2 impedance ratio balun (Unbalanced to Balanced Transformer) that operates from 729 to 960 MHz. It has an unbalanced port impedance of 50 ohms and a balanced port impedance of 100 ohms. The balun has an insertion loss of under 0.85 dB, return loss of over 9.5 dB and can handle an input power of up to 2 watts. It is available in a 0.65 x 0.5 x 0.45 mm surface mount package and is ideal for cellular, IoT, M2M applications. Click here to view specs.

150 W Linear X-Band SSPA Block Upconverter

The XTSLIN-150X-B1 from Xicomtech is a Solid State Block Up Converter that operates in the X-band with an input frequency from 950 MHz to 1450 MHz and an RF frequency from 7.9 to 8.4 GHz. It provides a linear output power of over 150 watts and a factory configurable small-signal gain of 65 to 75 dB while consuming only 875 VA of power. This is a lightweight converter that allows direct mounting to the antenna, minimizing waveguide RF losses and is ideal for mobile applications. It is available in a compact, rugged 32 lb. package that measures 17 x 10.5 x 6.8 inches, with forced air cooling to allow reliable operation over extended temperature ranges. The monitor and control (M&C) interface provides a component system status via Ethernet or RS-485 and RS-232. Click here to view specs.

14.4 to 14.83 GHz /15.15 to 15.35 GHz Ku-Band Diplexer

The UFDX9999 from MtronPTI is a Ku-band diplexer with Passband 1 from 14.4 to 14.83 GHz and Passband 2 from 15.15 to 15.35 GHz. It has an insertion loss of under 1 dB, isolation of more than 80 dB, and return loss of over 15 dB. The Diplexer can handle up to 50 watts of power. It is available in a module that measures 2.4 x 2.485 x 0.71 inches with SMA connectors and is ideal for Satcom and electronic warfare applications. Click here to view specs.

Microwave Signal Generator from 0.05 to 30 GHz

The SG30000 is an ultra-wideband microwave signal generator that operates from 0.05 to 30 GHz. It can generate signals with power levels from -60 to 10 dBm that have very low phase noise. This RF generator is fully programmable via SCPI commands, or the front panel interface. It has an Ethernet port for remote control and an integrated RMS power meter. It is available in a benchtop unit and is ideal for phase-noise sensitive applications in C, X, Ku, K, and Ka-band development and testing. Click here to view specs.

47 dBm GaN Power Amplifier from 2 to 6 GHz

The LW10-793605 from Linwave Technology is a solid-state GaN amplifier that operates from 2 to 6 GHz. This Class AB broadband amplifier provides a CW output power of 47 dBm with a small signal gain of 59 dB and a noise figure of less than 15 dB. It consumes less than 15 watts of input power and requires 28 volts of power supply. This HEMT based amplifier is available in a module that measures 185 x 90 x 16 mm with SMA (F) connectors and a discrete I/O interface. It is ideal for Electronic Warfare/Countermeasures, Broadband Mobile Jamming Applications, Airborne, Aircraft, and UAV Equipment, Power Amplifier Stage for Wireless Infrastructure, Test and Measurement Equipment, and General Purpose Broadband Transmitter Amplification applications. Click here to view specs.

UHF Gen2 Printable Mount on Metal Tag

The 116083 is a UHF Gen2 printable RFID tag that can be mounted on metal surfaces. It uses Alien Higgs 3 chip optimized for use at 915 MHz. This is a surface-independent tag that uses a patented inlay design and passive RFID technology to obtain excellent read ranges regardless of the surface metal, plastic, even wood. The printed label is constructed of durable, yet flexible polyester, which protects the copy, logo and/or bar code against moderate solvents and caustics/acids. Click here to view specs.

GaN on SiC Transistor X-Band Radars from 11 to 12 GHz

The IGT1112M90 from Integra is an X-Band Radar Transistor that operates from 10.8 to 11.8 GHz. This GaN-on-SiC RF power transistor supplies more than 90 watts of peak output power under 150µs, 10% duty cycle pulse conditions, with an associated 11 dB of gain and 43% efficiency. It operates from a 50 V supply voltage. The transistor is housed in a metal-based package with epoxy sealed ceramic lid and is best suited for X-band radar applications. Click here to view specs.

LDMOS Transistor from 2700 to 3100 MHz for Radar Applications

The BLS9G2731L-400 is an LDMOS power transistor that operates from 2700 to 3100 MHz. It delivers an output power of 400 watts with a gain of 13 dB and has a drain efficiency of 47%. The transistor is available in a flanged ceramic package with integrated dual-sided ESD protection and is compliant to Directive 2002/95/EC, regarding Restriction of Hazardous Substances (RoHS). It is ideal for S-band radar applications. Click here to view specs.

LO Buffer Amplifier from 20 to 55 GHz

The AMM-6702 from Marki Microwave is broadband MMIC LO buffer amplifier that operates from 20 to 55 GHz. It is designed to provide a strong, flat output power response when driven with an input power at 0 dBm. The amplifier provides a saturated output power of 22 dBm and a gain of 28 dB with a noise figure of 6 dB. It is available as a bare die or a connectorized module. The amplifier has built-in DC blocking capacitors on the input and output. Click here to view specs.

80-2690 MHz and 3300-5925 MHz Diplexer with No DC Pass

The FDFX55020S4-NC from RFS is a Diplexer with a low passband from 80 to 2690 MHz and a high passband from 3300 to 5925 MHz (CBRS/LAA). It has an insertion loss of under 0.5 dB, an attenuation of 50 dB, and a return loss of over 16 dB. The Diplexer can handle up to 160 watts of power and is available in a module that measures 96 x 79 x 30 mm with 4.3-10 connectors. The diplexer is ideal for small cell and 5G network densification projects. This robust diplexer can be deployed in any indoor or outdoor small cell or macro network environment and provide IP67 protection against dust and water as well as built-in lightning protection. Click here to view specs.

2-Way Wideband Power Divider from 2 to 19 GHz

The ENGPD00014 from ENGIN-IC is a 2-way wideband power divider that operates from 2 to 19 GHz. It has an insertion loss of less than 2.5 dB, isolation of more than 12 dB, and a return loss of over 20 dB. This power divider can handle an input power of up to 27 dBm and has an amplitude balance of 0.1 dB and a phase balance of 1 degree. It is available as a die that measures 2.76 x 2.26 x 0.1 mm and is ideal for applications like Space Hybrids, Military Hybrids, Microwave Radios, and Test and Measurement Systems. Click here to view specs.

Helical GNSS Antenna for UAV Applications

The HC871 is a lightweight helical antenna covering the GPS L1/L2, GLONASS G1/G2, Galileo E1, and BeiDou B1 frequency bands, designed and crafted for precision positioning. It has a precision-tuned helix element that provides excellent axial ratios and operates without the requirement of a ground plane, making it ideal for a variety of high-precision Unmanned Aerial Vehicle (UAV) applications. This antenna has a low current Low Noise Amplifier (LNA) that includes an integrated low-loss pre-filter to protect against harmonic interference from high amplitude signals, such as 700 MHz band LTE and other near in-band cellular signals. The HC871 is ideal for L1/L2 RTK surveying systems, military & security and mission-critical GPS timing applications. It is protected by a robust, military-grade plastic enclosure with an integrated SMA connector for screw-on mounting that securely seals the unit with an O-ring complying with IP67 standards. Click here to view specs.

Bandpass Filter

Lowpass Filter

Highpass Filter

Band Reject Filter

Diplexer

Triplexer

Flexible

Attenuators

Bends

Circulators

Directional Couplers

Isolators

Phase Shifter

Rotary Joints

Straights

Termination

Transitions

Waveguide to Coax Adapters

Rigid PCB Quotes

Flexible PCB Quotes

PCB Assembly Quotes

PCB Design Quotes

PCB Repair Quotes

PCB Stencil Quotes

Latest RF & Microwave Products of the Week (1 - 7 Aug, 2019)