Latest RF & Microwave Products of the Week (11 -17 April, 2019)

3400 to 3600 MHz Single-Junction SMT Circulator

The SKYFR-001657 from Skyworks is a single-junction, surface-mount circulator that operates from 3400 to 3600 MHz. The compact, high performance device can handle an input power of up to 15 watts and has a low insertion loss of 0.25 dB. This robust lead circulator is ideal for 5G massive MIMO, small cell, wireless infrastructure and power-amplifier applications. It has an operating temperature range of -40 °C to +105 °C. Click here to view specs.

Tunable Low-Pass Filter from 3.95 to 6.9 GHz

The HMC882A is a tunable MMIC low-pass filter that has an user-selectable cutoff frequency (f3dB), which can be varied from 3.95 to 6.9 GHz by applying a single analog tuning voltage between 0 V and 14 V. This low-pass filter has a low insertion loss of 3 dB, return loss of 13 dB, and over 20 dB of stopband attenuation at 1.28 x f3dB GHz. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. It has excellent microphonics due to the monolithic design with a low residual phase noise of -165 dBc/Hz, and provides a dynamically adjustable solution for advanced communications applications. The low-pass tunable filter is available in a 5 x 5mm LFCSP package and is ideal for satcom, space, military radar, electronic warfare and test & measurement applications. Click here to view specs.

8-Channel Digital Attenuator from 0.2 to 6 GHz

The LDA-906V-8 from Vaunix is a highly accurate, bidirectional, 8-Channel Digital Attenuator that operates from 0.2 to 6 GHz. It has a step size of 0.1 dB and typical accuracy <0.25 dB over a 90 dB of control range. This lab brick can handle up to 26 dBm of input power. This Digital Attenuator a portable USB powered device that is sized to fit into a single rack unit for ATE applications. It can be used with WiMAX, 3G, 4G, 5G, LTE, DVB and microwave radio fading simulators as well as in engineering and production test labs. This attenuator module has a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems. The attenuators are easily programmable ...Click here to view specs.

700 W High Power RF LDMOS FET from 1.2 to 1.4 GHz

The PTVA127002EV-V1 from Wolfspeed is a RF LDMOS FET that operates from 1.2 to 1.4 GHz. It provides a peak output power of 700 W and a gain of 16 dB with a drain efficiency of 56%. The device is available in a thermally-enhanced package with bolt-down flange and is ideal for use in power amplifier applications. Click here to view specs.

28.8 MHz, High Stability Sine Wave TCXO

The TCXO911BT-28.8MHz-A-V from Dynamic Engineers is high stability TCXO with a frequency of 28.8 MHz. This TCXO requires a 3.3 V supply voltage and provides a Sine Output waveform with a stability of 0.2 ppm and phase noise of less than -140 dBc/Hz @ 1 KHz. It is available in a compact package that measures 11.4 x 9.6 x 2.8 mm. This TCXO can be used in a wide range of applications including mobile radio and communication equipment. Click here to view specs.

19 dBm Power Amplifier from 40 to 60 GHz

The SPU-20-20W is a MMIC-based, power amplifier that operates from 40 to 60 GHz. It provides an output power of 19 dBm with a gain of 20 dB, while operating from a supply voltage of 8 to 12 VDC. The PA has WR-19 UG 383/U Mod flanges at the Input/output ports. It has an integrated heat sink with a DC fan, which can be removed when being integrated. Click here to view specs.

Solid State High Power Amplifier from 26.5 to 40 GHz

The AMP3132A from Exodus Advanced Communications is a solid state high power amplifier that operates from 26.5 to 40 GHz. It delivers an output power of more than 15 watts with a gain of over 52 dB and has a noise figure of less than 12 dB. This Class AB linear GaAs amplifier requires a supply voltage of 8 VDC and consumes 32 A of current. It is available in a module with 2.92 mm K-type female connectors. This SSPA is suitable for all single channel modulation standards, has built-in protection circuits and an instantaneous wide bandwidth. Click here to view specs.

30 W LDMOS Power Amplifier from 2620 to 2690 MHz

The PCM5M5OGJ (SKU 7112) from Empower RF is a 30 watt solid state power amplifier that operates from 2620 to 2690 MHz. It delivers a gain of 42 dB with low distortions, and excellent group delay and phase linearity. This amplifier provides excellent performance and long term reliability by using Direct Injection Pre-distortion, advanced matching networks and combining techniques (Doherty Design), EMI/RFI filters, machined housings, and qualified components. The PCM5M5OGJ is available in a module that measures 4.4 x 6.7 x 1.1 inches with SMA female connectors and has built-in output isolator and control and monitoring circuits. This LDMOS amplifier module is suitable for a wide range of applications, including LTE repeater applications. Click here to view specs.

0.2 to 2.5 GHz SDLVA with 65 dB Dynamic Range

The SDLVA-0120-70-0225 from PMI is a successive log detection video amplifier (SLDVA) that operates from 0.2 to 2.5 GHz. It has a dynamic range of 65 dB, a TSS of -65 dBm and a nominal video bandwidth of 20 MHz. The SDLVA is available in a module and is ideal for high speed channelized receiver applications. Click here to view specs.

2-Way GPS DC Blocking Power Divider from 0.6 to 6 GHz

The DC802-2-3.300WWP from MECA is a 2-way GPS DC blocking power divider that operates from 0.6 to 6 GHz. It has an insertion loss of under 1.3 dB, isolation of over 17 dB and exceptional amplitude & phase balance of 0.3 dB & 5 degrees. The power divider can handle an input power of up to 30 watts. It is available in a module with SMA female connectors. Click here to view specs.

8-Way Power Divider from 6 to 18 GHz

The PD-NS00-8S from UMCC is a 8-way power divider that operates from 6 to 18 GHz. It has an insertion loss of under 2.2 dB, isolation of over 18 dB and can handle an average input power of up to 10 watts. The device is available in a module with SMA female connectors. Click here to view specs.

6 dB SMT Directional Coupler from 5 to 1000 MHz

The CPA-1001-56H from MiniRF is a Surface Mount Directional Coupler than operates from 5 MHz to 1000 MHz. It provides a coupling of 6.5 dB with a directivity fo 15 dB and insertion loss of 1.9 dB. This small, low cost surface mount coupler is matched to 50 ohms at the ports and has a return loss of 18 dB. It can be used in a wide range of wireless and communication systems. Click here to view specs.

2x Frequency Multiplier from 10 to 20 GHz

The ASX40B-217 from Wright Technologies is a frequency doubler with an input frequency of 10 to 20 GHz and output frequency from 20 to 40 GHz. It provides an output power of over 17 dBm when driven by a single DC bias supply. This device has a harmonics of -20 dBc and spurious of -60 dBc. It is available in a module with SMA, 2.9 mm and 2.4 mm connector options. The ASX40B-217 is ideal for radar systems, electronic warfare, telecom, satcom and military applications. Click here to view specs.

71 to 76 GHz Faraday Isolator

The HMI12-387-73.5-5.0 from HXI is an isolator that operates from 71 to 76 GHz. This ferrite based junction isolator provides an isolation of over 19 dB with an insertion loss of less than 1 dB. It can handle up to 0.5 Watts of power with a VSWR of 1.5:1. This isolator has been specifically designed for the matching and protection of E-band radios, radars and testing systems. It has a WR-12, UG-387/U waveguide interface. Click here to view specs.

Ultra Small Dual Band WiFi 11a/b/g/n+Bluetooth 5.0 Module

The Type 1LV from Murata is an ultra small, 2.4 & 5 GHz WiFi 11a/b/g/n + Bluetooth 5.0 Module. It is based on Cypress CYW43012 combo chipset which provides up to 72.2 Mbps PHY data rate on Wifi and 3 Mbps PHY data rate on Bluetooth. The module also supports Bluetooth 4.2 features, LE Secure Connections, LE Privacy 1.2 and LE Data Packet Length Extension. This module is packaged in a small, shielded surface mount package measuring 10 x 7.2 x 1.4 mm and is ideal for IoT applications, handheld wireless systems and gateways. The WLAN section supports SDIO v2.0 SDR25 interface and the Bluetooth section supports high-speed 4-wire UART interface and PCM for audio data. Click here to view specs.

High-performance Sub-1 GHz Transceiver for Narrowband Systems

The CC1120 from TI is a fully integrated Sub-1 GHz RF transceiver designed for Industrial, Scientific, and Medical (ISM) applications and Short Range Device (SRD) frequency bands at 164 to 192 MHz, 274 to 320 MHz, 410 to 480 MHz, and 820 to 960 MHz. It has an excellent receiver sensitivity of -123 dBm at 1.2 kbps, -110 dBm at 50 kbps and a low phase noise of -111 dBc/Hz at 10 kHz offset. The transceiver provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication, and wake-on-radio. It is available in a 5 x 5 mm QFN package and is ideal for narrowband wireless systems, wireless metering, IEEE 802.15.4g systems and mobile radios applications. This transceiver is compliant to Europe: ETSI EN 300 220, ETSI EN 54-25; US: FCC CFR47 Part 15, FCC CFR47 Part 90, 24, and 101 and Japan: ARIB RCR STD-T30, ARIB STD-T67, ARIB STD-T108 regulations. Click here to view specs.

5G NR Sub 6 GHz module for IoT and M2M Applications

The RM500Q from Quectel is a 5G NR sub-6 GHz module, compliant with 3GPP Release 15 specifications and capable of both 5G standalone (SA) and non-standalone (NSA) modes of operation. This module supports LTE Category 22 connectivity with integrated GNSS and eSIM. It optimized specially for IoT/eMBB applications and is ideal for global deployment. The module integrates Qualcomm Snapdragon X55 5G modem with RF transceiver, RF Front-End (RFFE) and antenna elements from Qualcomm Technologies. It supports Qualcomm IZat location technology Gen8C Lite (GPS, GLONASS, BeiDou and Galileo). The RM500Q module is designed for enterprise and mobile broadband applications such as fixed wireless access, mobile hotspot devices, Always Connected PCs, and public safety and surveillance applications. Available in an M.2 form factor, the RM500Q is compatible with Quectel LTE-A Cat 6 module EM06, Cat 12 module EM12 and Cat 20 module EM20, which will facilitate customers to migrate from LTE-A to 5G. Click here to view specs.

GPS Module with Integrated Antenna

The ORG1410 from Origin GPS is an ultra-compact GPS module with an integrated antenna for cost-sensitive applications. This miniature multi-channel GPS receiver with support for SBAS, QZSS and other regional overlay systems, continuously tracks all satellites in view, providing real-time positioning data in the industry standard NMEA format. It offers excellent sensitivity, achieving rapid TTFF in less than one second with an accuracy of approximately two meters, and tracking sensitivity of -163 dBm. The ORG1410 chipset integrates an antenna, dual-stage LNA, RF LDO, SAW filter, TCXO, RTC crystal and RF shield with market-leading SiRFstarIV&trade GPS SoC. It is available in a compact package that measures 10 mm x 10 mm has been designed to support compact and traditional applications such as smart watches, wearable devices, asset trackers and other applications that requires a compact, low power GPS solution. Click here to view specs.

902 to 928 MHz UHF RFID Tag for On-Metal Asset Tracking

The AD-454r6-P from Avery Dennison is an ISO-18000-6C, EPC Class 1 Gen 2 UHF RFID tag that operates from 902 to 928 MHz (Globally). It has been developed using the Impinj Monza R6 chip. This RFID tag measures 2.75 x 0.75 inches and has an EPC memory of 128/96 bits, USER memory 32/64 bits and TID memory of 48 bits. It is ideal for on-metal asset tracking applications. Click here to view specs.

Spectrum Analyzer from 10 Hz to 44 GHz with 200 MHz Analysis Bandwidth

The R&S FSV3000 is signal and spectrum analyzer that operates from 10 Hz to 4, 7.5, 13.6, 30 or 44 GHz. It has an analysis bandwidth up to 200 MHz and a SSB phase noise of –107 dBc/Hz at a 10 kHz offset. The analyzer can measure EVM values better than 1 % for a 100 MHz signal at 28 GHz. With frequency coverage up to 44 GHz, this analyzer is ideal for analyzing 5G NR signals. It can simplify troubleshooting rare events and setting up complex measurements. With the event based action GUI, whenever a predetermined event occurs the corresponding action, such as saving a screenshot or I/Q data, is performed. The analyzer has been designed to help users set up complex measurements in the simplest and fastest way possible. It is easy to use, has a high measurement speed, making it ideal for labs and production lines. Furthermore, the embedded SCPI recorder makes it much easier to create executable scripts, since all manual input is translated into plain SCPI or into the syntax o...Click here to view specs.

Remote Controlled Real Time Spectrum Analyzer from 8 kHz to 8 GHz

The SignalShark 3320 is a Real-Time Spectrum Analyzer that operates from 8 kHz to 8 GHz. It is capable of detecting, analyzing and classifying a wide range of signals, as well as locating the source of transmissions using either automatic direction finding or TDOA (time difference of arrival) techniques. The instrument uses advanced FFT computations to achieve a 40 MHz real-time instantaneous bandwidth with a 100% probability of intercept (POI) for signals longer than 3.125 µs. The unit also captures the spectrum over the full frequency span of 8 kHz to 8 GHz in a single measurement at the impressively fast scan rate of 50GHz/s. The 3320 is equipped with an excellent RF front-end delivering outstanding sensitivity and dynamic range. It also provides four switchable RF inputs, which allow several different antennas – covering different frequency bands, for example – to be connected at the same time without the need for a complex switch that conventional single-inpu...Click here to view specs.

Coaxial RF Limiter 30 to 3000 MHz

The LIM30M3G is an RF limiter that protects against ESD and input power surges over a frequency range of 30 to 3000 MHz. It limits an input power range from 12 to 30 dBm to 11.5 dBm at the output. The limiter has a low insertion loss of 0.23 dB and a recovery time of 10 nsec. It is available in a small 1-1/8 x 15/16 x 0.59 inches shielded RF enclosure and is ideal for stabilizing RF outputs, reducing amplitude variations and protecting LNA in hostile environments. Click here to view specs.

Bandpass Filter

Lowpass Filter

Highpass Filter

Band Reject Filter

Diplexer

Triplexer

Flexible

Attenuators

Bends

Circulators

Directional Couplers

Isolators

Phase Shifter

Rotary Joints

Straights

Termination

Transitions

Waveguide to Coax Adapters

Rigid PCB Quotes

Flexible PCB Quotes

PCB Assembly Quotes

PCB Design Quotes

PCB Repair Quotes

PCB Stencil Quotes

Latest RF & Microwave Products of the Week (11 -17 April, 2019)