Latest RF & Microwave Products of the Week (9

2x2 MIMO, 5 GHz Front End Module for Wi-Fi 6

The WLAN8101C from NXP is a 5 GHz 2 x 2 MIMO Front End Module that supports WLAN IEEE802.11a/n/ac/ax and Wi-Fi 6. It includes two monolithic front-end ICs. Each IC has an integrated WLAN amplifier, an integrated Bluetooth amplifier, a low noise amplifier with bypass functionality, directional couplers, and an SPDT switch. The module also includes coexistence filters for both transmit and receive channels. The device is matched to 50 Ω and integrates harmonics and out of band filtering which minimizes the layout area in the application. The WLAN8101C is available in a 3 x 4 mm package and is suitable for applications in WLAN, Wi-Fi 6, smartphones, tablets, netbooks, and other portable computing devices. It is also suitable for embedded system applications. Click here to view specs.

5 GHz Front-End Module for WLAN Applications

The SKY55501-1 from Skyworks is a 5 GHz Front-End Module (FEM) that supports simultaneous 5 GHz WLAN and licensed assisted access (LAA) systems. This highly-integrated module incorporates a 5 GHz low-noise amplifier (LNA) with bypass supporting 5 GHz WLAN and LAA simultaneous RX reception, and an SPDT transmit/ receive (T/R) switch. The FEM has a receive gain of 12.5 dB, a bypass loss of 8.5 dB and requires a supply voltage if 3.7 V. It is available in a 1.7 × 2.1 × 0.7 mm 20-pin Multi-Chip Module (MCM) package and is ideal for connected home applications and is suitable for smartphones, tablets, Wi-Fi-enabled handsets, mobile/portable systems, and 5G new radio applications. Click here to view specs.

2.4 GHz BAW Wi-Fi Filter with Sharp Band Edges

The QPQ1909 from Qorvo is a Bulk Acoustic Wave (BAW) Band-Pass Filter with extremely steep skirts, simultaneously exhibiting low loss in the Wi-Fi band (Channels 1-14) and high rejection above 2500 MHz and below 2400 MHz. The high-performance, high power filter module has been specifically designed to enable band-edge performance in Wi-Fi applications which result in higher regulatory power capability than with traditional filter solutions. With Channels 1-14 enabled, users can accommodate any regulatory region needed by the end product. In the passband, the QPQ1909 has an insertion loss of less than 0.9 dB and can handle up to 30 dBm of average input power. The filter is available in a 1.4 x 1.2 mm laminated package and is suitable for access points, wireless routers, residential gateways, customer premise equipment, and IoT applications. Click here to view specs.

1-Port USB Vector Network Analyzer, 85 MHz to 14 GHz

The R140 VNA is a 1-port USB powered VNA that operates from 85 MHz to 14 GHz. The VNA is the size of a deck of cards and can be controlled by any Windows PC or laptop. The R140 provides a wide variety of analysis capabilities, including time-domain with gating and DTF measurements at no additional cost. Collection of metrology-grade S-parameter test results can be achieved manually or through automation in Python, MATLAB, Excel, C++, VB.NET, or LabVIEW. Click here to view specs.

High Precision GPS/GNSS/SBAS/RTK/L1/L2 Active Screw Mount Antenna

The 2J6901BC2F from 2J Antennas is a GNSS Active Antenna that supports GPS/ GLONASS/ BeiDou/ QZSS/ Galileo/ RTK services while operating from 1561 to 1606 MHz in the L1 band and at 1227.6 MHz in the L2 band. This high precision, low profile external antenna is designed for demanding GPS applications that require centimeter-level accuracy by combining Precise Point Positioning (PPP) of L1 and L2 with Real-Time Kinematic (RTK) satellite navigation. The antenna delivers an active gain of 28 dB with a noise figure of less than 1.6 dB and requires a supply voltage of 2.3 to 6 V. The antenna provides a passive peak gain of up to 5.3 dBi with an axial ratio of up to 3 dB and an out-of-band rejection of 40 dB. Used for both receiving and transmitting applications, this active antenna is ideal for external environments where longer remote cable runs are required. This antenna is ideal for land and hydrographic survey applications because it uses real-time error corrections while simultaneou...Click here to view specs.

60 Watt L & S-Band Power Amplifier from 960 to 1390 MHz

The L60T01 from Nuwaves is an L & S-Band Power Amplifier that delivers 60 watts of RF power from 960 to 1390 MHz to extend the operational range of airborne telemetry links and transmitters. It can handle an RF input power of 0 dBm (1 mW) and provides 48 dB of gain for continuous wave (CW) and near-constant-envelope waveforms. The device is available in a module that measures 4.50 x 3.50 x 0.61 inches with SMA female connectors and is ideal for RF telemetry, tactical communication systems, and electronic warfare systems. The amplifier has over-voltage protection and can operate over a wide temperature range of -40 °C to +85 °C (baseplate). Click here to view specs.

3.4 to 3.6 GHz Ceramic Band Pass Filter for 5G Applications

The AM3500B1093 from Anatech Electronics is a Ceramic Band Pass Filter with a passband from 3400 to 3600 MHz for 5G Applications. It has a passband insertion loss of less than 1.7 dB and can handle an input power of up to 2 watts. The filter has an I/O impedance of 50 ohms and provides an attenuation of 28 dB above and below the passband. This RoHS-compliant ceramic filter is available in a surface-mount package that measures 10.2 x 6.2 x 4 mm. It is also available in module with SMA(F) connectors. Click here to view specs.

U-band Active 4x Frequency Multiplier from 40 to 60 GHz

AT-AM4-4060-18 from AT Microwave is a U-band, Active 4x Frequency Multiplier that converts an input frequency from 10 to 15 GHz to an output frequency from 40 to 60 GHz. It can handle up to 10 dBm of input power and delivers an output power of 18 dBm. This multiplier requires a supply voltage of 5V while consuming 600 mA of current and has a harmonic suppression of -15 dBc. It has an SMA female input port and a WR-19 waveguide interface at the output port. This multiplier is suitable for U-band communication, test equipment, RoF (RF Over Fiber), and radar system applications. Click here to view specs.

6 Way, 30 Watt Power divider from 0.5 to 6 GHz

The 806-2-3.250WWP from MECA is a 6-way power divider that operates from 0.5 to 6 GHz covering all ISM and Public Safety bands. It can handle up to 30 watts of power, has an insertion loss of under 3 dB and isolation over 13 dB. The power divider is available in a module with SMA Female connectors. Click here to view specs.

30 W 8-Way Power Divider from 9 to 10 GHz

The 10A8NA-8S-S from Renaissance Electronics is an 8-way Power Divider that operates from 9 to 10 GHz. This X-band splitter has an insertion loss of 0.9 dB, an isolation of 23 dB, and can handle 30 watts of CW power. The device has a phase balance of 1 degree and an amplitude balance of 0.1 dB. Compliant with NASA outgassing requirements, this power divider is available in a module that measures 1 x 4.11 x 0.313 mm with coaxial connectors. Click here to view specs.

Solid State USB Programmable Attenuator from 30 to 3000 MHz

The 50P-2055 from JFW Industries is a solid state USB programmable attenuator that operates from 20 MHz to 3000 MHz. It has an attenuation range of 95 dB, a step size of 0.5 dB and a switching speed of 4 us. The attenuator can handle an input power of up to 27 dBm. It has SMA connectors at the input and output ports which are matched to 50 ohms. Click here to view specs.

Low Noise Amplifier IC for GNSS and Satellite Radio Applications

The CA3509M4 from CEL is an L to S-Band Low Noise Amplifier IC for GNSS and Satellite Radio Applications that operate at 1.575 GHz. It delivers an output power of 12 dBm with a gain of 17 dB and has a noise figure of 0.4 dB. The amplifier IC is available in a flat-lead 4-pin thin-type super mini mold package with an on-chip ESD protection diode. It is suitable for Global Navigation Satellite Systems (GNSS) like GPS, GLONASS, Beidou and Galileo, satellite radio (SDARS, DMB, etc.) antenna, and microwave communication applications. Click here to view specs.

600 W Power LDMOS Module from 902 to 928 MHz for ISM Applications

The BPF0910H9X600 from Ampleon is a Power LDMOS Module that operates from 902 to 928 MHz. The device provides 600 watts of CW power with a gain of over 17 dB and a drain efficiency of 69 % while operating from a 50 V supply. It features a built-in temperature sensor and temperature compensation networks. This 50-ohm module measures 92 x 60 mm and is ideal for Heating and ISM (Industrial, Scientific, and Medical) Applications. Click here to view specs.

2-Way Balun from 20 to 1000 MHz

The IPP-5003 is an RF balun that operates from 20 to 1000 MHz. This 2-way device has an insertion loss of less than 0.5 dB and can handle an input power of up to 100 watts. It has been tuned to have a low amplitude balance of 0.45 dB and a phase balance of 6 degrees. The balun is available in a 1.10 x 1.15 inches SMD package. Click here to view specs.

RF Signal Generator from 50 to 13000 MHz with Ultra-Low Phase Noise

The SG12000PRO from DS Instruments is an RF Signal Generator that operates from 50 MHz to 13 GHz (10 MHz to 15 GHz in uncalibrated mode) with a step size of 10 Hz. It can generate an output power level of up to 10 dBm with a dynamic range of 70 dB. It generates a signal with a low phase noise of -94 dBc @10 kHz. The phase noise of the generated signal is 30 dB lower than the standard SG12000. The generator is powered from a standard UCB-C connection and has a bright OLED display with front control buttons to provide a quick alternative to USB control. This 50-ohm signal generator measures 2.75 x 1.25 x 4.15 inches and is available with SMA connectors. The device is ideal for use in automated testing environments, general RF labs, flexible LO sourcing, antenna design, EMC testing, production verification, and testing, educational/university lab use, aerospace/defense research, 802.11n development/testing, and LTE engineering applications. Click here to view specs.

GaAs Power Amplifier MMIC from 0.1 to 9 GHz

The AM009024WM-QN5-R from Amcom Communications is a GaAs Power Amplifier MMIC that operates from 0.1 to 9 GHz. It provides a P1dB of 24 dBm with a small signal gain of over 18 dB. This RoHS-compliant MMIC is available in a QFN package with both RF and DC leads at the bottom of the package to facilitate low-cost SMT assembly to the PC board. This amplifier can be used as a gain block and in a wide range of applications including software radios, and instrumentation applications. Click here to view specs.

4800 MHz Voltage Controlled Oscillator with Low Phase Noise

The CVCO55CC-4800-4800 from Crystek Corporation is a Voltage Controlled Oscillator that operates at 4800 MHz. The device has a tuning voltage range from 0.5 to 4.5 VDC and has a tuning sensitivity of 15 MHz/V. It delivers an output power of up to 6 dBm and has a low phase noise of -122 dBc/Hz @100 kHz offset. The VCO is available in an SMD package that measures 0.5 x 0.5 inches and is ideal for use in applications such as digital radio equipment, fixed wireless access, satellite communications systems, and base stations. Click here to view specs.

Dual Polarized Omni-Directional Antenna from 4.4 to 6.05 GHz

The MA-WO52-DP7 from Mars Antennas is an Omni-Directional Antenna that operates from 4.4 to 6.05 GHz. This dual-polarized antenna delivers a gain of 7 dBi and can handle an input power of up to 10 watts. It has a port-to-port isolation of 35 dB and a VSWR of less than 2.5:1. The antenna measures 420 (H) x 66 (D) mm and is available with N-type female connectors. This IP67-rated antenna has a UV protected radome which makes it suitable to operate in a harsh environment. It has been designed for use in mesh networks, WLL, WLAN, ISM, point-to-point, and point-to-multipoint applications. Click here to view specs.

Multi-Band LTE CAT 1 Module for Global Use

The SIM7600G from SIMCom is a Multi-Band LTE-FDD/ LTE-TDD/ HSPA+ and EDGE/ GPRS/ GSM module which supports LTE CAT1 Globally. It is designed for applications that need high throughput data communication in a variety of radio propagation conditions. The module has uplink data rates of up to 5.76 Mbps and downlink data rates of up to 42 Mbps. This module requires a supply voltage of 3.8 V. It has a strong extension capability with rich interfaces including UART, USB2.0, GPIO, ADC, etc. The module is available in an LCc+LGA package (30 X 30 X 2.9 mm) and it is compatible with SIMCom’s SIM7600x modules. AT commands of SIM7600G are mostly compatible with SIM7500/SIM7600 Series modules. This RoHS compliant module is available with CE, FCC, and REACH approvals. Click here to view specs.

Bandpass Filter

Lowpass Filter

Highpass Filter

Band Reject Filter

Diplexer

Triplexer

Flexible

Attenuators

Bends

Circulators

Directional Couplers

Isolators

Phase Shifter

Rotary Joints

Straights

Termination

Transitions

Waveguide to Coax Adapters

Rigid PCB Quotes

Flexible PCB Quotes

PCB Assembly Quotes

PCB Design Quotes

PCB Repair Quotes

PCB Stencil Quotes

Latest RF & Microwave Products of the Week (9 - 15 April, 2020)