5G products encompass a wide range of devices and equipment designed to support and enable 5G wireless communication networks. These products play a crucial role in realizing the potential of 5G technology, enabling faster data speeds, lower latency, increased network capacity, and support for a wide range of innovative applications and services. everything RF has compiled a list of 5G products that are new and trending on everything RF in February 2024. To keep up to date with 5G from an RF point of view, visit the 5G Hub on everything RF where we keep users up to date with new products, news, whitepapers, webinars, and events.
Dual Channel IF Transceiver IC from 37 to 48.2 GHz
The AWMF-0196 from Anokiwave is a Dual Channel IF Transceiver IC that operates from 37 to 48.2 GHz covering n260, n259, and n262 3GPP bands. It has integrated dual Tx single-sideband up-conversion, dual Rx image-reject down-conversion functionality, and an on-chip PLL/VCO LO synthesizer that enables 2T2R applications. This transceiver has an on-chip frequency multiplier that simplifies board-level integration for use with either an internal frequency synthesizer or an external PLL. It also has an on-chip selectable LO multiplication, high IF support, LO multiplexing to remove the need for external switches for MIMO operation, and a high-power PA eliminating the need for an external driver IC. Read more
mmWave Up/Down-Converter from 24.25 to 29.5GHz
The F5701 from Renesas is a RF Up-down Converter with Gain 22.5 to 29.5 dB (Conversion Gain), IF Frequency 2.5 to 6 GHz, LO Frequency 18.25 to 27 GHz, Noise Figure 5.6 dB, P1dB -17.6 dBm. Tags: Surface Mount. More details for F5701 can be seen below. Read more
Multi-Band Cellular/4G Antenna from 698 to 2700 MHz
The AC97002-100 from Antenna Company is a Multi-Band Cellular/4G Antenna that operates from 698 to 960 MHz and 1700 to 2700 MHz. This omnidirectional antenna has an efficiency of 70%. It has been designed to minimize installation time, eliminate the need to investigate multiple mounting locations during installation and improve the success rate of mounting inside metal cabinets. This antenna is suitable for customers deploying infrastructure for smart utility applications such as smart metering (connection to gateways), asset management, and vending machines. It radiates signals that can easily penetrate indoor environments, especially conductive and non-conductive surfaces. Read more
4G-LTE/5G-NR Front-End Module for Automotive Applications
The SKY5A3047 from Skyworks is a Front-End Module for 4G LTE and 5G NR applications. It consists of power amplifier (PA) blocks, low-noise amplifier (LNA) blocks, two Mobile Industry Processor Interface (MIPI) v3.0 standard digital control blocks and integrated duplexers. This module includes a multiple gain state average power tracking mode, integrated filters, antenna port and band select switches. It has an enhanced architecture that covers multiple bands and meets the spectral linearity requirements of LTE QPSK, 16QAM, and 64QAM modulations and New Radio DFTS-OFDM and CP-OFDM modulations up to 190 MHz bandwidth. Read more
Differential-to-Single-Ended RF Amplifier from 4.4 to 5 GHz
The ICASD4450-D2S from iCana is a Differential-to-Single-Ended Gain Amplifier that operates from 4.4 to 5.0 GHz. It provides a gain of 16.5 dB with a noise figure of 3.6 dB and has an output P1dB of 17 dBm. This amplifier is manufactured using GaAs technology that exhibits low noise figures and high linearity, allowing it to be used in both receiver and transmitter applications. It is ideal wireless infrastructure and operates in major 3GPP bands. This gain amplifier does not require an external choke inductor and is over-molded with an input impedance of 100 ohms and an output impedance of 50 ohms. Read more
Fully-Integrated V2X SoC for Day 1 and Future Day 2 Applications
The TEKTON3 from Autotalks is a V2X SoC that is designed for Day 1 and future Day 2 use cases. It has embedded Day 1 and Day 2 radios operating concurrently with both radios using two antennas with full transmit and receive diversity. The Day 1 radio supports either LTE-V2X (C-V2X Rel. 14/15) or DSRC and the Day 2 radio supports either 5G-V2X (C-V2X Rel. 16/17/18) or DSRC+ (IEEE802.11bd). The Day 2 radio is used for cooperative perception, which means that a vehicle can ‘see’ what the other vehicle is ‘seeing’. This enables two vehicles to share the information they receive and have even better road awareness. Read more
Sub-6 GHz Rel-17 Multi-band 5G NR/LTE-FDD/LTE-TDD Modules
The SIM8230X from SIMCom are Sub-6 GHz Multi-Band 5G NR/LTE-FDD/LTE-TDD Modules. They have a 3GPP Rel-17 Compliant 5G Standalone architecture, with a downlink data rate of up to 220 Mbps and an uplink data rate of up to 100 Mbps. These modules require a DC supply from 3.3 to 4.4 V. They are available in LGA + LCC packages that measure 30.0 x 30.0 x 2.5 mm and can be controlled via USB 2.0, PCM, I2C, PCIe, and GPIO interfaces. The modules are ideal for applications that require large amounts of data transmission in various wireless applications. Read more
Thermally-Enhanced OCXO from 10 to 50 MHz for 5G/6G RANs
The ROM1490X from Rakon is an Oven-Controlled Crystal Oscillator (OCXO) that operates from 10 to 50 MHz. It provides a CMOS output waveform with an SSB phase noise of -155 dBc/Hz (at 1 kHz offset) and has a frequency stability of ±3 ppb. This OCXO has a warm-up time of 180 seconds and a g-sensitivity of 0.9 ppb/g. It incorporates Rakon’s proprietary Mercury™ ASIC and XMEMS® resonator technologies to provide increased stability and holdover performance. This oscillator is designed for data centre synchronization, 5G base stations and small cells, 5G Advanced and 6G radio access networks (RAN). It requires a DC supply from 2.7 to 5 V and consumes less than 440 mW of power. Read more
5G-NR Bandpass Filter with Passband from 37 to 40 GHz
The FT-BPF-n260-C from TMYTEK is a Bandpass Filter with a passband from 37 to 40 GHz covering the 5G-NR n260 band. It has a passband insertion loss of 4 dB and provides 40 dB of rejection both above and below the passband. This filter is available in a RoHS-compliant package that measures 47.78 x 29.33 x 13.74 mm with 2.92 mm (female) connectors and is ideal for 5G communication, SATCOM, or radar applications. Read more
100 W, Low-PIM RF Termination from 350 to 5925 MHz
The TK-6100ME from Microlab is an RF Termination that operates from 350 to 5925 MHz. It can handle an average input power of 100 W and a peak input power of 5 kW. This 50-ohm termination has a PIM (2x20 W) of -161 dBc and a VSWR of less than 1.30:1. It is available in an IP67-rated module that measures 8.27 x 3.50 x 2.48 inches with 4.3-10 (Male) connector and is designed for 5G, C-band, and LAA applications. Read more
mm-Wave SPDT Switch from 37 to 49 GHz for 5G Applications
The ADRF5301 from Analog Devices is a Silicon-Based SPDT Switch that operates from 37 to 49 GHz. It can handle an input power of up to 28 dBm, has an insertion loss of 1.4 dB, and provides an isolation of 30 dB. This switch exhibits high input linearity and is manufactured using a silicon process. It integrates a driver to perform logic functions internally and to provide users with the advantage of a simplified CMOS-/TTL control interfaces. This SPDT switch uses a single digitally controllable input pin at the driver IC to control the state of RF paths. Read more
Vector Network Analyzer from 10 MHz to 44 GHz for 5G Component Characterization
The E5081A ENA-X from Keysight is a Vector Network Analyzer (VNA) that operates from 10 MHz to 44 GHz. This VNA can accelerate 5G and satellite communication component characterization and perform flexible high-power tests with direct receiver access to integrate booster amplifiers, attenuators, or directional couplers. It combines various measurements into a single instrument and enables system characterization with faster speeds and greater flexibility, at a lower cost. This VNA has built-in low-noise receivers, and a configurable test set combined with modulated signal measurements that allow users to characterize high-performance components with a single connection. Read more
Radio Communication Test Station for 5G Test Requirements
The MT8000A from Anritsu is a Radio Communication Test Station for developing 5G communications terminals, chipsets and devices. This all-in-one desktop tester supports RF and protocol tests for the sub-6 GHz, including band n41 and millimeter wave bands. Combining it with the OTA Chamber enables both millimeter wave band RF measurements and beamforming tests using call connections specified by 3GPP. This platform provides flexible future-proof support for new 5G test requirements, including URLLC (Ultra-Reliable and Low Latency Communications) and mMTC (massive Machine Type Communications). Read more
4/7.5/13.6/30/44 GHz Signal and Spectrum Analyzers for 5G-NR Device Testing
The FSVA3000 from Rohde & Schwarz are Signal and Spectrum Analyzers that operate from 2 Hz to 4/7.5/13.6/30/44 GHz. They are designed to perform demanding signal analysis tasks and can help users set up complex measurements in the simplest and fastest way possible. These spectrum analyzers have an analysis bandwidth of up to 1 GHz and an SSB phase noise of –127 dBc/Hz @ 10 kHz offset. They are ideal for 5G NR signals and can simplify troubleshooting rare events while providing accurate and simplified measurement infrastructure. Read more
Compact Automated Tuner from DC to 65 GHz for 5G FR2 Applications
The NT-18G-50G-1C Nano5G Automated Impedance Tuner from Maury Microwave has been developed to conduct load pull measurements from 18 to 65 GHz. It supports 5G FR2 frequencies and provides a typical matching range with a VSWR up to 40:1 @ 28, 39 GHz. It can handle a CW power of 10 W and has an insertion loss of below 0.5 dB. The tuner has a direct probe connection that allows operation with no vibration and reduces the phase skew resulting in low signal distortion and more accurate vector measurements when using wideband modulated signals. It can also be mounted directly to the probe tip for on-wafer measurements, thereby ensuring the highest tuning range (VSWR, lowest impedance) at the DUT reference plane. Read more
4x24 Switch Matrix Series from 9 kHz to 26.5 GHz for 5G Testing
The SSM5000A Series from Siglent are Switch Matrices that operate from 9 kHz to 26.5 GHz. They can be configured to have up to 4 input ports with up to 24 output ports and an isolation of more than 65 dB. These switch matrices can handle an input power of 20 dBm and have a switching time of 10 μs. They can expand the number of test ports of a network analyzer, signal source, spectrum analyzer, or other equipment. These switch matrix products are suitable for use in multi-port test environments such as antennas and 5G component modules. Read more
Receiver Module from 32 to 38 GHz for Radar and 5G Applications
The SSR-3530633012-28-SE1 from ERAVANT is a Receiver Module that converts input frequencies (RF) from 32 – 38 GHz to output frequencies (IF) from DC – 18 GHz. It has a conversion gain of 12 dB with a noise figure of 3 dB. The receiver exhibits good gain flatness and includes a built-in x4 LO multiplier. It requires a DC supply of 8 V and consumes 300 mA of current. The SSR-3530633012-28-SE1 is available in a housing that measures 1.10 x 2.38 x 0.40 inches with a WR-28 uni-guide waveguide interface (with UG-599/U flange) and SMA-female LO/IF ports. It is ideal for radar systems and 5G applications. Read more
5G-NR Digital Repeater with 20/100 MHz Bandwidth
The SDRX-43-N77H from ADRF is a carrier-grade high-power 5G-NR Digital repeater for the upper C-Band spectrum. It is a cost-effective alternative to base stations, offering a quick and affordable means of delivering indoor and outdoor 5G coverage in metropolitan and rural areas. The SDRX-43-N77H can be individually wall-mounted or installed in an SDR-ICS chassis as a modular upgrade to existing infrastructure. The system can be configured and monitored remotely using a web-based graphical user interface (GUI), which provides access and monitoring to receive alarm notifications or make minor adjustments instantaneously. Read more
Outdoor Multi-Gigabit Radio from 71-76/81-86 GHz
The UltraLink-GX80 from Intracom Telecom is a compact all-outdoor Ethernet/CPRI Radio that operates from 71-76 GHz and 81-86 GHz. With a high system gain, it achieves a throughput of up to 10 Gbps (full duplex) which makes the radio suited for use in demanding applications requiring ultra-high capacity. It has channel sizes of 125/250/500/750/1,000/1,500/2,000 MHz. The radio is capable of adaptive modulation from 4-QAM to 1024-QAM and uses a LDPC/Reed Solomon error correction coding. Read more
Click here to visit 5G Hub on everything RF.
