Sponsored by Aeroflex / Inmet | |
|
 New RF & Microwave Products this Week |
|
|  | Frequency Doubler from Marki Microwave The MLD-1640 is a frequency doubler/multiplier with an input frequency range of 8 to 20 GHz and an output range of 16 to 40 GHz. This multiplier has been designed using a computer aided Microlithic design technique that increases the fundamental suppression by over 10 dB to a 33 dB suppression across the band. This level of suppression gives system designers more flexibility with filter requirements on their high frequency LO generation chains. It is available in a standard .152" x .090" Microlithic chip or connectorized package. Download Datasheet | Product Details
|
| | |
|
|  | Frequency Doubler from Hittite The HMC1105 is a frequency doubler MMIC from Hittite with an input frequency from 20-40 GHz. This frequency doubler is ideal for Point to Point, VSAT Radios, V Band communications, T&M, radar and space applications. It requires no DC bias and adds no measurable additive phase noise on to the multiplied signal. The HMC1105 is available as a die that measures 1.79 x 1.19 x 0.1 mm. Download Datasheet | Product Details
|
| | |
|
|  | Digital Attenuator from P1dB Inc. The P1-DA-6-6000MHz-0.5-63-SMA from P1dB Inc., is a USB powered Digital Attenuator that operates from 6 MHz to 6 GHz. This attenuator has an attenuation range of 63 dB with 0.5 dB steps and switching speed of 70 n sec. The P1-DA-6-6000MHz-0.5-63-SMA connects to a USB port for control and power and requires no additional DC supply voltage. Download Datasheet | Product Details
|
| | |
|
|  | Digital Phase Shifter from Telemakus The TEP2000-4 is a digital RF phase shifter for with a 360 degree phase range and a low insertion loss of 4 dB. It operates from 1 to 2 GHz and is powered by a USB Interface. The phase shifter can be controlled with a GUI on any windows based computer. It is a 12 bit phase shifter with a 0.25 degree resolution. The TEP2000-4 can handle up to 20 dBm of input power. Download Datasheet | Product Details
|
| | |
|
|  | Front End Module from Skyworks The SE5008L from Skyworks is a FEM with an integrated low noise amplifier and switch for WLAN chipsets at 5 GHz. The Low Noise Amplifier includes a bypass mode to avoid saturation in near-field applications. This FEM is ideal for use in Gaming Platforms. It is packaged in a compact 3 mm x 3 mm x 0.9 mm QFN package. The LNA output is matched to 50 ohms and all ports are DC blocked. Download Datasheet | Product Details
|
| | |
|
Sponsored by Aeroflex / Inmet |  | If a full hex attenuator better fits your specifications, look no further Aeroflex / Inmet is pleased to introduce a more user friendly version of our most popular 2W SMA attenuator; a full hex (FH) body configuration helps minimize the possibility of the attenuator rotating during installation by providing the technician with increased surface by which to secure the device. The same outstanding performance is now available in the Models 6FH (6GHz) and 18FH (18GHz). Standard attenuation values include 0-10, 12, 15, 20, 30 & 40dB. Similarly, our new FHC model is available for production volume 6GHz applications at slightly reduced electrical performance and lower cost. |
|
|
|  | RF Amplifier from Parsec Technologies, Inc. The M2M PT1233D from Parsec is a high performance low noise GaAs amplifier that operates from 50 to 2100 MHz. It provides a gain of 23.5 dB, an IP3 of 22.9 dBm and has a noise figure of 0.75 dB. It is ideal for GPS, Mobile TV, DAB, RKE, AMR, Cellular, LTE, Zigbee, SDARS, Wi-Fi and WYLAN Applications. This low noise amplifier requires a supply voltage of 3.3/5 V and is available in a 06-ETSLP package which measures 1.3 x 2.0 mm. It is matched to 50 Ohms. Download Datasheet | Product Details
|
| | |
|
|  | RF Amplifier from Hittite The HMC6741LS7 from Hittite is a high power amplifier with a temperature compensated power detector that operates from 9 to 12 GHz. It provides a gain of 35 dB, saturated output power of 28 dBm and has a 25% efficiency from a 7 V supply. The amplifier has a high IP3 making it ideal for high linearity military, commercial and space applications - Point to Point Radios, SATCOM, Marine Radar etc. It is available in a compact surface mount package and is matched to 50 Ohms. Download Datasheet | Product Details
|
| | |
|
|  | Bias Tee from Aeroflex - Inmet The 8800S are Bias Tees from Aeroflex/Inmet that operate from 10 MHz to 2.5 GHz, 6 GHz & 12 GHz. They can handle up to 100 V and 2.5 A. This series of bias tees has a low insertion loss of under 2 dB up to 12 GHz and a VSWR from 1.3:1 to 1.7:1 though the band. It can handle up to 5 W of RF power and is available with SMA Female/BNC Female Connectors for the RF port and solder posts for the dc connection. Download Datasheet | Product Details
|
| | |
|
|  | Bias Tee from RLC Electronics The BT-18A is a broadband bias tee from RLC Electronics that that operates from 0.5 to 18 GHz. It has an insertion loss of less than 1.5 dB and a VSWR of less than 1.6:1. The bias tee can handle up to 5 W of power and a DC current of up to 500 mA. It has a 50 V rating and has SMA Female connectors for both the RF signal and Bias input. Download Datasheet | Product Details
|
| | |
|
|  | RF Cable Assembly from Mini Circuits The 141-SMNB Series of Hand-Flex coaxial cables from Mini Circuits are ideal for integrating rack mounted coaxial components and sub-assemblies from DC to 12.5 GHz. The assembly has a N Type female at one end and a SMA connector at the other end. The outer shield of the cable is tin soaked copper braid which minimized signal leakage with high flexibility and a low loss PTFE dielectric. It is available in various lengths based on the application. Download Datasheet | Product Details
|
| | |
|
|  | Coaxial Termination from RF Industries The RFLOAD-NM50 is a 50 W low PIM termination from RF Industries. The RF load operates from DC to 3 GHz and a PIM of less than -110 dBc. It is available with N Type male connectors and is matched to 50 ohms with a VSWR of less than 1.2:1. The termination can handle a peak power of up to 500 W. Download Datasheet | Product Details
|
| | |
|
|  | Coaxial Termination from Pasternack Enterprises Inc The PE6214 is a 50 W RF Load that operates from DC to 18 GHz. It is matched to 50 Ohms, has N Type Female connectors and a VSWR of 1.3:1 to 1.6:1 over the frequency band. The termination can handle up to 500 W of peak power and can operate at a temperature range from -65 to 125 Degrees C. Download Datasheet | Product Details
|
| | |
|
|  | Between Series Coaxial Adapter from Fairview Microwave The SM8226 is a 4.1/9.5 Male Mini-DIN to N Type Female low PIM adapter which operates from DC to 6 GHz with a VSWR of less than 1.25:1 through the band. The adapter has a low PIM of -160 dBc using 2 CW tones @ 20W/tone. The adapter is constructed with tri-alloy plated brass bodies and silver plated Beryllium Copper (BeCu) center contacts, allowing low IMD and low attenuation. Download Datasheet | Product Details
|
| | |
|
|  | Directional Coupler from AtlanTecRF The AKC Series of Directional Couplers from AtlanTecRF operate from 1-40 GHz with a high directivity of 10 dB and low insertion loss of less than 2.5 dB. The couplers have a VSWR from 1.5:1 to 1.8:1 depending on the configuration and can handle up to 30 W of input power. They are available in a connectorized module with 2.92mm Stainless Steel connectors and are matched to 50 Ohms. Download Datasheet | Product Details
|
| | |
|
