1. everything RF
  2. RF Newsletters
more
PREV 24 June, 2020 NEXT

New RF and Microwave Products this Week

24 June, 2020 - everything RF Newsletter

New products this week. View it in your browser

 
Date: 24 June, 2020
 
Sponsored by Amphenol SV Microwave
 
 
 
New RF and Microwave Products this Week
Front End Module
6 to 18 GHz Front-End IC for Phased Array Antennas and Radar Applications

Front End Module  from Analog Devices

The ADTR1107 from Analog Devices is a Front-End IC that operates from 6 to 18 GHz. It has an integrated power amplifier, low noise amplifier (LNA), and a reflective SPDT switch. In Tx mode, it delivers a saturated output power of 25 dBm with a small signal gain of 22 dB. Whereas, in the Rx mode, it provides a small signal gain of 18 dB with a noise figure of 2.5 dB.
Download Datasheet | Product Details
Front End Module
5 GHz Wi-Fi Front-End Module for IEEE 802.11a/n/ac systems

Front End Module  from Microchip Technology

The LX5589A from Microchip Technologies is a complete Wi-Fi Front End Module (FEM) that supports IEEE 802.11a/n/ac systems. It includes a highly linear 5 GHz Power Amplifier (PA) with a power detector, Low Noise Amplifier (LNA) with bypass capability, and an SPDT antenna switch. On the Tx side, the module provides a saturated output power of 17 dBm and has a gain of 30 dB.
Download Datasheet | Product Details
Band Pass Filter
Thin-Film Band Pass Filter from 4120 to 4520 MHz

Band Pass Filter  from AVX Corporation

The BP0805A4320ASTR from AVX Corporation is a Band Pass filter that has a passband from 4120 to 4520 MHz with center frequency at 4320 MHz. It is ideal for Base Stations, Mobile communications, Satellite TV receivers, GPS, Vehicle location systems, and Wireless LAN’s applications.
Download Datasheet | Product Details
RF Amplifier
2 W GaN Power Amplifier from 8.5 to 10.5 GHz

RF Amplifier  from Qorvo

The QPA2610 from Qorvo is an X-Band GaN power amplifier that operates from 8.5 to 10.5 GHz. It provides more than 2 W (33 dBm) of saturated output power with a small signal gain of 38.5 dB and power added efficiency of up to 47%. The amplifier has an input return loss of 19 dB and an output return loss of 14 dB.
Download Datasheet | Product Details
RF Variable Attenuator
USB/Ethernet Controlled 8-Channel Attenuator from 50 MHz to 8 GHz

RF Variable Attenuator  from Adaura Technologies

The AD-USB8AR38G95 from ADAURA Technologies is an eight-channel programmable attenuator that operates from 50 MHz to 8 GHz. It has an attenuation range from 0 to 95 dB with a step size of 0.25 dB, interchain isolation of over 100 dB, and can handle an input power of up to 31 dBm. This attenuator has an insertion loss of less than 10.8 dB and has a switching speed of 520 ns.
Download Datasheet | Product Details
Vector Network Analyzer
6 GHz, 1-Port USB Vector Network Analyzer

Vector Network Analyzer  from Copper Mountain Technologies

The R60 is a single port USB-powered VNA (Reflectometer) capable of measuring S11 from 1 MHz to 6.0 GHz. It can be operated from any Windows PC or laptop using a USB cable. Applications of the R60 include antenna matching, cable and connector quality control, antenna production quality assurance, field testing and troubleshooting of cables, material measurements, and many others.
Download Datasheet | Product Details
Signal Generator
40 GHz Multi-Channel RF Synthesizers

Signal Generator  from Holzworth Instrumentation

The HSX Series are broadband, phase coherent frequency sources that are available in five frequency configurations from 10 MHz to 3 GHz, 6 GHz, 12 GHz, 24 GHz and 40 GHz. They have industry leading phase noise and spectral purity performance coupled with a highly accurate dynamic range from -110 to 20dBm. They are available in 1, 2, 3 or 4 channel Custom COTS models that can be ordered with any combination of frequency options.
Download Datasheet | Product Details
Sponsored by Amphenol SV Microwave
PCB Multiport Connectors
PCB Multiport Connectors
Amphenol SV Microwave’s high performance RF/coaxial SMPM & SMPS multiport PCB connectors are ideal for high frequency printed circuit board applications where precision is key. These connectors enable extremely high frequencies (DC up to 100 GHz) while maintaining the smallest form factor. Click here to learn more.
 
RF Switch
SP6T Absorptive Switch from 100 MHz to 18 GHz

RF Switch  from UMCC

The SR-V070-6S from UMCC is an absorptive SP6T switch that operates from 100 MHz to 18 GHz with 6-Bit binary control and an integral TTL driver. This PIN Diode switch has an insertion loss of less than 4 dB and isolation of more than 75 dB. It can handle up to 24 dBm of CW power and has a switching speed of 150 ns.
Download Datasheet | Product Details
180 Degree Hybrid Coupler
180-degree Hybrid Power Combiner/Divider from 350 to 1000 MHz

180 Degree Hybrid Coupler  from Werlatone Inc

The H9395 from Werlatone is a 180-degree Hybrid Power Combiner/Divider that operates from 350 to 1000 MHz. It can handle up to 250 W of CW input power while providing isolation of 20 dB. The device has an insertion loss of less than 0.3 dB and a VSWR of 1.3:1. It has a phase balance of 180 degrees and an amplitude balance of 0.4 dB.
Download Datasheet | Product Details
RF Cable
50 GHz Rugged RF Cable with Internally Armored GrooveTube Technology

RF Cable  from MegaPhase

The Warrior cable from MegaPhase is an Ultra-rugged RF Cable with internally armored GrooveTube technology that operates from 0.3 to 50 GHz. The cable can withstand rugged field handling in extreme operating conditions associated with electronic countermeasures, electronic warfare, and multiple types of field-deployed communication systems.
Download Datasheet | Product Details
RF Amplifier
50 MHz to 3 GHz GaN MMIC Power Amplifier

RF Amplifier  from AMCOM Communications, Inc.

The AM003042WN-XX from AMCOM Communications is a GaN MMIC Power Amplifier that operates from 50 MHz to 3 GHz. The amplifier provides a saturated output power of 42 dBm, P1dB of 38 dBm and a small signal gain of 23 dB. It requires a 40 V DC supply and consumes 500 mA of current. The MMIC amplifier is matched to 50 Ohms at the input but un-matched at the output above 2 GHz.
Download Datasheet | Product Details
RF Amplifier
C-Band Solid State Bi-directional Amplifier from 4.4 to 5.1 GHz

RF Amplifier  from NuWaves Engineering

The NW-BA-C-10-RX03 from NuWaves is a C-Band Solid State Bi-directional Amplifier module that operates from 4.4 to 5.1 GHz. The BDA has an auto-sense transmit/receive (T/R) control, with an extremely fast T/R mode switch time of under 2 uS. In Tx mode, it provides an output power of up to 10 watts with a gain of 12 dB and a power efficiency of 20%.
Download Datasheet | Product Details
RF Amplifier
15 dB K-Band Amplifier from 18 to 26.5 GHz

RF Amplifier  from Farran Technology

The FLNA-42-15 from Farran Technology is a Low Noise MMIC Amplifier that operates from 18 to 26.5 GHz. It provides a gain of 15 dB and has a noise figure of 3 dB. This K-Band amplifier has a VSWR of 2:1 and requires an 8 VDC supply while consuming 100 mA of current. It is available in a compact module with coaxial connectors.
Download Datasheet | Product Details
RF Amplifier
10 W RF Amplifier from 500 to 2500 MHz

RF Amplifier  from RFcore

The RCA0525H40B0 from RFCore is an RF Amplifier that operates from 500 to 2500 MHz. It provides more than 10 W of CW saturated output power with a small signal gain of 44 dB (5 dB gain flatness) and has a switching time of 10 µs. The device can handle up to 10 dBm of short-term and 5 dBm of long-term input power. It has a load VSWR of 3.5:1.
Download Datasheet | Product Details
Sponsored by Amphenol SV Microwave
RF PCB Edge Connectors
Extreme RF PCB Edge Connectors with Legs
Amphenol SV Microwave offers a complete line of extreme frequency (DC - 50 GHz) coaxial / RF edge launch PCB connectors with through hole legs for high mating cycles. These high speed RF test connector configurations include SV's high frequency 2.92 mm, 2.4 mm and SMA series and meet the need for high performing, highly reliable precision connectors. Pre-tinned versions allow for fast and easy soldering during installation onto the PCB. These connectors are ideal for the 5G wireless development applications. Click here to learn more.
 
Antenna
Rigid Fiberglass Adhesive Mount Antenna for 5G-NR Applications

Antenna  from 2J Antennas

The 2JP0383P from 2J Antennas is a Rigid Fiberglass Adhesive Mount Antenna for 5G-NR that operates in 4 bands (617-960, 1427-2690, 3300-5000, 5150-5925 MHz). This antenna supports 5G-NR, 4G/LTE, FirstNet, CBRS, LPWA, CAT-X, CAT-Mx, CAT-NBx, NB-IoT, 3G, and 2G standards. It delivers a peak gain of over 1.4 dBi with an efficiency of up to 60.8% and can handle an input power of up to 25 watts.
Download Datasheet | Product Details
RF Module
Nano Sim-Size Bluetooth 5.1 Module

RF Module  from Wurth Elektronik

The 2611011024000 (Proteus-III) from Wurth Elektronik is a BLE V 5.1 RF Module with a data rate of 2 Mbps. It is based on the Nordic nRF52840 chipset and has a payload size of 964 bytes. The module has a Tx output power of 6 dBm and has a receiver sensitivity of -92 dBm. It requires a 3.6V DC supply and has a current consumption of 18.9 mA when transmitting and 7.7 mA when receiving.
Download Datasheet | Product Details
RF Module
Wi-Fi / Bluetooth 5.0 Module for IoT and Consumer Electronic Applications

RF Module  from Redpine Signals

The RS9116 from Redpine Signals is a Single-Band Multi-Protocol Wireless Module for 802.11 b/g/n (2.4GHz), 802.11j, and dual-mode Bluetooth 5.0. It supports 20 MHz and 40 MHz Wi-Fi channel bandwidths and has a transmitting power of up to 18 dBm (Wi-Fi) and 16 dBm (Bluetooth) with an integrated PA. The module offers high throughput and an extended range with power-optimized performance.
Download Datasheet | Product Details
RF Module
LoRa Modules from 860 to 1020 MHz

RF Module  from Miromico

The FMLR-72-x-STL0Z from Miromico are LoRa modules that operate from 860 to 1020 MHz. These LoRa modules can enable wireless connectivity to almost all devices, systems and sensors communicating at a low data rate over a distance of more than 50 km. They are available with an antenna pad or UFL Connector.
Download Datasheet | Product Details
RF Switch
Reflective SPDT Switch from DC to 26.5 GHz

RF Switch  from Atlanta Micro

The AM6016 from Atlanta Micro is a reflective SPDT switch that operates from DC to 26.5 GHz. It has an insertion loss of 1.2 dB and provides isolation of more than 30 dB. The switch has an Input IP3 of 40 dBm and requires a DC Supply from 3.3 to 5V. It requires a single positive supply and a single positive control voltage to switch between the two paths.
Download Datasheet | Product Details
Power Divider
30 W, 2 Way Power Divider from 698 to 2700 MHz

Power Divider  from VidaRF

The VPD-0627A2 from VidaRF is a 2 way RF power divider that operates from 0.698 to 2.7 GHz for all wireless applications from cellular through UMTS. It can handle up to 30 Watts of power, has an insertion loss of less than 0.5 dB and provides isolation of more than 20 dB. The power divider is available with SMA connector.
Download Datasheet | Product Details
Dual Directional Coupler
10 dB Dual Directional Coupler from 7 to 12.4 GHz

Dual Directional Coupler  from MECA

The 785-10-9.700 from MECA is a dual directional coupler that operates from 7 to 12.4 GHz. It provides a coupling of 10 dB (1.25 dB coupling deviation) with directivity of more than 16 dB and an insertion loss of 0.9 dB. The coupler can handle up to 50 W of average power and 3 kW of peak power. It has a VSWR of 1.35:1.
Download Datasheet | Product Details
RF Shielded Test Enclosure
RF Shielded Test Box for EMC Testing from 20 MHz to 6 GHz

RF Shielded Test Enclosure  from RF Electronics

The HDRF-6U60-B1 from RF Electronics is an RF Shielded Test Box that operates from 20 MHz to 6 GHz. It has a thick RF absorbing foam that provides isolation of more than 130 dB which attenuates standing waves and reflections. The RF Test box is equipped with shielded power filters for power connections in the box while still blocking all wireless signals.
Download Datasheet | Product Details
RF Cable Assembly
DC to 26.5 GHz Cable Assembly with 1 psec Phase Match

RF Cable Assembly  from P1dB Inc.

The P1CA-SAMSAM-F140-36-PM-1PS from P1dB is an SMA Male to SMA Male Flexible Cable Assembly that operates from DC to 26.5 GHz. This phase-matched cable assembly has an insertion loss of 1.65 dB, a VSWR of less than 1.30:1, and a bend radius of 0.7 inches. The assembly utilizes F140 coaxial cables which are 0.142 inches (3.6mm) in diameter and 36 inches in length.
Download Datasheet | Product Details
Antenna
120 Degree Sector Antenna from 2 to 2.7 GHz

Antenna  from MP Antenna

The 08-ANT-0867 from MP Antenna is a 120 Degree Sector Antenna that operates from 2 to 2.7 GHz. This Directional antenna delivers a gain of 10 dBi and can handle 50 watts of input power. The multi-polarized antenna is constructed of UV stabilized polymers and high-grade aluminum for extremely long service life in the most demanding conditions.
Download Datasheet | Product Details
About everything RF
everything RF keeps users up to date with the RF & Microwave Industry. This product update newsletter consists of the latest RF & Microwave products from the leading companies in the Industry.
To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]