1. everything RF
  2. RF Newsletters
more
PREV 27 Oct, 2021 NEXT

New RF and Microwave Products this Week

27 Oct, 2021 - everything RF Newsletter

New products this week. View it in your browser

 
Date: 27 Oct, 2021
 
Sponsored by SV Microwave
 
 
 
New Products this Week
Antenna Measurement System
Compact Anechoic Chamber for mmWave 5G and Radar Applications

Antenna Measurement System  from Milliwave Silicon Solutions

The MBX33-G4-380 from Milliwave Silicon Solutions is a compact anechoic chamber test setup that fits on a lab bench. The combination of the MBX33 (chamber) with GIM04-380 (antenna positioner) gives 2m of Far-Field distance, 50cm on the internal cavity, and a 3-Axis mmWave 3D antenna positioner supporting a DUT width of 38cm. This is perfect for the characterization of mmWave Radar, 5G phased array antennas and systems.
Download Datasheet | Product Details
RF Spectrum Analyzer
Microwave Measurement Receiver from 2 Hz to 8/26.5/50 GHz

RF Spectrum Analyzer  from Rohde & Schwarz

The FSMR3000 from Rohde & Schwarz is a Microwave Measurement Receiver that operates from 2 Hz to 8/26.5/50 GHz. It has been developed to calibrate signal generators and attenuators. The receiver provides tuned RF level measurements, level measurements, analog/frequency/phase modulations, and spectrum analysis. This calibration/verification device can measure power levels from -152 to 30 dBm.
Download Datasheet | Product Details
Front End Module
Wi-Fi 6 (802.11ax) Front End Module from 5150 to 5850 MHz

Front End Module  from Qorvo

The QPF4526 from Qorvo is a Front-End Module that operates from 5150 to 5850 MHz and is designed for Wi-Fi 6 (802.11ax) systems. It integrates a 5 GHz power amplifier (PA), single pole two throw (SP2T) switch and a bypassable low noise amplifier (LNA) into a compact form factor to minimize layout area on boards. It provides a transmit gain of 33 dB, a receive gain of 14.5 dB and has a noise figure of less than 1.9 dB.
Download Datasheet | Product Details
Fixed Attenuator
Thin Film Bandpass Filters for UWB Applications

Fixed Attenuator  from KYOCERA AVX

The BP Series from KYOCERA AVX are Thin Film Bandpass Filters with a passband from 800 to 6670 MHz. They offer low insertion loss, high out of band rejection, steep roll-off, high repeatability, and high-temperature stability. The filters are based on thin-film multi-layer technology which provides a miniature part with excellent high-frequency performance and rugged construction for reliable automatic assembly.
Download Datasheet | Product Details
Power Sensor
Real-Time True Average Power Sensor from 10 MHz to 18 GHz

Power Sensor  from Boonton

The RTP4018 from Boonton is a Real-Time True Average Power Sensor that operates from 10 MHz to 18 GHz. It has an average dynamic range from -60 to +20 dBm and a continuous sampling rate of 25 MHz. The sensor uses Real-Time Power Processing (RTPP) technology which is a unique parallel processing methodology that performs power measurement at unmatched speeds.
Download Datasheet | Product Details
Vector Network Analyzer
Compact USB VNA from 20 kHz to 3.0 GHz

Vector Network Analyzer  from Copper Mountain Technologies

The S7530 is a 75 Ohm 2 Port compact VNA that operates up to 3 GHz. It has a wide dynamic range and can be operated with any Windows PC or laptop. Its small size makes it easy to carry around to test sites or to share within a team. In addition to S parameters (S11, S12, S21, S22) this VNA has a variety of analysis capabilities, including time-domain with gating and frequency offset modes.
Download Datasheet | Product Details
Sponsored by SV Microwave
Edge Lock RF PCB Connectors
Edge Lock RF PCB Connectors
SV’s newest PCB connector series forms a secure fit between the connector and the PCB edge without the use of a fixture and ensures optimal RF performance throughout the connector’s full frequency range. Available in 2.92mm and SMA series and in stock through distribution now! Click here to learn more.
 
RF Variable Attenuator
12-Channel Programmable Attenuator Assembly from 50 MHz to 8 GHz

RF Variable Attenuator  from Adaura Technologies

The AD-12AR38G95 from Adaura Technologies is a Programmable Attenuator Assembly that operates from 50 MHz to 8 GHz. It has 12 individually controlled attenuators that provide an attenuation range from 0-95 dB in 0.25 dB steps with a transition time of 425 ns. The solid-state attenuator system has an insertion loss of less than 12 dB and provides more than 110 dB of isolation.
Download Datasheet | Product Details
RF Variable Attenuator
Solid State USB Programmable Attenuator from 30 to 3000 MHz

RF Variable Attenuator  from JFW Industries

The 50P-2042 from JFW Industries is a solid state programmable attenuator that operates from 30 MHz to 3 GHz. It has an attenuation range from 0 to 63.5 dB with 0.5 dB steps. The attenuator has a fast switching speed of 1 micro second and can handle an input power of up to 20 dBm. It is available in a module with SMA female connectors and a USB port for power/control.
Download Datasheet | Product Details
RF Amplifier
11 W Solid State GaN Power Amplifier from 1435 to 1525 MHz

RF Amplifier  from NuWaves Engineering

The NuPower 12B01A-03 from NuWaves Engineering is an L-band Solid State GaN Power Amplifier that operates from 1435 to 1525 MHz. It delivers an output power of more than 11 W with a small signal gain of up to 49.5 dB. It has been developed to boost the performance of data links and transmitters. The amplifier utilizes high-efficiency GaN technology and provides 30% efficiency.
Download Datasheet | Product Details
RF Amplifier
10 W Solid State Power Amplifier from 18 to 40 GHz

RF Amplifier  from Exodus Advanced Communications

The AMP4037DB-1LC from Exodus Advanced Communications is a Solid-State Power Amplifier that operates from 18 to 40 GHz (Band A: 18 to 26.5 GHz; Band B: 26.5 to 40 GHz). It provides a saturated output power of more than 10 W with a gain of over 40 dB in both bands. The amplifier system is built using high-power advanced technology devices and has a class A/AB linear design.
Download Datasheet | Product Details
RF Amplifier
120 W Pulsed TWT Amplifier from 26.5 to 40.0 GHz

RF Amplifier  from ETS-Lindgren

The 8100-083 from ETS-Lindgren is a Pulsed TWT Amplifier that operates from 26.5 to 40.0 GHz. It delivers an output power of more than 120 W, has a gain variation of 6 dB, and a VSWR of less than 2:1. The amplifier provides higher linearity and better efficiency compared to Silicon-based amplifiers and is designed primarily for EMC applications.
Download Datasheet | Product Details
RF Amplifier
Rugged Low Noise Amplifier from 10.7 to 12.8 GHz

RF Amplifier  from AmpliTech

The APTW5-10701280-40K10-WR75-D6 from AmpliTech is a Low Noise Amplifier that operates from 10.7 to 12.8 GHz. It provides 42 dB of gain with a noise temperature less than 40 K and has a P1dB of 15 dBm. The LNA uses state-of-the-art PHEMT technology with a no-isolator design and is MIL-883 and MIL-45208 certified for reliable performance.
Download Datasheet | Product Details
Sponsored by SV Microwave
 
 
 
RF Variable Attenuator
60 dB Analog PIN Diode Attenuator from 6 to 12 GHz

RF Variable Attenuator  from Planar Monolithics Industries

The PVVAN-6012-60-MP from Planar Monolithics Industries is a PIN Diode Attenuator that operates from 6 to 12 GHz. It has an attenuation range of 60 dB and can be controlled at 10 dB/V via an analog interface. This attenuator can handle an RF power of up to 30 dB and has an insertion loss of less than 2.8 dB. It requires a power supply from +12 to +15 V/-12 to -15 V and consumes under 125 mA.
Download Datasheet | Product Details
Software
3D EM Simulation Software for High-Fidelity Computations

Software  from Remcom

XFdtd is a full-wave 3D EM solver that simplifies the analysis of complex EM problems and leads the market in FDTD-based modeling and simulation. With unrivaled speed, XF is the leader for complex, high-fidelity EM simulations. Applications include microwave devices such as waveguides, power dividers, and filters; antenna design and placement; EMI/EMC testing; static discharge; signal integrity; SAR validation; radar and scattering and photonics.
Download Datasheet | Product Details
RF Cable Assembly
Low Smoke Cable Assemblies from DC to 38 GHz

RF Cable Assembly  from Times Microwave Systems

The PhaseTrack Low Smoke (PTLS) Series from Times Microwave Systems are Cable Assemblies that operate from DC to 38 GHz. Low smoke, zero halogen cable assemblies are essential in confined spaces where air exchange is minimal such as onboard ships and submarines. Fire is one of the greatest dangers in these environments, as accumulating smoke can obscure visibility for safe evacuation.
Download Datasheet | Product Details
Band Pass Filter
Band Pass Filter with Passband from 27.5 to 29.5 GHz for 5G Applications

Band Pass Filter  from Mini Circuits

The BFCQ-2802+ from Mini Circuits is a Bandpass Filter with a passband from 27.5 to 29.5 GHz and a center frequency of 28.4 GHz. It has an insertion loss of less than 3.4 dB in the passband and provides over 20 dB attenuation in the stopband. The filter utilizes a proprietary LTCC material and a distributed filter topology which enables this filter to achieve repeatable performance on a lot-to-lot basis for mmWave frequencies.
Download Datasheet | Product Details
Directional Coupler
30 W Directional Coupler from 130 to 520 MHz

Directional Coupler  from Werbel Microwave

The C-1352-03 from Werbel Microwave is a Directional Coupler that operates from 130 to 520 MHz. It has a coupling factor of 3.5 dB with directivity of 25 dB. This 50-ohm coupler can handle an input RF power of 30 W, reverse power of up to 3 W, and has a VSWR of less than 1.30:1. It is available in a RoHS and REACH compliant module that measures 5.80 x 1.74 x 1.00 inches and has SMA-female connectors.
Download Datasheet | Product Details
Bi-Directional Coupler
30 W Bi-Directional Coupler from 20 to 550 MHz

Bi-Directional Coupler  from Synergy Microwave Corporation

The SDCHP-255 from Synergy Microwave Corp is a Bi-Directional Coupler that operates from 20 to 550 MHz. It has a coupling factor of 20 dB with more than 20 dB directivity. This coupler can handle up to 30 W of RF input power and has a VSWR of less than 1.30:1. It is available in a RoHS-compliant surface-mount package that measures 0.50 x 0.37 inches and is ideal for antenna signal monitoring applications.
Download Datasheet | Product Details
Power Divider
4-Way Power Divider from 1 to 18 GHz

Power Divider  from VidaRF

The VPD10180A4 from VidaRF is a 4-way Power Divider that operates from 1 to 18 GHz. This divider has an insertion loss of 2.9 dB and an isolation of over 15 dB. It has an amplitude balance of ±0.8 dB and a phase balance of ±10 degrees. The divider is available in a module with coaxial connectors.
Download Datasheet | Product Details
Termination
1 W Resistive Termination from DC to 30 GHz

Termination  from RD Microwaves

The TA-1SM-HP from RD Microwaves is a Resistive Termination that operates from DC to 30 GHz. It can handle an average power of 1 W CW, a peak power of up to 1 kW, and has a VSWR of less than 1.18:1. This termination is impedance-matched to 50 Ohm and exhibits minimal reflection characteristics. It is available in a passivated stainless-steel body with an SMA-Male interface.
Download Datasheet | Product Details
Waveguide Circulator
Low Power Space Qualified Waveguide Circulator from 18 to 20 GHz

Waveguide Circulator  from Smiths Interconnect

The 19CD328 from Smiths Interconnect is a Waveguide Circulator that operates from 18 to 20 GHz. It can handle a CW input power of 2 W, has an insertion loss of less than 0.15 dB, and provides more than 23 dB of isolation. The circulator has been specifically designed for waveguide demultiplexers (channel droppers) and is arranged mechanically to be cascaded to suit the number of channels required.
Download Datasheet | Product Details
Diplexer
2.4/5-7 GHz Mini Passive RF Diplexer for Wi-Fi Applications

Diplexer  from Johanson Technology

The 2450DP14A6000 from Johanson Technology is a Mini Passive RF Diplexer with passbands from 2.4 to 2.5 GHz (Low Band) and 4.9 to 7.15 GHz (High Band). It provides more than 25 dB of attenuation above and below the bands. This diplexer can handle a CW input power of 3 W and has an insertion loss of less than 1.5 dB. It is available in an EIA 0603 package that measures 1.6 x 0.8 mm with an LPF/BPF filtering scheme.
Download Datasheet | Product Details
RF Amplifier
Low Noise Amplifier from 1.4 to 2.7 GHz for LTE and 5G Applications

RF Amplifier  from Infineon Technologies

The BGA9H1MN9 from Infineon Technologies is a Low Noise Amplifier designed for LTE and 5G applications from 1.4 to 2.7 GHz. It provides 20.2 dB of gain, has a noise figure of 0.6 dB, and has high EMI robustness. The LNA features gain steps that allow the gain and linearity to be adjusted to enhance the system dynamic range and accommodate varying interference scenarios.
Download Datasheet | Product Details
RF Module
Standalone Bluetooth 5.1 LE Module for High-Temperature Applications

RF Module  from u-blox AG

The ANNA-B412 from u-blox is a Standalone Bluetooth 5.1 LE Module for harsh industrial and lighting applications. It provides a throughput of 800 Kbps and supports up to 8 simultaneous connections. The module has an internal chip antenna for easy integration into end-products as well as an antenna pin for use with an external antenna of choice.
Download Datasheet | Product Details
Antenna
Ceiling-Mounted 5G NR/4G LTE DAS Antenna from 617 to 4200 MHz

Antenna  from Pulse Electronics

The DASLPP5G4310 from Pulse Electronics is a 5G NR/4G LTE Multi-Dipole DAS Antenna that operates from 617 to 4200 MHz. This horizontally polarized antenna provides more than 2 dBi of gain and has an average efficiency of 75%. It has an omnidirectional radiation pattern with a VSWR of 1.5:1 and a PIM of -152 dBc. It is suitable for use in buildings, DAS 4G LTE/5G systems, and ceiling mount applications.
Download Datasheet | Product Details
About everything RF
everything RF keeps users up to date with the RF & Microwave Industry. We provide the latest news, information on new product releases, upcoming events, white papers, articles and much more.
To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]