1. everything RF
  2. RF Newsletters
more
PREV 20 April, 2022 NEXT

New RF and Microwave Products this Week

20 April, 2022 Newsletter - everything RF

New products this week. View it in your browser

 
Weekly Edition
Date: 20 April, 2022
 
Sponsored by Rohde & Schwarz
 
 
New RF and Microwave Products this Week
RF Switch
MEMS-Based SP4T Switch from DC to 6 GHz
RF Switch  from Menlo Micro

The MM5140 from Menlo Micro is a MEMS SP4T Switch that operates from DC to 6 GHz. It can handle a CW input power of 25 W and a peak input power of 150 W. The switch has a turn-on time of 8.5 µs and a turn-off time of 2.5 µs. It has an insertion loss of 0.4 dB and provides isolation of more than 26 dB. This switch is built on Menlo Micro's Ideal Switch technology and utilizes an integrated charge pump/driver circuit.
Download Datasheet Product Details
RF Mixer
RF Mixer from 10 to 1500 MHz
RF Mixer  from Teledyne Microwave Solutions

The MC1502 from Teledyne Microwave Solutions is an RF Mixer with an RF/LO frequency from 10 to 1500 MHz and an IF frequency from DC to 1000 MHz. It has a conversion loss of less than 9.5 dB, provides an LO to RF isolation of more than 25 dB and an LO to IF isolation of over 14 dB. This mixer is available in a TO-8, TO-8H, or surface mount package.
Download Datasheet Product Details
RF Variable Attenuator
10 dB Temperature Variable Attenuators from DC to 12.4 GHz
RF Variable Attenuator  from Smiths Interconnect

The HCM Series from Smiths Interconnect are Temperature Variable Attenuators that operate from DC to 12.4 GHz. They are available in attenuation levels from 0 to 10 dB in step sizes of 1 dB and can handle a CW input power of up to 200 mW. These fixed chip attenuators have a VSWR of less than 1.30:1 and have a temperature coefficient of attenuation from -0.009 to -0.003 dB/dB/°C.
Download Datasheet Product Details
Fixed Attenuator
10 dB Surface-Mount Attenuator MMIC from DC to 50 GHz
Fixed Attenuator  from Marki Microwave

The ATN10-0050CSP1 from Marki Microwave is an Attenuator MMIC that operates from DC to 50 GHz. It can handle an input power of 1 W, provides an attenuation of 10 dB, and has an insertion loss of less than 10 dB. This GaAs MMIC is available in a surface-mount chip-scale package (CSP) that measures 1.5 x 1.5 x 0.9 mm and is suitable for 5G, amplitude matching, test equipment, high channel count systems, and airborne applications.
Download Datasheet Product Details
Noise Source
Waveguide Noise Sources 26.5 to 110 GHz
Noise Source  from NoiseWave

The NW-W Series from NoiseWave are Noise Sources that operate from 26.5 to 110 GHz. They provide an excess noise ratio (ENR) of more than 15 dB and have VSWR of less than 1.6:1. These noise sources use millimeter-wave noise diodes that are screened for superior noise characteristics, and a microstrip antenna approach which makes them more stable and significantly more reliable.
Download Datasheet Product Details
Wireless SoC
Wi-Fi 7 + Dual-Core Bluetooth Chipset for Mobile Handsets
Wireless SoC  from Broadcom

The BCM4398 from Broadcom is a Wi-Fi 7 and Bluetooth 5.2 Combo Chipset that operates from 5 to 7 GHz. This low-power, highly integrated Wi-Fi 7 and Bluetooth 5.2 combo chip is optimized for mobile handset applications where high performance, low latency, low power consumption, and small solution size are key requirements.
Download Datasheet Product Details
Sponsored by Rohde & Schwarz
Rohde & Schwarz
R&S®CMP200 – fine-tuned for ultra-wideband
Watch our video and discover how an OTA test setup featuring the R&S®CMP200 allows performing all cases important for UWB testing: time of flight, angle of arrival as well as transmitter and receiver performance. Click here to learn more.
RF Module
LoRa Edge™ Transceiver for Multi-Band Worldwide Asset Management
RF Module  from Semtech

The LR1120 from Semtech is a Multi-Band LoRa Edge Transceiver that supports Long Range - Frequency Hopping Spread Spectrum (LR-FHSS) communication over 150-960 MHz (sub-GHz) and 2.4 GHz ISM bands as well as licensed S-Band for satellites. It complies with LoRa Alliance’s LoRaWAN specifications and has a multi-constellation GNSS scanner and a passive Wi-Fi Access Point address scanner.
Download Datasheet Product Details
Vector Network Analyzer
2-Port USB Vector Network Analyzer from 1 MHz to 6.5 GHz
Vector Network Analyzer  from Sanko Technologies

The BN100 from Sanko Technologies is a 2-Port USB Controlled Vector Network Analyzer that operates from 1 MHz to 6.5 GHz. It offers a wide dynamic range, low noise level, and high resolution scanning with laboratory and research-grade performance. The VNA has a dynamic range of 121 dB and a noise level of less than -120 dBm. It supports 10001 measurement points at a speed of 120 µs/point.
Download Datasheet Product Details
Radar Sensor
FMCW/CW Radar Transceiver from 119.3 to 125.8 GHz
Radar Sensor  from Silicon Radar GmbH

The TRX_120_001 from Silicon Radar is a Radar Transceiver that operates from 119.3 to 125.8 GHz. It supports FMCW/CW modes and can be used for distance and speed measurement of objects using analog signals. This transceiver converts high-frequency radar signals to smaller analog signals with a maximum frequency of 2 GHz.
Download Datasheet Product Details
RF Transistor
500 W GaN HEMT from 2.9 to 3.5 GHz for S-Band Radar Systems
RF Transistor  from Wolfspeed, A Cree Company

The CGHV35400F1 from Wolfspeed is a GaN HEMT that operates from 2.9 to 3.5 GHz for S-band radar systems. It provides up to 500 W (57.1 dBm) of pulsed output power with a power gain of 11.1 dB and drain efficiency of up to 69%. The GaN HEMT has a duty cycle of 20% with 2 ms pulse lengths. It is matched to 50 ohms and is ideal for civil and military pulsed radar amplifiers.
Download Datasheet Product Details
RF Amplifier
700 W Solid-State Power Amplifier from 10 kHz to 250 MHz
RF Amplifier  from Exodus Advanced Communications

The AMP2080D from Exodus Advanced Communications is a Solid-State Power Amplifier that operates from 10 kHz to 250 MHz. It delivers a CW output power of 700 W with more than 57 dB of gain. This Class A/AB linear amplifier has spurious levels of less than -60 dBc and harmonics of -20 dBc. It is equipped with built-in protection circuits with extensive monitoring parameters for forward/reflected power in Watts & dBm, VSWR, voltage, current and temperature. The amplifier also features Exodus’ quiet-cool technology for closed-circuit air-liquid cooling.
Download Datasheet Product Details
Between Series RF Adapter
Triaxial Adapters for Medical Applications
Between Series RF Adapter  from IntelliConnect

The Triaxial Adapters from Intelliconnect are designed for use in medical industries for radiation detection equipment and medical imaging. They use a non-constant impedance design with an isolated ground and are readily available in BNC, TNC, and other configurations. These adaptors are also used in broadcast and camera applications where reduced ‘noise’ or interference levels are required.
Download Datasheet Product Details
Sponsored by Rohde & Schwarz
 
 
RF Amplifier
Low Noise Amplifier from 1 to 2 GHz
RF Amplifier  from Planar Monolithics Industries

The PEC-26-1G2G-3R0-25-15-SFF from Planar Monolithic Industries is a Low Noise Amplifier that operates from 1 to 2 GHz. It provides 26 dB of gain with a noise figure of less than 3 dB and has an output P1dB of more than 25 dBm. It requires a DC supply from 12 to 15 V and consumes 400 mA of current. This LNA is available in an epoxy-sealed module that measures 2.5 x 1.0 x 0.33 inches.
Download Datasheet Product Details
Software
Electromagnetic Analysis Tool for Predicting Radar Cross Section
Software  from Remcom

XGtd from Remcom is a Ray-Based EM Simulation Software for assessing the effects of a vehicle or vessel on antenna radiation, predicting coupling between antennas and predicting radar cross section (RCS). It incorporates techniques including Geometric Optics (GO), the Uniform Theory of Diffraction (UTD), Physical Optics (PO), and the Method of Equivalent Currents (MEC).
Download Datasheet Product Details
Termination
2 W Termination from DC to 8 GHz
Termination  from JFW Industries

The 50T-007 from JFW Industries is an RF Termination that operates from DC to 8 GHz. It can handle up to 2 W of average input power and 1 kW of peak power. The termination is matched to 50 ohms and has a VSWR of less than 1.25:1. It is available in a module with N-type (male) connectors.
Download Datasheet Product Details
Termination
1 W RF Terminations from DC to 67 GHz
Termination  from Fairview Microwave

The FMTR11xx Series from Fairview Microwave are RF Terminations that operate from DC to 67 GHz. They can handle input power of up to 1 W and have a VSWR of less than 1.6:1. These terminations are available in modules with 1.85mm, 2.4mm, 3.5mm, SMP and Mini-SMP connectors in male/female configurations.
Download Datasheet Product Details
RF Transistor
1600 W Rugged LDMOS Power Transistor from 1 to 450 MHz
RF Transistor  from Ampleon

The ART1K6PHG from Ampleon is an LDMOS Power Transistor that operates from 1 to 450 MHz. It provides a P1dB of 1600 W with a gain of 27.4 dB and a drain efficiency of 74.7%. The transistor uses Ampleon’s Advanced Rugged Technology (ART) and has been designed to have a wide supply voltage range from 30 V to 55 V.
Download Datasheet Product Details
RF Amplifier
25 W GaN Power Amplifier from 27 to 31 GHz
RF Amplifier  from Nxbeam Inc

The NPA2003-FL from Nxbeam is an RF Power Amplifier that operates from 27 to 31 GHz. It delivers a saturated output power of 25 W (44 dBm) with a small signal gain of 23 dB and has a PAE of 25%. This GaN amplifier consists of three gain stages that can be biased independently providing flexibility to tailor performance to specific application needs.
Download Datasheet Product Details
RF Amplifier
High-Gain Linear Driver Amplifier from 2.3 to 2.7 GHz
RF Amplifier  from Skyworks Solutions

The SKY66051-11 from Skyworks is a High-Gain Linear Driver Amplifier that operates from 2300 to 2700 MHz. This amplifier delivers a linear output power of +19 dBm with a gain of 39 dB. It has an open-loop ACLR of better than -45 dBc for high linearity and a turn-on time of 0.6 µs. This driver amplifier integrates active biasing circuitry to compensate for performance over temperature, voltage, and process variations.
Download Datasheet Product Details
RF Switch
Ultra-CMOS (SOI) SP4T Switch from 1.8 to 5 GHz
RF Switch  from pSemi, A Murata Company

The PE42444 from pSemi is an SP4T RF Switch that operates from 1.8 to 5 GHz. This switch can handle an RMS input power of 10 W (40 dBm), a peak input power of 100 W (50 dBm), and has an insertion loss of 0.5 dB. It uses patented HARP technology enhancements to deliver high linearity of 85 dBm and excellent harmonics performance.
Download Datasheet Product Details
RF Spectrum Analyzer
Handheld RF Spectrum Analyzer from 1 MHz to 2.7 GHz
RF Spectrum Analyzer  from Aim-TTi

The PSA2703 from Aim-TTi is a Handheld RF Spectrum Analyzer that operates from 1 MHz to 2.7 GHz. This analyzer provides RF service engineers with a cost-effective and highly portable tool that can be carried to areas that have traditionally been difficult to access with benchtop instruments. It has a noise level of -105 dBm and can measure amplitude in dBm, dBµV, mV, and µW.
Download Datasheet Product Details
Waveguide to Coax Adapter
Waveguide (R740) to Coaxial (1.35 mm) Adapter from 60 to 90 GHz
Waveguide to Coax Adapter  from Spinner Group

The 533126 from Spinner is a waveguide to the coaxial adapter with an R740 (WG26 | WR12) waveguide interface and a 1.35 mm (Female) coaxial interface that operates from 60 to 90 GHz. This adapter has a return loss of 20 dB and is internally matched to an impedance of 50 ohms. The R 740 (WG26 | WR12) waveguide interface complies with IEC 60153-2 and the 1.35 mm (female) socket complies as per IEEE STD. 287.
Download Datasheet Product Details
Waveguide Isolator
0.2 W Faraday Isolator from 140 to 220 GHz
Waveguide Isolator  from ERAVANT

The STF-05-S1-C from ERAVANT is a Faraday Isolator that operates from 140 to 220 GHz. It can handle a CW input power up to 0.2 W, provides an isolation of 30 dB, and has an insertion loss of 5 dB. This Faraday isolator is constructed with a longitudinal, magnetized ferrite rod that causes a Faraday rotation of the incoming RF signal.
Download Datasheet Product Details
Antenna
Sub-6 GHz LTE/ISM Omnidirectional Whip Antennas
Antenna  from Linx Technologies

The ANT-W63-MON Series from Linx Technologies are Monopole Tilt/Swivel Whip Antennas that are designed to operate in LTE bands from 617 to 3800 MHz and in ISM bands from 2400 to 7125 MHz. These linearly polarized antennas provide a peak gain of 6.1 dBi with an efficiency of 65%. They can handle an input power of up to 5 W and have a VSWR of less than 2.3:1.
Download Datasheet Product Details
About everything RF
everything RF is a product discovery platform for RF & Microwave products/Services. We list over 300,000 Products from more than 1500 Companies across 200 Categories in our database and enable engineers to search for them using our customized parametric search tool.
To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]