Sponsored by Aeroflex / Inmet | |
|
 New RF & Microwave Products this Week |
|
|  | GPS Amplifier from API Technologies The 312 Series of pre-filtered GPS LNA modules are designed to amplify GPS signals while protecting the front end of GPS receivers by filtering out interfaces from an increasingly crowded EM spectrum. The amplifiers have been designed for L1, L1/L2, L5, L1/L5 GPS bands and provide a gain from 16 to 40 dB with a noise figure below 2.5 dB. Download Datasheet | Product Details
|
| | |
|
|  | RF Amplifier from Custom MMIC The CMD197 is a broadband distributed amplifier that operates from 1 to 24 GHz. It provides a gain of 16 dB, a P1dB of 20 dBm and an output IP3 of greater than +30 dBm across its entire bandwidth. The amplifier requires a single positive supply of 8 V and draws 225 mA of current. The CMD197 is available as a die. It is ideal for commercial, military, test and space applications. Download Datasheet | Product Details
|
| | |
|
|  | Signal Generator from Agilent Technologies This series is an alternative to the high-performance and more expensive PSG series of Analyzers from Agilent. The MXG has an output power of 20 dBm at 20 GHz and has a high accuracy, efficiency and near-PSG performance in just two rack units. It has a phase noise of less than -124 dBc/Hz (at 10 GHz, 10 kHz offset) and -75 dBc spurious enables module- and system-level testing up to 40 GHz. Download Datasheet | Product Details
|
| | |
|
|  | PXI Signal Analyzer from Agilent Technologies The M9393A is a PXIe vector signal analyzer (VSA) that provides exceptional accuracy up to 27 GHz – It is available in 8.4 GHz, 14 GHz, 18 GHz and 27 GHz configurations. This PXI module enables engineers to validate the true performance of leading-edge and legacy devices with a 160 MHz analysis bandwidth. It has ±0.15 dB absolute amplitude accuracy, -160 dBm displayed average noise level (DANL), with preamplifier, and 30 dBm third-order intermodulation (TOI). Download Datasheet | Product Details
|
| | |
|
|  | RF Spectrum Analyzer from Signal Hound The BB60A is a high speed spectrum analyzer and a real-time RF recorder. It operates from 9 kHz to 6 GHz and has a 20 MHz real-time bandwidth. It is powered and controlled by a USB 3 interface through which it can stream 140 MB/sec of digitized RF data to your PC, 14-bit samples at 80 million samples per second. It is also an RF recorder. Download Datasheet | Product Details
|
| | |
|
Sponsored by Aeroflex / Inmet |  | If a full hex attenuator better fits your specifications, look no further Aeroflex / Inmet is pleased to introduce a more user friendly version of our most popular 2W SMA attenuator; a full hex (FH) body configuration helps minimize the possibility of the attenuator rotating during installation by providing the technician with increased surface by which to secure the device. The same outstanding performance is now available in the Models 6FH (6GHz) and 18FH (18GHz). Standard attenuation values include 0-10, 12, 15, 20, 30 & 40dB. Similarly, our new FHC model is available for production volume 6GHz applications at slightly reduced electrical performance and lower cost. |
|
|
|
|  | LDMOS Transistor from Freescale The MMRF1306H is a rugged 1.25 kW RF power LDMOS transistor designed for use in high VSWR CW and pulse applications. It operates from 1.8 to 600 MHz and requires a supply from 30 to 50 V. Multiple application circuits are available to demonstrate device performance at different frequencies and signal types. Download Datasheet | Product Details
|
| | |
|
|  | LDMOS Transistor from Freescale The MMRF1305HS is a ruggedized 100 watt RF power LDMOS transistor that operates from 1.8 MHz to 2000 MHz. It requires a supply from 30 to 50 V and is capable of performing into 65:1 VSWRs making it suitable for high load mismatch applications. This transistor is ideal for both narrowband and broadband CW pulse applications such as military/radio communications and radar applications. Download Datasheet | Product Details
|
| | |
|
|  | Balun from Marki Microwave The BAL-0026 is a broadband isolation balun that operates from 300 kHz to 26 GHz. This balanced to unbalanced transformer has a 1:2 impedance ratio (50 Ohm unbalanced, 100 Ohm differential/50 Ohm balanced port). Instrumentation baluns are used to test differential devices with single ended test equipment, but they have long been limited to below 20 GHz in frequency. Download Datasheet | Product Details
|
| | |
|
|  | Balun from Marki Microwave The BAL-0036 is a broadband isolation balun that operates from 300 kHz to 36 GHz. This balanced to unbalanced transformer has a 1:2 impedance ratio (50 Ohm unbalanced, 100 Ohm differential/50 Ohm balanced port). Instrumentation baluns are used to test differential devices with single ended test equipment, but they have long been limited to below 20 GHz in frequency. Download Datasheet | Product Details
|
| | |
|
|  | SP16T Switch from Skyworks The SKY13492 is a SP16T antenna switch that operates from 0.4 to 3.8 GHz with an integrated Mobile Industry Processor Interface (MIPI®) controller. The switch has a low insertion loss and a high isolation making it ideal for UMTS, CDMA2000, EDGE, GSM, and LTE applications. The design features two dedicated GSM transmit ports and three dedicated low-loss TRX ports. The SKY13492 is manufactured in a compact, 2.5 x 3.3 x 0.8 mm, 22-pin surface mount Multi-Chip Module (MCM) package. Download Datasheet | Product Details
|
| | |
|
|  | SP10T Switch from Skyworks The SKY13498 is a SP10T Antenna switch module that operates from 0.4 to 3.8 GHz with an integrated Mobile Industry Processor Interface (MIPI) controller. It maintains a low insertion and high isolation through the band making it ideal for UMTS, CDMA2000, EDGE, GSM, and LTE applications. The design features two dedicated GSM transmit ports and three dedicated low-loss TRX ports. The switch also has an excellent triple beat ratio and 2nd/3rd Order Intermodulation Distortion (IMD2/IMD3) performance. It is available in a compact, 2.5 x 2.5 x 0.8 mm, 20-pin surface mount Multi-Chip Module (MCM) package. Download Datasheet | Product Details
|
| | |
|
|  | SPDT Switch from Triquint The TGS2352-2-SM is a SPDT reflective switch that operates from 0.5 to 12 GHz. This switch is developed using Gallium Nitride (GaN) and can thus handle up to 20 W of power with an insertion loss of less than 1 dB and isolation of over 35 dB through the band. It has a switching speed of 35 ns and control voltage of 0/-40 V. The switch is available in a compact 4 x 4 mm 22 lead QFN package. It is ideal for commercial and military applications. Download Datasheet | Product Details
|
| | |
|
|  | SPDT Switch from MACOM The MASW-010647 is a SPDT Silicon PIN Diode Terminated Switch for the X-Band that operates from 8 to 10.5 GHz. The switch can handle up to 20 W of CW power. The switch has a low insertion loss of 0.8 dB and an isolation of 37 dB. The device integrates a bias network to allow for simplified bias application and switch control. Download Datasheet | Product Details
|
| | |
|
