| New RF and Microwave Products this Week . |
|
|
| Thin-Film RF Chip Attenuators from DC to 8 GHz | |
Fixed Attenuator
from Spectrum Control
|
| The KPA1020S from Spectrum Control are RF Attenuators that operate from DC to 8 GHz. They are available in attenuation values from 1 to 20 dB with an attenuation accuracy of ±2 dB. These 50-ohm thin-film attenuators are designed to reduce the signal power uniformly at different frequencies, temperatures, and power levels. |
| |
Download Datasheet
Product Details | |
|
|
|
| Compact Automated Tuner from DC to 65 GHz for 5G Applications | |
Automated Tuner
from Maury Microwave
|
| The NT-18G-50G-1C Nano5G Automated Impedance Tuner from Maury Microwave has been developed to conduct load pull measurements from 18 to 65 GHz (covering 5G FR2 Frequencies). It's compact size allows the tuner to be mounted directly to the probe tip for on-wafer measurements, thereby ensuring the highest tuning range (VSWR, lowest impedance) at the DUT reference plane. |
| |
Download Datasheet
Product Details | |
|
|
|
| 20 GHz Compact USB Real-Time Spectrum Analyzer | |
RF Spectrum Analyzer
from HAROGIC Technologies
|
| The SAE-200 from HAROGIC Technologies is a Compact USB Real-time Spectrum Analyzer that operates from 9 kHz to 20 GHz. It is based on the superheterodyne architecture and has an analysis bandwidth of 100 MHz with a sweep speed of 1.2 THz/s. This spectrum analyzer provides over 60 dB of image suppression, over 90 dB of IF rejection, and SSB phase noise of -131 dBc/Hz (at 10 MHz offset). It is powered by a USB C port and is compatible with ARM and x86 processors, Linux, and Windows operating systems. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low Noise Amplifier from 22 to 31.5 GHz | |
RF Amplifier
from Teledyne e2v HiRel Electronics
|
| The TDLNA2628SEP from Teledyne e2v Hirel is a Low Noise Amplifier (LNA) that operates from 22 to 31.5 GHz. It provides a small signal gain of 23 dB with a noise figure of 1.6 dB and has a P1dB of 19 dBm. This LNA is fabricated on Teledyne’s 90 nm pHEMT process and has integrated DC blocking caps on both I/O ports for easy handling and simple system integration. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Surface-Mount 1:1 RF Balun from 10 MHz to 9 GHz | |
Balun
from Marki Microwave
|
| The BALHE-0009SMG from Marki Microwave is a 1:1 RF Balun that operates from 10 MHz to 9 GHz. It converts a 50-ohm unbalanced input to a 100-ohm balanced differential output with a phase balance of ±2° and an amplitude balance of ±0.1 dB. This balun provides an isolation of 7 dB and has an insertion loss of 2.5 dB. It can be operated down to 500 kHz to support low-frequency operation. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
| Wireless InSite® 3D Wireless Prediction Software | |
Software
from Remcom
|
| Wireless InSite® from Remcom is a suite of ray-tracing models and high-fidelity EM solvers for the analysis of site-specific radio wave propagation and wireless communication systems. The RF propagation software provides efficient and accurate predictions of EM propagation and communication channel characteristics in complex urban, indoor, rural and mixed path environments. Wireless InSite's unique ray-tracing capabilities determine multipath propagation through a 3D environment, including diffuse scattering at millimeter waves. |
| |
Download Datasheet
Product Details | |
|
|
|
| Portable Direction Finding and Spectrum Monitoring System from 500 MHz to 8 GHz | |
Direction Finding System
from CRFS
|
| The RFeye Array 125 from CRFS is a fully integrated, multi-mission direction-finding system for fixed, vehicle, or transportable applications with simultaneous DF, monitoring, and geolocation capability. It operates from 500 MHz to 8 GHz with 100 MHz of Instantaneous bandwidth. This is a fully integrated plug-and-play system containing a high-performance RFeye Node, spiral antenna modules, and high-speed switch and is available with an optional IP65 radome and mounting kit. |
| |
Download Datasheet
Product Details | |
|
|
|
| 4-Channel Digital Attenuator from 200 to 8000 MHz | |
RF Variable Attenuator
from Vaunix
|
| The LDA-802Q from Vaunix is a bidirectional, 4-Channel Digital Attenuator that operates from 200 to 8000 MHz. It provides an attenuation control range of 120 dB with a step size of 0.1 dB. This step attenuator is powered from a USB port and can be easily programmed for fixed attenuation, swept attenuation ramps and fading profiles directly from the included Graphical User Interface (GUI). |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 125 W Amplifier from 0.7 to 6 GHz for EMC Testing Applications | |
RF Amplifier
from AR RF/Microwave Instrumentation
|
| The 125S1G6 from AR RF/Microwave Instrumentation is a solid-state, Class A, self-contained, air-cooled, broadband amplifier that operates from 0.7 to 6 GHz. It is designed for applications where instantaneous bandwidth, high gain, and linearity are required. This broadband amplifier provides 125 W of output power with a gain of 52 dB when used with a sweep generator. |
| |
Download Datasheet
Product Details | |
|
|
|
| 200 W, Class A/AB Solid-State Power Amplifier from 18 to 26.5 GHz | |
RF Amplifier
from Advanced Amplifiers
|
| The AA-1826G-200 from Advanced Amplifiers is a Solid-State Power Amplifier (SSPA) that operates from 18.0 to 26.5 GHz. It delivers a saturated output power of more than 200 W with more than 53 dB of gain. This SSPA has a Class A/AB linear design, offering high efficiency with excellent reliability and ruggedness. It is ideal for EMI/RFI labs, CW/pulse, and EW communication applications. |
| |
Download Datasheet
Product Details | |
|
|
| Featured Content | | How to Select an Arbitrary Waveform Generator | | An arbitrary waveform generator (AWG) is a signal source that can generate any type of waveform. A basic AWG can include simple functions such as sine waves, triangular waves and square waves. A more advanced AWG can generate direct to RF signals including complex digital modulation schemes such as quadrature amplitude modulation (QAM) and orthogonal frequency modulation (OFDM). Click here to learn more. | | | |
|
|
| Real-Time Peak USB Power Sensors from 50 MHz to 40 GHz | |
RF Power Meter & Sensor
from Boonton
|
| The RTP5000 Series of USB Power Sensors from Boonton are Real-Time peak power sensors that operate from 50 MHz to 40 GHz (available in 6 GHz, 18 GHz and 40 GHz configurations). They have a dynamic range from -60 dBm to +20 dBm with a measurement rate of 100,000 measurements per second, with no gaps in signal acquisition and zero measurement latency. |
| |
Download Datasheet
Product Details | |
|
|
|
| Microwave Signal Generator from 100 KHz to 20 GHz | |
Signal Generator
from AnaPico
|
| The APMQS20 from AnaPico is a Signal Generator with a frequency range from 100 kHz to 20 GHz. This module has been designed to replace the QuickSyn FSW-0020 frequency synthesizer, which was phased out by NI a few years ago. AnaPico’s APMQS20 serves as a drop-in replacement, providing an uncomplicated transition for QuickSyn users and ensuring uninterrupted performance. |
| |
Download Datasheet
Product Details | |
|
|
|
| USB & Ethernet Portable RMS Power Sensor from 50 MHz to 18 GHz | |
RF Power Meter & Sensor
from Mini Circuits
|
| The PWR-18RMS-RC from Mini-Circuits is an RMS Power Sensor that operates from 50 MHz to 18 GHz. It can detect input signals from -60 dBm to +20 dBm and supports the measurement of CW, modulated, pulsed, and multi-tone signals along with wideband digital modulations (including Wi-Fi devices). It has Ethernet (RJ45) and USB Type-C control interfaces with an integrated LCD screen that provides power read-outs. |
| |
Download Datasheet
Product Details | |
|
|
|
| Precision-Calibrated Waveguide Noise Source from 140 to 200 GHz | |
Noise Source
from ERAVANT
|
| The STZ-14420412-05-IT2 from ERAVANT is a Precision-Calibrated Noise Source that operates from 140 to 200 GHz. It has an excess noise ratio (ENR) of 12 dB and an ENR flatness of ±4 dB. This noise source is designed with improved port return loss for high reliability and accurate noise figure measurements. It can work either in CW or pulsed AM mode up to 1 kHz, depending on the driving signal. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 0.6 W Surface-Mount Power Amplifier from 13 to 17.5 GHz | |
RF Amplifier
from Altum RF
|
| The ARF1111Q4 from Altum RF is a Power Amplifier that operates from 13 to 17.5 GHz. It delivers a saturated output power of 0.6 W (~28 dBm) with a gain of 22 dB and a power-added efficiency (PAE) of 40%. This amplifier is pre-matched to 50 ohms and all the RF ports are internally DC-blocked. It is also electrostatic discharge (ESD) protected to simplify handling and assembly operations. |
| |
Download Datasheet
Product Details | |
|
|
|
| 150 W GaN-on-SiC Power Transistor from 3.3 to 3.8 GHz | |
RF Transistor
from Integra Technologies, Inc.
|
| The IGN3338CW150 from Integra Technologies is a GaN-on-SiC RF Power Transistor that operates from 3.3 to 3.8 GHz. It delivers a CW output power of more than 150 W with a gain of 10 dB and an efficiency of 47%. This transistor requires a DC supply of 28 V and consumes 80 mA of current. It is ideal for S-band system applications. |
| |
Download Datasheet
Product Details | |
|
|
|
| 5G Embedded IoT Antenna from 600 to 6000 MHz | |
Antenna
from Quectel
|
| The YC0018CA from Quectel is a 5G Embedded IoT Antenna that operates from 600–960 MHz, 1427–1707 MHz, 1710–2170 MHz, 2300–2700 MHz, 3300–5000 MHz and 5100–6000 MHz. It can be used with other 5G antennas for MIMO (multiple input, multiple output) applications in which multiple antennas are used at both the source (transmitter) and the destination (receiver). |
| |
Download Datasheet
Product Details | |
|
|
|
| 2.4/5/6 GHz Wi-Fi 7 SoC | |
Wireless SoC
from MaxLinear, Inc
|
| The MxL31712 from MaxLinear is a?2.4, 5, and 6 GHz Wi-Fi 7 SoC. It is based on the IEEE 802.11be standard and has 12 spatial streams delivering an Extremely High Throughput (EHT) of 18.6 Gbps. This SoC has a bandwidth of 320 MHz and supports an enhanced modulation scheme of up to 4096 QAM. |
| |
Download Datasheet
Product Details | |
|
|
|
| Flexible On-Metal UHF RFID Tag for FCC Applications | |
RFID Tag
from Identiv
|
| The LA1PADUE0307 from Identiv is a Flexible On-Metal UHF RFID Tag designed for container tracking, metallic commodities and goods, bicycle tracking, and the automotive industry. It is based on the NXP UCODE8 IC with an EPC memory of 128 bits. The tag is extremely thin with a total thickness of ~1 mm and an antenna thickness of 120 µm and has a read range of up to 11 m. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Washable UHF RFID Garment Tag with a 6-meter Range | |
RFID Tag
from ID Tech Solutions Pvt. Ltd.
|
| The IDT.RF.T.TEX.BL from ID Tech Solutions is a UHF Passive RFID Tag that operates from 865 to 868 MHz and 902 to 928 MHz. It is based on the Alien Higgs-3/4, Monza 4/4QT/5/R6/R6P, or UCODE 7/8 RFID chip and has a read range from 3 to 6 meters (depending on the chip used). This Gen2 RFID tag is resistant to chemical solvents and moisture and is designed to sustain up to 100 washes and lofty temperatures. |
| |
Download Datasheet
Product Details | |
|
|
|
| N-Type to SMA Flexible Cable Assemblies | |
RF Cable Assembly
from Amphenol RF
|
| The 095-909-195 Series from Amphenol RF are N-Type to SMA Flexible Cable Assemblies that operate up to 11 GHz. These between-series cable assemblies provide a versatile solution for applications such as connecting to antennas within a device, Radars, satellite systems, and broadcast equipment. They use an RG-142 cable which offers a low loss solution with a bend radius of 1 inch. |
| |
Download Datasheet
Product Details | |
|
