| Featured Products this Week . |
|
|
| USB Based Tracking Generator from 100 kHz to 12.4 GHz | |
Signal Generator
from Signal Hound
|
| The USB-TG124A from Signal Hound is a USB-based tracking generator that operates from 100 kHz to 12.4 GHz. It works with the USB-SA124A spectrum analyzers to measure filters, attenuators, amplifiers and other components to carry out scalar network analyzer measurements. It is compact, simple to use, and an effective troubleshooting and analysis tool in the lab or in the field. It can be used by amateur radio enthusiasts and microwave communication professionals to provide fast, accurate results. |
| |
Download Datasheet
Product Details | |
|
|
|
| 4-Port USB Vector Network Analyzer, 100 kHz to 9 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The C1409 from Copper Mountain Technologies is a 4-port modular vector network analyzer that operates from 100 kHz to 9 GHz. The VNA can measure all S parameters and can be controlled using any Windows PC or laptop. It has a dynamic range of up to 138 dB (10Hz IF BW), directivity of 46 dB and sweep speeds of 10 microseconds per point. |
| |
Download Datasheet
Product Details | |
|
|
|
| 16x16 Butler Matrix from 0.7 to 6 GHz for 5G MIMO RF Testing | |
Butler Matrix
from Spectrum Control
|
| The 8401-16-5 from Spectrum Control is a 16x16 Butler Matrix that operates from 0.7 to 6 GHz. It can handle an input power of 37 dBm, provides more than 10 dB of isolation, and has an insertion loss of less than 24 dB. This butler matrix transfers the signal reciprocally from any of the 16 input ports to any of the 16 output ports with a phase accuracy of ±20°. |
| |
Download Datasheet
Product Details | |
|
|
|
| RF Diagnostic Test Chamber from 400 MHz to 18 GHz | |
Antenna Measurement System
from Rohde & Schwarz
|
| The R&S DST200 from Rohde & Schwarz is an RF Diagnostic Test Chamber for a frequency range from 400 MHz to 18 GHz. It has been designed for accurate RF testing and analysis during development. This compact chamber supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used during the product design and optimization phase. |
| |
Download Datasheet
Product Details | |
|
|
|
| 18 GHz SMA Straight Cable Plug (Male) Connector | |
RF Connector
from HUBER+SUHNER
|
| The 11_SMA-50-2-116/111_N from HUBER+SUHNER is an 18 GHz SMA Straight Cable Plug (male) connector. It uses Copper Beryllium alloy for center contact, outer conductor, and body and employs a PTFE insulator. This 50-ohm connector meets the IEC 60169-15, MIL-STD-348A/310 and CECC 22110 standards and can be fitted with GX-02272, RG-174/U and RG-316/U cables. |
| |
Download Datasheet
Product Details | |
|
|
|
| 125 W GaN Power Transistor from 1 to 2700 MHz | |
RF Transistor
from NXP Semiconductors
|
| The MMRF5018HS from NXP Semiconductors is a Power Transistor that operates from 1 to 2700 MHz. It provides an output power of up to 125 W with a power gain of 17.3 dB and a drain efficiency of 40%. This transistor is developed using advanced GaN-on-SiC technology and includes input-matching circuitry for extended bandwidth performance. |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by DesignCon 2024 | | |
|
|
| Dual-Polarized 2-Beam, 4-Element Beamformer IC from 17.7 to 21.2 GHz | |
Beamforming IC
from Analog Devices
|
| The ADAR3002 from Analog Devices is a Beamformer IC that operates from 17.7 to 21.2 GHz. This dual-polarized, dual-beam, 4-element dual-polarized beamforming IC is designed for phased array antennas. In each of the 16 RF channels, it provides an adjustable gain of 31 dB (in 0.5 dB steps) and a phase adjustment of 360° (in 5.625° steps) via Variable Amplitude and Phase (VAP) blocks. |
| |
Download Datasheet
Product Details | |
|
|
|
| 5 GHz FBAR Integrated Front End Module for Wi-Fi 7 Applications | |
Front End Module
from Broadcom
|
| The AFEM-W750 from Broadcom is a 5 GHz Wi-Fi 7 FBAR Integrated Front End Module (FiFEM). The FEM consists of a power amplifier (PA), a high-gain low-noise amplifier (LNA), a transmit/receive (T/R) switch, and a 5 GHz FBAR Band-Pass filter (UNII-1 to UNII-3) for coexistence with 6 GHz Wi-Fi. It provides an output power of +25 dBm and a 6 GHz coexistence rejection of 50 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| SP65T Absorptive PIN Diode Switch from 0.1 to 4 GHz | |
RF Switch
from American Microwave Corporation
|
| The MSN-65DT-051-DEC-MP from American Microwave Corporation is an SP65T Absorptive PIN Diode Switch that operates from 100 MHz to 4 GHz. It has an ON/OFF switching time of less than 150 ns, a rise/fall time of 50 ns, and provides isolation of more than 45 dB. This switch can handle a CW input power of up to +20 dBm and has an insertion loss of less than 15 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| 1 W, 6-Channel Switched Filter Bank from 30 to 600 MHz | |
Switched Filter Bank
from Quantic PMI (Planar Monolithics)
|
| The 6SFB-30M600M-CD-SFF from Quantic PMI is a 6-Channel Switched Filter Bank that operates from 30 to 600 MHz. It has a switching speed of 500 ns and provides more than 40 dB of isolation. This filter bank can handle an input power of up to 1 W and has an insertion loss of 4 dB. It requires a DC supply of +15 V or -15 V and consumes less than 300 mA of current. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 6 dB Directional Coupler from 0.8 to 2.2 GHz | |
Directional Coupler
from MECA
|
| The 715-06-1.500 from MECA is a Directional Coupler that operates from 0.8 to 2.2 GHz. This 6 dB coupler provides a directivity of more than 22 dB and has an insertion loss of 0.1 dB. It can handle a forward input power of 100 W, a reverse power of 10 W reverse, and has a VSWR of less than 1.20:1. This coupler is available in a RoHS-compliant Aluminum housing that measures 4.46 x 1.50 x 0.86 inches with N-type (female) connectors. |
| |
Download Datasheet
Product Details | |
|
|
|
| 9-Way Divider/Combiner from 20 to 3000 MHz | |
Power Divider
from Preferred Power Products (P3)
|
| The PNW9-20-3000-1S from Preferred Power Products is a 9-Way Divider/Combiner that operates from 20 to 3000 MHz. It can handle an input power of up to 1 W (as a divider), provides up to 23 dB of isolation, and has an insertion loss of less than 16 dB. This divider/combiner has a phase balance of ±4° and an amplitude balance of ±0.75 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2400 W GaN Pulsed Power Amplifier from 5.4 to 5.9 GHz | |
RF Amplifier
from RFHIC
|
| The RRP54592K4-24 from RFHIC is a Pulsed Power Amplifier that operates from 5.4 to 5.9 GHz. It provides a pulsed output power of 2400 W with a gain of 23.8 dB (±0.5 dB) and has an efficiency of up to 30%. The amplifier has a duty cycle of 10%, a pulse width of 100 µs and a switching time of 0.1 µs. It has an amplitude pulse droop of 0.5 dB, phase deviation of ±20° and a rise/fall time of less than 50 ns. |
| |
Download Datasheet
Product Details | |
|
|
|
| 150 W Rack-Mounted Solid-State Power Amplifier from 0.5 to 6 GHz | |
RF Amplifier
from Exodus Advanced Communications
|
| The AMP2099C from Exodus Advanced Communications is a Solid-State Power Amplifier that operates from 0.5 to 6 GHz. It delivers a saturated output power of more than 150 W (CW/Pulsed) with a gain of over 53 dB. This class A/AB amplifier uses high-power advanced technology devices and has built-in protection circuits (up to 10 dBm) with extensive monitoring such as forward/reflected power monitoring, VSWR, voltage/current/temperature sensing. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Ethernet-Controlled Programmable Rotary Attenuators from 6.5 to 500 GHz | |
Waveguide Attenuator
from Flann Microwave
|
| The 625-03 Series from Flann Microwave are Ethernet-Controlled Precision Programmable Attenuators that operate from 6.5 to 500 GHz. They have an attenuation range from 0 to 60 dB, can handle up to 6 W of power and have an insertion loss of less than 5 dB. These attenuators utilize the proven rotary vane principle and Flann’s industry-standard experience to offer a very high performance. |
| |
Download Datasheet
Product Details | |
|
|
|
| 0.5 W Driver Amplifier from 2.3 to 5 GHz | |
RF Amplifier
from Qorvo
|
| The QPA9122 from Qorvo is a Driver Amplifier that operates from 2.3 to 5 GHz. It delivers an output power of 0.5 W (P3dB) with a gain of 36 dB. This amplifier is internally matched to 50 ohms over the entire operating frequency range and incorporates a shut-down function through the VPD pin. It requires a DC supply of 5 V and consumes 95 mA of current. |
| |
Download Datasheet
Product Details | |
|
|
|
| Testing Chamber for Military Components from 9 kHz to 40 GHz | |
Anechoic Chamber
from FRANKONIA
|
| The MIL CHC from FRANKONIA is a Compact Hybrid Chamber that can be used to test components that operate from 9 kHz/26 MHz to 40 GHz. It is designed for military components testing according to MIL-STD 461 and DO-160 standards and has been adapted for radiated emission and immunity tests at a 1.0 m measuring distance. This chamber uses advanced, long-lasting Frankosorb® absorber lining with nano thin-film technology for long-term stability (Ferrite F006, H450, or H600 option). |
| |
Download Datasheet
Product Details | |
|
|
|
| Sub-Millimeter-Wave Low-Noise Gain Block from 220 to 325 GHz | |
RF Amplifier
from Northrop Grumman
|
| The MGA2101 from Northrop Grumman is a Low-Noise Gain Block that operates from 220 to 325 GHz. It provides a linear gain of 13 dB with a noise figure of 5 dB and delivers an output power of 1 mW. This unconditionally stable gain block requires a bias voltage of 1.75 V and consumes 24 mA of current. It is available in a module that measures 1.00 x 0.75 x 1.00 inches and has standard WR3.4 waveguide interfaces. |
| |
Download Datasheet
Product Details | |
|
|
|
| 75 kW Fixed Frequency Magnetron Tube from 896 to 929 MHz | |
Magnetron
from Microwave Techniques LLC
|
| The L10016-5 from Microwave Techniques is a Fixed Frequency Magnetron Tube that operates in the L-Band from 896 to 929 MHz. This magnetron tube is capable of delivering a continuous CW output power of 75 kW with an efficiency of 88%. It has a water-cooled anode with an anode voltage from 17 to 18 kV and an anode current of 5 A. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 10 Gbps Point-to-Point FDD Microwave Link 71 to 86 GHz | |
Microwave Backhaul Radio Links
from RACOM
|
| The RAy3-80 from RACOM is a Point-to-Point (PtP) Microwave Link that operates in the E-band from 71 to 86 GHz. It supports channel bandwidths of up to 2000 MHz and delivers a data rate of up to 10 Gbps (in each direction). This microwave link supports FDD duplex traffic with flexible duplex spacing and 2PSK, 4PSK, 8PSK, 16QAM, 32QAM, 64QAM, and 128QAM modulation schemes. |
| |
Download Datasheet
Product Details | |
|
