| Featured Products this Week . |
|
|
| Low Profile Wirewound Chip Inductors from 0.6 to 22 nH | |
RF Inductor
from Coilcraft
|
| The 0201CT Series from Coilcraft are Low Profile Wirewound Chip Inductors with inductance values from 0.60 to 22 nH. They have higher Q and lower DCR than similarly sized thin-film types and are optimized for high-frequency impedance matching in applications such as cell phones, wearable devices, Wi-Fi, Bluetooth, GPS, and LTE/5G IoT networks. |
| |
Download Datasheet
Product Details | |
|
|
|
| 18 GHz Right-Angle SMA Jack (Female) PCB Connector | |
RF Connector
from HUBER+SUHNER
|
| The 85_SMA-50-0-103/111_N from HUBER+SUHNER is an 18 GHz Right-Angle SMA Jack (female) PCB Connector. It employs a PTFE insulator and uses Copper Beryllium alloy for center contact, outer conductors and body. This 50-ohm connector meets the IEC 60169-15, MIL-STD-348A/310 and CECC 22110 standards. It can withstand 500 mating cycles and has an operating temperature range of -65°C to +165°C. |
| |
Download Datasheet
Product Details | |
|
|
|
| USB Based Tracking Generator from 100 kHz to 12.4 GHz | |
Signal Generator
from Signal Hound
|
| The USB-TG124A from Signal Hound is a USB-based tracking generator that operates from 100 kHz to 12.4 GHz. It works with the USB-SA124A spectrum analyzers to measure filters, attenuators, amplifiers and other components to carry out scalar network analyzer measurements. It is compact, simple to use, and an effective troubleshooting and analysis tool in the lab or in the field. |
| |
Download Datasheet
Product Details | |
|
|
|
| 100 W Class A/AB Solid-State Power Amplifier from 6 to 12 GHz | |
RF Amplifier
from Exodus Advanced Communications
|
| The AMP2053B-1 from Exodus Advanced Communication is a Solid-State Power Amplifier that operates from 6 to 12 GHz. It delivers a CW/Pulsed output power of 100 W with a power gain of more than 50 dB. This class A/AB linear amplifier provides high efficiency with excellent reliability and ruggedness. It has 2-tone intermodulation (IMD) of -30 dBc, spurious emissions of -60 dBc, and harmonics of less than -20 dBc. |
| |
Download Datasheet
Product Details | |
|
|
|
| 100 W, Uni-Directional Fixed Attenuators from DC to 8.4 GHz | |
Fixed Attenuator
from JFW Industries
|
| The 50HFFE-XXX-100/8 Series from JFW Industries are Uni-directional Fixed Attenuators that operate from DC to 8.4 GHz. They are available in attenuation values of 6, 10, 20, 30, and 40 dB with an attenuation accuracy of ±1.3 dB. These attenuators can handle a Uni-directional RF input power of 100 W, a reverse power of 20 W, and a peak power of 1 kW (5 microsecond pulse, 1% duty cycle). |
| |
Download Datasheet
Product Details | |
|
|
|
| 4-Way, In-Phase Power Divider from 2 to 4 GHz for Military Applications | |
Power Divider
from MECA
|
| The P4S-3.100 from MECA is a 4-way Power Divider/Combiner that operates from 2 to 4 GHz. It can handle an input power of up to 20 W, provides 25 dB of isolation and has an insertion loss of less than 1 dB. This in-phase power divider has an amplitude balance of ±0.8 dB and a phase balance of ±7°. It is available in an aluminium module that measures 2 x 2 x 0.75 inches with SMA (female) connectors. |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by MWC Barcelona | | |
|
|
| Bench-Top RF Shield Box from 20 MHz to 12 GHz | |
RF Shielded Test Enclosure
from RF Electronics
|
| The HDRF-1970-C from RF Electronics is an RF Shield Box for the frequency range from 20 MHz to 12 GHz. It has a thick RF-absorbing foam that deadens standing waves and reflections to provide more than 130 dB of isolation (at 20 MHz – 1 GHz). The test box has shielded power filters for powering devices placed inside the box while blocking all wireless signals. |
| |
Download Datasheet
Product Details | |
|
|
|
| 8x8 Butler Matrix from 0.7 to 6 GHz | |
Butler Matrix
from Spectrum Control
|
| The 8401-8-5 from Spectrum Control is an 8x8 Butler Matrix that operates from 0.7 to 6 GHz. It can handle an input power of 5 W (~37 dBm), has an insertion loss of less than 16 dB, and provides a port-to-port isolation of 20 dB. This butler matrix is designed to transfer a signal reciprocally from any of the eight input ports to any of the eight output ports with an output phase accuracy of ±20° (at 5 GHz). |
| |
Download Datasheet
Product Details | |
|
|
|
| 2-Port Compact USB VNA from 300 kHz to 1.3 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The TR1300/1 from Copper Mountain Technologies is a 2-Port lab-grade vector network analyzer that operates from 300 kHz to 1.3 GHz. This compact computer controlled VNA has a dynamic range of 130 dB and can measure up to 100,001 measurement points. It includes an RF measurement module and TR software application which runs on Windows or Linux operating system on a PC, laptop, tablet, or x86 board computer connecting to the measurement hardware via USB interface. |
| |
Download Datasheet
Product Details | |
|
|
|
| 500 W IFF Transponder for SWaP-C Constrained Military Applications | |
Radar Transponder
from BAE Systems
|
| The AN/DPX-7 from BAE Systems is an Identification Friend or Foe (IFF) Transponder that is designed to identify and track aircraft, ships, and other ground forces. It incorporates an ADS-B passive-receive capability to support situational awareness and sense-and-avoid applications. This transponder provides Mode 5, Mode S, and ADS-B functionality in a reduced-size unit at a lower cost than current military transponders, making it suitable for size, weight, and power (SWaP) constraint applications. |
| |
Download Datasheet
Product Details | |
|
|
|
| USB-Powered Real-Time Peak Power Sensor from 50 MHz to 40 GHz | |
RF Power Meter & Sensor
from Boonton
|
| The RTP5006 from Boonton is a Real-Time Peak Power Sensor that operates from 50 MHz to 40 GHz. It has a dynamic range from -60 dBm to +20 dBm and a pulse width of more than 10 ns. This power sensor offers excellent performance with wide video bandwidth, fast rise times, fine time resolution, narrow minimum pulse widths, and good measurement reading rates. |
| |
Download Datasheet
Product Details | |
|
|
|
| 10 MHz to 6 GHz (Optional to 24 GHz) Real-Time Phase Noise Analyzer | |
Phase Noise Analyzer
from Holzworth Instrumentation
|
| The HA7062C from Holzworth is a real time fully integrated phase noise analysis system that operates from 10 MHz to 6 GHz. It utilizes the same core engine from the HA7402C analyzer along with a pair of high performance RF Synthesizers as the test signal LOs. The stability of the agile synthesizers operating as LO sources for the high speed, cross-correlation core enables an extremely reliable phase noise analyzer. |
| |
Download Datasheet
Product Details | |
|
|
|
| 20 GHz Compact USB Real-Time Spectrum Analyzer | |
RF Spectrum Analyzer
from HAROGIC Technologies
|
| The SAE-200 from HAROGIC Technologies is a Compact USB Real-time Spectrum Analyzer that operates from 9 kHz to 20 GHz. It is based on the superheterodyne architecture and has an analysis bandwidth of 100 MHz with a sweep speed of 1.2 THz/s. This spectrum analyzer provides over 60 dB of image suppression, over 90 dB of IF rejection, and SSB phase noise of -131 dBc/Hz (at 10 MHz offset). |
| |
Download Datasheet
Product Details | |
|
|
|
| Wideband Multi-Channel Satellite Link Simulator | |
Satellite Link Emulator
from Square Peg Communications Inc
|
| The RLS-2100 from Square Peg Communications is a comprehensive satellite channel simulator with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full-motion support and integrated GPS simulators. It can provide end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. |
| |
Download Datasheet
Product Details | |
|
|
|
| Bandpass Filter with Passband from 8.2 to 10.34 GHz | |
Band Pass Filter
from American Microwave Corporation
|
| The SM-8T-818 OPTION A8429468-1 from American Microwave is a Bandpass Filter with a passband from 8.2 to 10.34 GHz. It can handle an input power of 200 mW, has a passband insertion loss of less than 2.0 dB and a VSWR of better than 1.5:1. This filter is available in a module that measures 4.00 x 1.50 x 0.75 inches with SMA-female input connector and SMA-male output connector. |
| |
Product Details | |
|
|
|
| 60 W Space-Qualified TWT Power Amplifiers from 10.75 to 21.2 GHz | |
RF Amplifier
from Stellant Systems
|
| The nanoMPM® from Stellant Systems are Power Amplifiers that operate from 10.75 to 12.75 and 17.3 to 21.2 GHz. They deliver a saturated output power of 60 W, and a linear output power of 30 W and have an efficiency of 35%. These amplifiers leverage the best of solid-state and TWT vacuum technology and utilize a high-gain pre-distortion solid-state linearizer, four wideband high-power mini-TWTs, and a proprietary compact nanoMPM® EPC. |
| |
Download Datasheet
Product Details | |
|
|
|
| Rugged Low Noise Amplifier from 18 to 40 GHz | |
RF Amplifier
from AmpliTech
|
| The APT5-18004000-3005-D40 from AmpliTech is a Low Noise Amplifier (LNA) that operates from 18 to 40 GHz. It provides a gain of more than 45 dB with a noise figure of less than 3 dB and has a P1dB of 5 dBm. This LNA is based on pHEMT technology and complies with MIL-883 and MIL-45208 construction and reliability specifications. |
| |
Download Datasheet
Product Details | |
|
|
|
| Benchtop Power Amplifier from 6 to 18 GHz for EMC Applications | |
RF Amplifier
from RF-Lambda
|
| The REMC06G18GG from RF-Lambda is a solid state power amplifier that operates from 6 to 18 GHz. It provides a saturated output power of 55 dBm with a gain of 77 dB and has an attenuation range of 31.5 dB with 0.5 dB steps. The amplifier is available as a benchtop module with N-type female connectors and is ideal for Military & Defense, Wireless Infrastructure, and Test and Measurement applications. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 3.5 W GaN Power Amplifier MMIC from 47 to 52 GHz | |
RF Amplifier
from Nxbeam Inc
|
| The NPA4010-DE from Nxbeam is a Power Amplifier MMIC that operates in the V-band from 47 to 52 GHz. It delivers a saturated output power of 3.5 W with a linear gain of 24 dB and a PAE of 23%. This amplifier has been developed on a 0.15um GaN HEMT on SiC process and has an RF input and output match to 50 Ohms with DC blocking capacitors for easy system integration and fully passivated for reliable operation. |
| |
Download Datasheet
Product Details | |
|
|
|
| 28 dBm Power Amplifier from 18 to 40 GHz | |
RF Amplifier
from Talent Microwave Inc
|
| The TLPA18G40G-38-27 from Talent Microwave is a Power Amplifier that operates from 18 to 40 GHz. It delivers a saturated output power of 28 dBm (~0.63 W) with a gain of 43 dB and a gain flatness of ±2.5 dB. This amplifier requires a DC supply of 12 V and consumes less than 1.2 A of current. It is available as a module that measures 60 x 50 x 12 mm with 2.92 mm (female) connectors. |
| |
Download Datasheet
Product Details | |
|
|
|
| GaN-Based Waveguide Low Noise Amplifier from 90 to 96 GHz | |
RF Amplifier
from AT Microwave
|
| The AT-LNA-9096-1605GNT from AT Microwave is a GaN Low Noise Amplifier that operates from 90 to 96 GHz. It delivers a gain of 15 dB with a noise figure of less than 6 dB and a saturated output power of 18 dBm. This LNA requires a DC supply from 8 to 12 V and consumes 60 mA of current. It can be used both as a general driver and a low noise amplifier (LNA). |
| |
Download Datasheet
Product Details | |
|
|
|
| High Performance, Cost-effective, Easy-to-use GNSS Simulator | |
GNSS Simulator
from Safran Electronics & Defense
|
| The GSG-7 from Safran is a GNSS Simulator with advanced simulation capabilities available in a compact form factor at a competitive price. It features an internal RF combiner and provides high-end performance with a 1000 Hz simulation iteration rate, high dynamics, real-time synchronization, Hardware-in-the-Loop (HIL) integration, and simulation of all-in-view satellite signals. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
|
