| Featured Products this Week . |
|
|
| 2-Port Vector Network Analyzer from 9 kHz to 4.5 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The S5045 from Copper Mountain Technologies is a 2-Port Vector Network Analyzer that operates from 9 kHz to 4.5 GHz. It has a dynamic range of 130 dB (10 Hz IF BW) and can be used to measure all four S parameters (S11, S21, S12, and S22). The output power of this VNA can be adjusted from -55 dBm to 5 dBm and has a measurement speed of 70 µs. |
| |
Download Datasheet
Product Details | |
|
|
|
| 100 W CW/Pulsed Solid-State Power Amplifier from 6 to 18 GHz | |
RF Amplifier
from Exodus Advanced Communications
|
| The AMP2033-LC from Exodus Advanced Communications is a Solid-State Power Amplifier that operates from 6 to 18 GHz. It delivers a CW/Pulsed saturated output power of more than 100 W with a power gain of over 50 dB. The amplifier has built-in protection circuits with optional monitoring parameters for forwarding/Reflected power, VSWR, voltage, current & temperature sensing for superb reliability and ruggedness. |
| |
Download Datasheet
Product Details | |
|
|
|
| Surface-Mount Ferrite Transformers from 150 kHz to 1200 MHz | |
Balun
from Coilcraft
|
| The WBC Series from CoilCraft are Wideband Transformers with bandwidths from 150 kHz to 1200 MHz. They have an impedance ratio of up to 1:16 and an insertion loss of less than 2 dB. The transformers have a ferrite core and are available in tapped or untapped configurations. They can handle an input power of 0.25 W and have a current rating of up to 250 mA. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Bandpass Filter MMIC with Passband from 17.52 to 21.45 GHz | |
Band Pass Filter
from AmpliTech
|
| The AGM-011 from AmpliTech is a GaAs Bandpass Filter MMIC with a passband from 17.52 to 21.45 GHz. It has a passband insertion loss of less than 3.8 dB and provides a rejection of 30 dB at 12.58 and 27.77 GHz. The filter is available in a package that measures 1.00 x 0.75 x 0.10 mm and is suitable for use in communication systems, point-to-point radios, fiber optics, test equipment, and military & space applications. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
| Sponsored by MWC Barcelona | | |
|
|
| Waveguide VNA Calibration Kits from 2.6 to 50 GHz | |
VNA Calibration Kit
from Maury Microwave
|
| The Waveguide VNA Calibration Kits from Maury Microwave can be used at frequencies up to 50 GHz. Calibration of VNAs are extremely important to accurately determine one-port and two-port network characteristics of RF and microwave devices. Maury Microwave has developed a comprehensive line of waveguide VNA calibration kits that are available with WR284, WR229, WR 187, WR159, WR137, WR112, WR90, WR75, WR62, WR51, WR42, WR34, WR28, and WR22 waveguides. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2.4 GHz Bluetooth 5.2 Module for Industrial and Building Automation | |
RF Module
from Silicon Labs
|
| The BGM220P from Silicon Labs is a 2.4 GHz Wireless Gecko Bluetooth Module that is designed and built to meet the performance, security, and reliability requirements of battery-powered IoT products. It supports Bluetooth 5.2 (BLE), direction-finding, and Bluetooth mesh low power node protocols. Based on the EFR32BG22 SoC, the BGM220P enables Bluetooth Low Energy connectivity while delivering best-in-class RF range and performance with OTA firmware updates, enhanced security features, and low energy consumption. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 5G Wireless Module for Home, Enterprise, and Manufacturing Applications | |
Cellular Module
from Fibocom
|
| The FG190W-NA from Fibocom is a 5G Wireless Module that is compliant with the 3GPP Release 17 standard. It delivers a downlink data rate of up to 6.18 Gbps and an uplink data rate of up to 900 Mbps. This module supports global 5G Sub-6, LTE FDD/TDD, UMTS & CDMA bands, and has 4 antennas. It requires a DC supply of 3.8 V and can be controlled via USB 3.1/3.0/2.0, PCIe 4.0/3.0, UIM, and I2S interfaces. |
| |
Download Datasheet
Product Details | |
|
|
|
| 60 GHz High-Resolution SiGe BiCMOS FMCW Radar Sensor | |
Radar Sensor
from Infineon Technologies
|
| The BGT60UTR11AIP from Infineon Technologies is a 60 GHz Radar Sensor with a bandwidth of 5.6 GHz. This Antenna-in-Package (AIP) radar sensor with ±60° Field of View (FoV) has an analog-to-digital converter (ADC) with a sampling rate of 4 Mbps. It is based on Infineon's B11 SiGe BiCMOS technology and has a ramp speed of up to 400 MHz/µs that allows FMCW operations with extremely high resolution. |
| |
Download Datasheet
Product Details | |
|
|
|
| 4-Channel Analog 5G Beamforming IC from 24.25 to 27.5 GHz | |
Beamforming IC
from NXP Semiconductors
|
| The MMW9004KC from NXP is a 4-channel Analog Beamforming IC that operates in the 5G frequency bands from 24.25 to 27.5 GHz. Each channel of this IC consists of a Tx chain and an Rx chain. Both Tx and Rx chains include a phase shifter and a variable gain amplifier (VGA). They provide a Tx gain of 30 dB, an Rx gain of 24 dB, and a high phase and amplitude resolution. |
| |
Download Datasheet
Product Details | |
|
|
|
| Ganged, Multi-Position SMPM Cable Assembly from DC to 50 GHz | |
RF Cable Assembly
from Samtec
|
| The Magnum RFTM GC47 from Samtec is a Ganged, Multi-Position SMPM Cable Assembly that operates from DC to 50 GHz. It has 0.047-inch low-loss, flexible cables with a minimum bend radius of 5.0 mm, a dielectric withstanding voltage of more than 325 V (RMS), and a VSWR of less than 2:1. This cable assembly has a space-saving, high-density design with a push-on interface that enables quick installation. |
| |
Download Datasheet
Product Details | |
|
|
|
| Automotive-Grade mmWave Radar SoC from 76 to 81 GHz | |
Automotive Radar Chipset
from Calterah Semiconductor Technology
|
| The CAL77S322-AE from Calterah Semiconductor Technology is a Millimeter-Wave Radar SoC that operates from 76 to 81 GHz. It has 2 transmit and 2 receive channels with an integrated phase shifter and power saturation detector. This SoC has a high-speed ADC that delivers a sampling rate of up to 25 MS/s and also supports the down-sampling function. |
| |
Download Datasheet
Product Details | |
|
|
|
| Ka-Band Block Up-Converter with Integrated Linearizer | |
Block Up Converter
from Teledyne Microwave Solutions
|
| This is a Ka-Band Block Up-Converter (BUC) with an integrated IF Linearizer up-converts an IF Band signal from 1-2 GHz to 29-30 GHz or 30-31 GHz. The output band is selected via an RS-422 command, as is gain control, mute, and reference frequency selection. The RS-422 interface also allows reporting of the input power to the mixer, internal temperature, and local oscillator (LO) lock detect. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 1 W Bias Tee from 10 MHz to 6 GHz | |
Bias Tee
from Benchmark Lark Technology
|
| The BT Series from Lark Engineering are Bias Tees that operate from 10 MHz to 6 GHz. They can handle an RF power of up to 1 watt and an input current of up to 600 mA while operating over a supply of 5 - 28 V. They are available in connectorized or surface mount modules. |
| |
Download Datasheet
Product Details | |
|
|
|
| 31 dB, 6-Bit Digital Attenuator MMIC from 0.1 to 8 GHz | |
RF Variable Attenuator
from Sainty-Tech Communications Limited
|
| The BW179D from Sainty-Tech Communications is a 6-Bit GaAs Digital Attenuator MMIC that operates from 0.1 to 8 GHz. It provides an attenuation from 0.5 to 31.5 dB with an accuracy of 0.5 dB (RMS) and has a switching time of 30 ns. This attenuator can handle an input power of +24 dBm and has an insertion loss of 2.5 dB. It is available as a bare die that measures 2.40 x 1.40 x 0.10 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Multi-Constellation Triple-band + L-band GNSS Antenna | |
GPS/GNSS Antenna
from Tallysman Wireless
|
| The ARM972XF from Tallysman is a Triple-band + L-band GNSS Antenna. It uses Tallysman’s patented Accutenna® technology to cover GPS/QZSS-L1/L2/L5, GLONASS-G1/G2/G3, Galileo-E1/E5a/E5b, BeiDou-B1/B2a/B2b, NavIC-L5 + L-band correction services. This antenna has an integrated low-noise amplifier (LNA) that operates from 1160 to 1606 MHz and provides out-of-band rejection of more than 45 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| 10-Port Multi-Band Stadium Sector Antenna from 694 to 3800 MHz | |
Base Station Antenna
from CommScope
|
| The RVVSS-50M-F from CommScope is a 10-Port Multi-Band Sector Antenna that operates from 694-960 MHz, 1695-2690 MHz, and 3300-3800 MHz. This ±45° polarized antenna provides a gain of 12.1 dBi and has a VSWR of 1.5:1. It has a horizontal and vertical beamwidth of 57° with rectangular patterns and sharp cut-off for covering a section of the crowd in stadiums. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low Noise Amplifier from 1 to 20 GHz | |
RF Amplifier
from Quantic PMI (Planar Monolithics)
|
| The PE2-35-120-5R0-10-12-SFF from Quantic PMI (Planar Monolithics) is a Low Noise Amplifier that operates from 1 to 20 GHz. It provides more than 30 dB of gain with a noise figure of 3 dB and has an output P1dB of over +10 dBm. This amplifier requires a DC supply from +12 to +15 V and consumes 300 mA of current. It is unconditionally stable and features internal voltage regulation with options for temperature compensation and gain/phase matching. |
| |
Download Datasheet
Product Details | |
|
|
|
| Reflectionless Bandpass Filter MMIC with Passband from 18.5 to 21.2 GHz | |
Band Pass Filter
from Marki Microwave
|
| The MFQH-00001PSM from Marki Microwave is a Passive Bandpass Filter MMIC with a passband from 18.5 to 21.2 GHz. It has a center frequency of 19.8 GHz with an insertion loss of 3.2 dB (at the center frequency) and provides a stopband suppression of up to 62 dB. This reflectionless BPF provides excellent return loss for rejected signals as well as in the passband and is suitable for applications that demand high signal fidelity. |
| |
Download Datasheet
Product Details | |
|
|
|
| CMOS Crystal Oscillator from 3 to 60 MHz for Small-Scale Design Applications | |
XO
from Taitien
|
| The O3 Type from Taitien is a Crystal Oscillator that operates from 3 to 60 MHz. It provides a CMOS clock output with frequency stability of ±50ppm (temperature range from -40°C to +105°) and supports tri-state enable/disable mode. This oscillator has a rise/fall time of 10 ns and a startup time of less than 2 ms. It requires a DC supply of 1.8/2.5/3.3 V, consumes less than 15 mA of current during normal operation, and 10 µA of current standby mode. |
| |
Download Datasheet
Product Details | |
|
