| New RF and Microwave Products this Week . |
|
|
| Surface-Mount Bandpass Filter with Passband from 47.2 to 48.2 GHz | |
Band Pass Filter
from Knowles
|
| The B479KB0S from Knowles is a Bandpass Filter with a passband from 47.2 to 48.2 GHz and a center frequency of 47.9 GHz. It has a passband insertion loss of less than 4.25 dB with out-of-band rejection of more than 40 dB (low-side) and 20 dB (high-side). This AS9100-certified filter utilizes DLI’s low-loss temperature-stable materials, offering small size and minimal performance variation over temperature. |
| |
Download Datasheet
Product Details | |
|
|
|
| mmWave Waveguide Signal Source from 275 to 295 GHz | |
Frequency Synthesizer
from ACST GmbH
|
| The 1225D-SE from ACST GmbH is a mmWave Signal Source with a frequency range from 275 to 295 GHz. It has an integrated voltage-controlled oscillator (VCO) that can generate mmWave signals with an output power of +11 dBm. This signal source has V-tune ports to set the output signal frequency by tuning the voltage from 0.8 to 5 V. It has a modular design with plug-and-play operation and does not require any adjustment for proper operation. |
| |
Download Datasheet
Product Details | |
|
|
|
| Bootstrap Phase Lock Oscillator from 80 to 130 MHz | |
Oscillator
from Quantic Wenzel (Wenzel Associates, Inc.)
|
| The Golden VHF Bootstrap Phase Lock Oscillator (PLO) from Quantic Wenzel has an output frequency from 80 to 130 MHz (100 MHz standard). This ultra-low phase noise oscillator has a low-g sensitivity of better than 5e-11/g below 300 Hz offsets, and 5e-12/g sensitivity above 300 Hz when vibration isolation is included. It consists of two rugged OCXOs of the same frequency phase locked together. |
| |
Download Datasheet
Product Details | |
|
|
|
| Variable Positive Slope Equalizer from 850 to 3150 MHz | |
Gain Equalizer
from ETL Systems
|
| The VEQUS6P-457013 from ETL Systems is a Variable Positive Slope Equalizer that operates in the S-band from 850 to 3150 MHz. It has a slope range from 0 to 10 dB and an insertion loss of less than 11 dB. This slope equalizer enables slope control by setting the DC voltage between 0 and 5 V via a feedthrough pin. It is available in a module that measures 83.11 x 32.54 x 16.00 mm with 50-ohm (SMA/N-type/BNC) or 75-ohm (BNC/F-type) connectors. |
| |
Download Datasheet
Product Details | |
|
|
|
| 50 dB Dual-Directional Coupler from 20 MHz to 1 GHz | |
Dual Directional Coupler
from Innovative Power Products
|
| The IPP-8070 from Innovative Power Products is a Dual-Directional Coupler (DDC) that operates from 20 to 1000 MHz. This 50 dB coupler has a directivity of more than 20 dB and an insertion loss of less than 0.3 dB. It can handle an input power of up to 200 W and has a VSWR of less than 1.30:1. The coupler is available in a surface-mount package that measures 31.750 x 19.050 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
| 8-Way Power Divider from 0.5 to 6 GHz | |
Power Divider
from Werbel Microwave
|
| The WM8PD-0.5-6-S from Werbel Microwave is an 8-Way Power Divider that operates from 0.5 to 6 GHz. It can handle CW input power up to 30 W, provides more than 20 dB of isolation, and has an insertion loss of less than 2.9 dB. This power divider has an amplitude unbalance of ±0.4 dB and a phase unbalance of less than ±12°. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
| 20 dB Fixed Attenuators from DC to 110 GHz | |
Fixed Attenuator
from SHF Communication Technologies
|
| The ATT110 A Series from SHF Communication Technologies are Fixed Attenuators that operate from DC to 110 GHz. They are available in different attenuation configurations up to 20 dB (3 dB, 6 dB, 10 dB and 20 dB) and can handle up to 1 W of power. These attenuators have a small footprint which makes them suitable for differential applications, where signals entering or leaving close-spaced connectors need to be attenuated simultaneously. |
| |
Download Datasheet
Product Details | |
|
|
|
| 7/16 Inner DC Block from 400 MHz to 2.5 GHz | |
DC Block
from MECA
|
| The 590-11 from MECA is an inner DC block which operates from 400 to 2500 MHz. It has a Breakdown voltage of 2500 V and can handle an input power of 500 W (2500 Peak Power). The 590-11 has an insertion loss of 0.30 dB and a VSWR of 1.40:1. This connectorized module is available with 7/16 DIN Male/Female connectors and has an operating temperature range from -50°C to +85°C. |
| |
Download Datasheet
Product Details | |
|
|
|
| SP4T Switch from 10 MHz to 8.5 GHz for 5G mMIMO Applications | |
RF Switch
from pSemi, A Murata Company
|
| The PE42445 from pSemi is an SP4T RF Switch that operates from 10 MHz to 8.5 GHz. It provides an isolation of more than 52 dB and has an insertion loss of less than 1 dB. This switch consists of four symmetric RF ports with very high isolation and has a switching time of 200 ns. It is manufactured on pSemi’s UltraCMOS process, a patented variation of Silicon-on-Insulator (SOI) technology, and delivers the performance of GaAs with the economy and integration of conventional CMOS. |
| |
Download Datasheet
Product Details | |
|
|
|
| Absorptive SPST PIN Diode Switch from DC to 18 GHz | |
RF Switch
from Quantic PMI (Planar Monolithics)
|
| The P1T-DC40G-65-T-292FF-1NS-OPT18G from Quantic PMI is an Absorptive SPST PIN Diode Switch that operates from DC to 18 GHz. It has a switching time of less than 6 ns and provides more than 55 dB of isolation. This switch can handle an input power of up to 17 dBm, has an insertion loss of less than 5 dB and a VSWR of 2.0:1. |
| |
Download Datasheet
Product Details | |
|
|
|
| 4 kW Pulsed SSPA from 1 to 2 GHz | |
RF Amplifier
from Exodus Advanced Communications
|
| The AMP2043P-4KW from Exodus Advanced Communications is a Solid-State Pulsed Power Amplifier that operates from 1 to 2 GHz. It delivers a saturated pulsed output power of more than 4 kW with a gain of over 66 dB. The amplifier has a pulse width of up to 100 usec, 6% duty cycle and rise/fall time of less than 50 ns. |
| |
Download Datasheet
Product Details | |
|
|
|
| GaN on SiC Power Amplifier from 700 to 2500 MHz | |
RF Amplifier
from RFHIC
|
| The RWP15080-10 from RFHIC is a GaN on SiC Power Amplifier that operates from 700 to 2500 MHz. It delivers an output power of 100 W (50 dBm) with a gain of 53 dB and a power-added efficiency of up to 48.31%. This amplifier has an input return loss of 9 dB and harmonics of less than -62.21 dBc (2nd harmonics) & -69.88 dBm (3rd harmonics). |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by DigiKey | | BeagleV-Fire® | | Beagleboard.org's BeagleV-Fire® features 2 GB RAM, 16 GB eMMC, 1 Gb Ethernet connection, and one M.2 E-Key PCIe connector for a wide range of applications. Click here to learn more. | | | |
|
|
| 3U OpenVPX Multi-Channel Programmable Digital Transceiver | |
RF Transceiver
from Mercury Systems
|
| The EnsembleSeries™ DCM3220 from Mercury Systems is a Multi-Channel Programmable Digital Transceiver optimized for SWaP-constrained environments. It consists of FPGA processing (Virtex Ultrascale VU7P FPGA, Zynq Ultrascale ZU11EG MPSoC, and 7488 DSP slices), VITA 65 backplane, 12-bit ADC and DAC, VITA 67 configurable rear I/O, security engine, and an AS9100D-qualified IPMI controller. |
| |
Download Datasheet
Product Details | |
|
|
|
| 6-Port Vector Network Analyzer from 300 kHz to 9 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The SN5090-6 from Copper Mountain Technologies is a 6-port Vector Network Analyzer that operates from 300 kHz to 9 GHz. This VNA utilizes precise calibration methods with an automatic calibration mechanism to measure signal parameters with the smallest uncertainty and efficiently characterize various active and passive Device Under Tests (DUTs). |
| |
Download Datasheet
Product Details | |
|
|
|
| 2.4/5/6 GHz Band Wireless Connectivity Test Set for WLAN Devices | |
RF Test Set
from Anritsu
|
| The MT8862A from Anritsu is an Advanced One-Box Wireless Connectivity Set for WLAN testing that operates in the 2.4, 5, and 6 GHz bands. It is used to measure the Tx/Rx characteristics in WLAN (IEEE 802.11a/b/g/n/ac/ax/be) devices over a bandwidth from 20 to 160 MHz. This test set uses the network mode to conduct Tx power, modulation accuracy, and other parametric measurements in realistic operating conditions. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low-Power Miniature OCXO from 8 to 150 MHz | |
OCXO
from Dynamic Engineers
|
| The OCXO3307AW from Dynamic Engineers is an Oven Controlled Crystal Oscillator (OCXO) that operates from 8 to 150 MHz. It provides an HCMOS (TTL) or Sinewave output waveform with an SSB phase noise of -172 dBc/Hz (at 100 kHz offset) and a frequency stability of ±1 ppb (vs. temperature). This OCXO has a warm-up time of 60 seconds and a rise/fall time of less than 10 ns. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| WR-75 Waveguide to N-Type / SMA Adapter from 10.7 to 12.75 GHz | |
Waveguide to Coax Adapter
from AmpliTech, Inc.
|
| The AA75X-2-1 from AmpliTech is a WR-75 Waveguide Interface to N-Type (female)/SMA Adapter with a frequency range from 10.7 to 12.75 GHz. It has a WR-75 waveguide interface size coupled with a precision tolerance U square cover flange with a gasket groove. The coaxial end of this adapter can be specified to be an N-type female connector or SMA connector. |
| |
Download Datasheet
Product Details | |
|
|
|
| Wideband Multi-Channel Satellite Link Simulator | |
Satellite Link Emulator
from Square Peg Communications Inc
|
| The RLS-2100 from Square Peg Communications is a comprehensive satellite channel simulator with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full-motion support and integrated GPS simulators. It can provide end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. |
| |
Download Datasheet
Product Details | |
|
|
|
| AWGN Noise Sources from 10 MHz to 110 GHz | |
Noise Source
from Noisecom
|
| The NC3000 Series from Noisecom are AWGN Noise Sources that operate from 10 MHz to 110 GHz. They are ideal for receiver testing, noise figure measurements, and any application requiring broad bandwidths and fast switching times. These Noise Generators deliver ENR noise output from 23 to 27 dB and have a noise output variation of less than 0.01 dB/°C. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low-Power Multi-Core Bluetooth 5.2 SoC for Wearable Applications | |
Wireless Chipset
from Renesas
|
| The DA14592 from Renesas is a Multi-Core Wireless Bluetooth Low Energy (BLE) 5.2 System-on-Chip (SoC). It consists of the latest ARM Cortex M33 application processor with a floating-point unit (FPU), advanced power management functionality and a cryptographic security engine. This SoC also has analog/digital peripherals, a software configurable protocol engine with a BLE 5.2-compliant radio, and a memory unit (96 KB of RAM, 16 KB of cache RAM, and 288 KB of ROM with embedded flash and Bluetooth LE stack). |
| |
Download Datasheet
Product Details | |
|
|
|
| 3GPP Rel-17 5G RedCap Modules for IoT Applications | |
Cellular Module
from Quectel
|
| The RG255G Series from Quectel are 5G RedCap Modules. They are based on the 3GPP Release 17-compliant RedCap technology and support both LTE Cat 4 and 5G Sub-6 GHz standalone (SA) modes, providing efficient 4G/5G global coverage. These modules are backward compatible with Release 15 and 16 networks and partial compatibility with Quectel’s 4G EG2x/EC2x series 4G modules with smaller sizes. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1-4 dB Fixed Attenuators with 3.5 mm Connectors from DC to 26.5 GHz | |
Fixed Attenuator
from Pasternack Enterprises Inc
|
| The PE7471-X Series from Pasternack are Fixed Attenuators that operate from DC to 26.5 GHz. They have an in-line, resistive PI attenuator pad design and are available in attenuation values from 1 to 4 dB. These attenuators can handle an input power of up to 2 W and have a VSWR of 1.45:1. They are ideal for reducing the power levels of a signal by a fixed amount with little or no reflections in amplifiers, receivers and detectors. |
| |
Download Datasheet
Product Details | |
|
|
|
| Multi-Layer Ceramic Capacitor for High-Speed 5G Communication Circuits | |
RF Capacitor
from Murata
|
| The GJM022 from Murata is a Multi-Layer Ceramic Capacitor (MLCC) that is designed for high-speed 5G communication circuits. It has a high Q-factor, a low equivalent series resistance (ESR), and a voltage rating of 100 V. This capacitor is manufactured using state-of-the-art thin layer forming and high-precision laminating technologies, enabling miniaturization while not compromising on performance. |
| |
Download Datasheet
Product Details | |
|
|
|
| Adhesive-Mount Omnidirectional PCB Antenna from 698 to 2700 MHz | |
Antenna
from TE Connectivity
|
| The 2118308-1 from TE Connectivity is a PCB Antenna that operates from 698 to 2700 MHz. This linearly polarized antenna has an omnidirectional radiation pattern, provides a peak gain of 3.9 dBi, and has a VSWR of less than 3.0:1. It is available in an adhesive-mount package that measures 110.0 x 14.0 x 1.31 mm with MHF, MHF1, U.FL and UMCC connection options. |
| |
Download Datasheet
Product Details | |
|
