| New RF and Microwave Products this Week . |
|
|
| 4x4 Butler Matrix from 2.4 to 8 GHz for Multi-Channel MIMO Testing | |
Butler Matrix
from Ranatec
|
| The RI 3041 from Ranatec is a 4x4 Butler Matrix that operates from 2.4 to 8 GHz. It can be used to control a beamforming network by switching the direction of beams to the desired beam port. In transmit mode, it delivers the full power of the transmitter to the beam, and in receive mode, it collects the signal from each of the beam directions with the full gain of the antenna array. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Active Balun from 40 MHz to 60 GHz for High Data Rate Applications | |
Balun
from SHF Communication Technologies
|
| The SHF BLN60 A from SHF Communication Technologies is an Active RF Balun that operates from 40 MHz to 60 GHz. It converts a single-ended signal into a clean differential waveform with a phase balance of ±2.5° and an amplitude balance of ±0.3 dB. The active configuration amplifies the input signal. This balun has an option for low-frequency compensation (LFC) that reduces the frequency response roll-off. |
| |
Download Datasheet
Product Details | |
|
|
|
| 20 W S-Band Power Amplifier from 2 to 4 GHz | |
RF Amplifier
from ERZIA
|
| The ERZ-HPA-0200-0400-43 from ERZIA is a Power Amplifier that operates from 2 to 4 GHz. It delivers a saturated output power of 20 W (~43 dBm) with a small signal gain of 43 dB and a gain flatness of ±1 dB. This amplifier has an ON/OFF time of 150/350 ns and a VSWR of less than 1.8:1. It requires a DC supply of 28 V and consumes 105 W of power. |
| |
Download Datasheet
Product Details | |
|
|
|
| Compact Software Defined Radios from 45 MHz to 6 GHz | |
Software Defined Radio
from Epiq Solutions
|
| The Matchstiq Z Series from Epiq are Software Defined Radios that operate from 45 MHz to 6 GHz. They have bandwidths of up to 50 MHz per channel and include 1 transmitter and up to 2 receivers. These SDRs are RF transceivers plus signal processing solutions and are ideal for on-the-go signal processing applications. They are based on an AMD Zynq Ultrascale+ XCZU3EG or AMD Zynq XC7Z010-2I SoC. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
| Up-Down Converter and Beamformer for 5G mmWave Applications | |
RF Up-down Converter
from Analog Devices
|
| The ADMV1239 from Analog Devices is an Up-Down Converter and Beamformer that operates from 37 to 43.5 GHz. It integrates a 16 (2x8) channel beamformer paired with a 2 transmit (TX) and 2 receive (RX) channel upconverter/downconverter (UDC). This RFIC has on-chip transmit-receive switches that connect the upconverter RF output and downconverter RF input for each polarization into eight independent channels via the 1x8 power splitters/combiners. |
| |
Download Datasheet
Product Details | |
|
|
|
| Bandpass Filter MMIC with Passband from 10.5 to 13.15 GHz | |
Band Pass Filter
from AmpliTech
|
| The AGM-010 from AmpliTech is an MMIC Band Pass Filter with a passband from 10.5 to 13.15 GHz. It can handle an input power of 20 dBm (0.1 W) and has an insertion loss of 2.9 dB in the passband. This 50-ohm filter provides over 30 dB of rejection above and below the passband. It is available as a bare die that measures 1.00 x 0.750 x 0.1 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2-Way Power Divider from 0.5 to 26.5 GHz | |
Power Divider
from Werbel Microwave
|
| The WM2PD-0.5-26-S from Werbel Microwave is a 2-way Power Divider that operates from 0.5 to 26.5 GHz. It can handle a CW input power of up to 10 W, provides an isolation of more than 14 dB, and has an insertion loss of less than 2.3 dB. This power divider has an amplitude balance of ±0.24 dB and a phase balance of ±6°. It exhibits an excellent VSWR performance over an operating temperature range from -55°C to +85°C. |
| |
Download Datasheet
Product Details | |
|
|
|
| 40 Watt, 3-Way Power Divider from 380 to 960 MHz | |
Power Divider
from MECA
|
| The 803-2-0.670 from MECA is a 3-way power divider that operates from 380 to 960 MHz covering all the Public Safety bands. It can handle up to 40 watts of power, has an insertion loss of under 1 dB and isolation over 13 dB. The power divider is available in a module with SMA Female connectors and is ideal for enterprise & public safety networks such as UHF, VHF, 700 MHz & Cell bands. |
| |
Download Datasheet
Product Details | |
|
|
|
| Compact IQ Receiver with Sub-Harmonic Mixer from 140 to 164 GHz | |
Receiver
from AT Microwave
|
| The AT-DRX-140164HG from AT Microwave is a Compact IQ Receiver that operates from 140 to 164 GHz. It has an LO frequency of 11.6 to 13.67 GHz. The LO link has a 6x amplified multiplier chain (AMC) that results in an IF frequency from DC to 6 GHz. This IQ receiver has a sub-harmonic mixer with high image rejection, low input/output return loss and flat conversion response. |
| |
Download Datasheet
Product Details | |
|
|
|
| Block Upconverter with Flexible Module Configurations from 12.75 to 14.5 GHz | |
Block Up Converter
from ETL Systems
|
| The FN-U-K1L1-24407 (Falcon2) from ETL Systems is a Block Upconverter (BUC) that converts input frequencies from 1150 to 2150 MHz to output frequencies from 12.75 to 14.5 GHz. It provides a conversion gain of up to 35 dB with a gain step size of 0.25 dB and has a noise figure of less than 12 dB. This BUC has a phase noise of -110 dBc/Hz (at 1 MHz offset) and provides an image rejection of more than 60 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| L1/L2-Band Military-Grade GPS-Disciplined Rubidium Clock | |
Rubidium Oscillator
from AccuBeat
|
| The AR51-07 from AccuBeat is a GPS-Disciplined Rubidium Clock that operates in the L1 and L2 GPS bands. It can be phase-locked to the GPS signal or other external inputs with a timing accuracy of ±20 ns (RMS) and a frequency accuracy of ±2 x 10-12. This clock generates outputs that are derived from the Rubidium-Atomic-Standard to maintain accurate time and frequency even when GPS reception is interrupted. |
| |
Download Datasheet
Product Details | |
|
|
|
| O-RAN Optimised Miniature OCXO with Extended Holdover | |
OCXO
from Rakon
|
| The E2OCXO from Rakon is an Oven Controlled Crystal Oscillator (OCXO) that enhances existing synchronization capabilities on a network synchronizer evaluation board by adding frequency error exchange processing and aging compensation to the system. It uses an Error Exchange Synchronisation technique designed to significantly enhance the capability of OCXO holdover by using a network processor and a synchronization PLL available in IEEE 1588 implementations. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| RF Analog Signal Generators from 9 kHz to 6 GHz | |
Signal Generator
from Keysight Technologies
|
| The N5171B EXG X-Series from Keysight Technologies are RF Analog Signal Generators with a frequency range from 9 kHz to 6 GHz. They provide a sine, square, triangle and positive/negative ramp waveform with an SSB phase noise of -133 dBc/Hz (at 20 kHz offset) and a frequency resolution of 0.001 Hz. These signal generators can perform basic parametric testing of components and functional verification of receivers with industry-leading output power. |
| |
Download Datasheet
Product Details | |
|
|
|
| Automotive-Grade LTE Cat-4 Module for IoT and M2M Applications | |
Cellular Module
from Cavli Wireless
|
| The AQ20 from Cavli Wireless is an Automotive-Grade LTE Cat 4 Module for IoT and M2M applications. It has built-in support for multi-constellation GNSS with Qualcomm IZat location technology for precise and dependable positioning. This module supports VoLTE and SMS over IMS/SG/CS and a wide set of Internet protocols. It is available in two variants: the AQ20-EA for the Europe and Asia markets and the AQ20-NA for the North American market. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2.4/5 GHz Wi-Fi 4 + Bluetooth 5.2 Combo SoC | |
RF Module
from NXP Semiconductors
|
| The IW416 from NXP Semiconductors is a 2.4/5 GHz Wi-Fi 4 and Bluetooth 5.2 Combo SoC. It has an independent ARM-based 160 MHz Wi-Fi and 128 MHz Bluetooth CPUs with integrated transmit (Tx) PAs, receive (Rx) LNAs and Tx/Rx switches for the Wi-Fi and Bluetooth radios. This SoC supports single-antenna operation or dual-antenna configuration which enables simultaneous Wi-Fi and Bluetooth operation with Dynamic Rapid Channel Switching (DRCS). |
| |
Download Datasheet
Product Details | |
|
|
|
| Compact and Cost-Effective Signal Generator from 9 kHz to 3.2 GHz | |
Signal Generator
from Rohde & Schwarz
|
| The R&S®SMC100A from Rohde & Schwarz is a Signal Generator with a frequency range from 9 kHz to 1.1 GHz/3.2 GHz. It supports AM/FM/FM/pulse modulation functions and has an internal modulation and pulse generator to supply the required modulation signals. This signal generator has an SSB phase noise of -105 dBc (at 20 kHz offset, 1 GHz frequency) and non-harmonics of better than -60 dBc. |
| |
Download Datasheet
Product Details | |
|
|
|
| 27 GHz Non-Magnetic Field-Replaceable SMA Connectors | |
RF Connector
from Signal Microwave
|
| The FRF27-005NM-12 from Signal Microwave are 27 GHz Non-Magnetic Field-Replaceable SMA Connectors. They consist of standard 2 and 4-hole flange connectors with a rear socket for 12 mil pins. These connectors have phosphor bronze housing (gold-plated, no nickel), beryllium copper center contacts (gold-plated, no nickel), and an Ultem dielectric bead. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 20 W, 20 dB Dual-Directional Coupler from 0.7 to 14 GHz | |
Dual Directional Coupler
from KRYTAR
|
| The 500714020 from KRYTAR is a Dual-Directional Coupler that operates from 0.7 to 14 GHz. This 20 dB coupler provides a directivity of 14 dB and has an insertion loss of 1.5 dB. It can handle an average input power of 20 W and a peak input power of 3 kW. This 4-port coupler is a combination of two 3-port couplers having their main lines cascaded and enables monitoring of forward and reflected power. |
| |
Download Datasheet
Product Details | |
|
|
|
| Omnidirectional Flexible Planar Dipole Antenna from 863 to 928 MHz | |
Antenna
from Ezurio
|
| The FlexDIPOLE from Laird Connectivity is a Flexible Planar Dipole Antenna that operates from 863 to 870 MHz and 902 to 928 MHz. This linear polarized antenna has an omnidirectional radiation pattern with a peak gain of 2.4 dBi and a VSWR of less than 3.0:1. It has an innovative design for mounting featuring adhesive backing, allowing for easy and flexible installation in a variety of enclosures and end product designs. |
| |
Download Datasheet
Product Details | |
|
|
|
| Compact 2.4 GHz SMT Antenna for Wearable Applications | |
Antenna
from AntennaWare
|
| The BodyWave™ 2.4 GHz Antenna (AW-BW-24-V2) from AntennaWare is designed for wearable applications. It solves the issue of body blocking by generating waves that flow efficiently around the body and support a communication link even when the body is blocking the signal. This antenna utilizes the unique BodyWave™ propagation, which enables wireless communications when there is no direct line of sight with on-body and off-body receivers. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
