PREV 5th July, 2017 NEXT

New RF & Microwave Products this Week

5 July, 2017 - everything RF Newsletter
 
everything RF
Date: 5 July, 2017
 
Sponsored by MECA
 
 
 
New RF Products this Week
RF Amplifier
C-band Solid State Bi-directional Amplifier from 4.4 to 4.9 GHz

RF Amplifier from NuWaves Engineering

The NW-BA-C-20-RX01 from NuWaves is a C-band Solid State Bi-directional Amplifier that operates from 4.4 to 4.9 GHz. This new Bi-Directional Amplifier offers the performance of a traditional power amplifier coupled with a low noise amplifier for receive mode, providing an amplification solution in one miniaturized package for half-duplex transceivers.
 
Download Datasheet | Product Details
 
RF Mixer
30 to 46 GHz Double Balanced Mixer Die

RF Mixer from Custom MMIC

The CMD261 is a general purpose double balanced mixer die with a RF frequency from 30 and 46 GHz. It has a low conversion loss of 8 dB, high LO to RF isolation of 30 dB, and a high input P1dB of 12 dBm across the bandwidth. The CMD261 can be used in both up/down converting systems and can be configured as an image reject mixer or single sideband modulator with external hybrids and power splitters.
 
Download Datasheet | Product Details
 
RF Variable Attenuator
10 MHz to 1.5 GHz Voltage-Controlled Variable Attenuator

RF Variable Attenuator from Skyworks

The SKY12239-11 from Skyworks is a voltage-controlled variable attenuator that operates from 10 MHz to 1.5 GHz. It has an attenuation range of up to 51 dB and an insertion loss of less than 3 dB. The attenuator has a control voltage range from 1 to 5 V. This attenuator consists of four matched PIN diodes that are biased using an external control voltage signal.
 
Download Datasheet | Product Details
 
RF Switch
200 mW Reflective SPDT Switch from 100 MHz to 40 GHz

RF Switch from Kratos

The F9025 from Kratos is a reflective SPDT switch that operates from 100 MHz to 40 GHz. It provides an isolation of over 40 dB with an insertion loss of under 5.3 dB and has a switching time of less than 250 nsec. The switch can handle a power of up to 200 mW CW or pulse and requires a supply voltage of -15 to 5 V while consuming less than 75 mA of current.
 
Download Datasheet | Product Details
 
Antenna Analyzer
Fast & Efficient One-Port Cable and Antenna Analyzer

Antenna Analyzer from Rohde & Schwarz

The R&S Cable Rider ZPH from Rohde & Schwarz is a one-port analyzer that operates from from 2 MHz to 3 GHz/4 GHz. The analyzer can make fast and accurate measurements in a single step with a speed of 0.3 milliseconds per data point and eliminates human errors. It also has a super fast boot and warm-up time, allowing it to start taking measurements just over a minute after being turned on.
 
Download Datasheet | Product Details
 
Bias Tee
10 W Bias Tee from 150 KHz to 1000 MHz

Bias Tee from UMCC

The BT-1150-LS is a Bias Tees from UMCC that operates from 150 KHz to 1000 MHz. It has a low insertion loss of less than 0.5 dB, an isolation of over 40 dB and a VSWR of 1.25:1 through the band. The bias tee can regulate a bias voltage of up to 50 V and a bias current of up to 600 mA. It can handle up to 10 Watts of RF power.
 
Download Datasheet | Product Details
 
Sponsored by MECA
Attenuators
3 dB Low PIM Attenuators
MECA has a line of Low PIM 3 dB Attenuators in both 50 & 100 watt models with a Typical PIM spec of -161 dBc. These attenuators are available with a number of connector types which include 4.1/9.5, 7/16 & Type N as well as 4.3/10.0 DIN connectors. All of the attenuators operate from 0.698 to 2.7 GHz. They are made in USA and have a 36-month warranty! Click here to learn more.
 
 
 
RF Module
Standalone and Serial-to-Wi-Fi b/g/n Module with Integrated Antenna

RF Module from STMicroelectronics

The SPWF04 is a small cloud compatible Wi-Fi module that has been developed for IoT and M2M applications. This module provides advanced Internet-security and application protocols, and feature a microcontroller capable of supporting operation in standalone or serial-to-Wi-Fi modes Cloud-Compatible Wi-Fi Modules.
 
Download Datasheet | Product Details
 
Voltage Controlled Oscillator
VCO for Low Noise Fixed Wireless Equipment from 3050 to 3070 MHz

Voltage Controlled Oscillator from Z-COMM

The CRO3060A-LF from Z-Communications operates from 3050 to 3070 MHz with a tuning voltage range of 0.5 to 4.5 Vdc and tuning sensitivity of 14 MHz/V. The RoHS compliant CRO3060A-LF delivers +4 dBm of output power into a 50 ohm load while operating off a 5 Vdc supply and drawing only 20 mA of current.
 
Download Datasheet | Product Details
 
Antenna
3.5 GHz CBRS Magnetic Mount Antenna for 5G and WIMAX

Antenna from 2J Antennas

The 2J3757M is a CBRS magnetic mount antenna that operates from 3300 to 3900 MHz with linear polarization. It delivers a gain of 2.1 dBi with an efficiency of 38.9% and can handle an input power of 35 W. The low profile antenna measures 30.9 x 71.5 mm and is available with customizable cable and connector.
 
Download Datasheet | Product Details
 
Receiver
Quad-Channel, 14-Bit, 1-GSPS Telecom Receiver IC

Receiver from Texas Instruments

The ADS58J64 from Texas Instruments is a low-power, 14-bit, 1-GSPS, quad-channel, telecom receiver device. It supports a JESD204B serial interface with data rates up to 10 Gbps with one lane per channel. The receiver provides excellent spurious-free dynamic range (SFDR) over a large input frequency range while consuming power of up to 625 mW/Ch.
 
Download Datasheet | Product Details
 
GNSS Module
Untethered Dead Reckoning GNSS Module With 3D Inertial Sensors

GNSS Module from u-blox AG

The NEO-M8U module from u-blox is a Untethered Dead Reckoning (UDR) GNSS module with integrated 3D inertial sensors. It provides continuous navigation without requiring speed information from the vehicle. The NEO-M8U may be installed in any position within the vehicle without configuration. The on-board accelerometer and gyroscope sensors result in a fully self-contained solution free from any electrical connection to the vehicle.
 
Download Datasheet | Product Details
 
RF Variable Attenuator
GaAs MMIC Voltage-Variable Attenuator from 5 to 26.5 GHz

RF Variable Attenuator from Analog Devices

The HMC712ALP3CE from ADI is an absorptive Voltage Variable Attenuator (VVA) that operates from 5 to 26.5 GHz. It has an attenuation range of 28 dB and can handle up to 28 dBm of input power. The ROHS complaint attenuator has two shunt-type attenuators which are controlled by two analog voltages, Vctrl1 and Vctrl2.
 
Download Datasheet | Product Details
 
Sponsored by MECA
 
 
 
XO
Ultra Low Jitter Crystal Oscillator from 0.2 to 1500 MHz

XO from Silicon Labs

The Si545 from Silicon Labs is a crystal oscillator that provides an ultra-low jitter, low phase noise clock at an output frequency from 0.2 to 1500 MHz. The device has a less than 1 ppb resolution and has excellent power supply noise rejection due to on-chip power supply filtering.
 
Download Datasheet | Product Details
 
RF Amplifier
Ultra-Low Noise Amplifier from 0.7 to 2.7 GHz

RF Amplifier from Guerrilla RF

The GRF2071 is a broadband, linear, ultra-low noise amplifier that can be tuned from 0.7 to 2.7 GHz. At 1.9 GHz, it provides a gain of 19.0 dB with a noise figure of 0.35 dB. The LNA delivers a P1dB of 3 dBm, IIP3 of 20 dBm while operating at 5 volts and consuming 55 mA of current. It is available in an ultra-small 2 x 2 mm DFN-8 package and is ideal for small cells, cellular boosters, wireless infrastructure, military grade GPS and DAS applications.
 
Download Datasheet | Product Details
 
RF Cable Assembly
Low Loss RF Cable Assemblies up to 50 GHz

RF Cable Assembly from MegaPhase

The GrooveTube from MegaPhase are low loss cables that operate up to 50 GHz. The cables provide high shielding effectiveness and can be used to make cable assemblies with 1.85 mm, 2.4 mm, 2.92 mm, 3.5 mm, Type-N, TNC, SMA and several other connectors. These cables are ideal for phased array radars, electronic warfare radar systems, and high reliability interconnects applications.
 
Download Datasheet | Product Details
 
DC Block
Low PIM DC Block from 698 MHz to 2.7 GHz

DC Block from Kaelus

The DCB0003F1V1 from Kaelus is a DC Block with 7-16 Male to Female connectors that operates from 698 MHz to 2.7 GHz. It has a return loss of more than 18 dB, an insertion loss of less than 0.1 dB and can handle up to 500 watts of power with a voltage rating of 60 V. The DC block has a low passive inter-modulation (PIM) of -161 dBc.
 
Download Datasheet | Product Details
 
Termination
5 Watt SMA Termination from DC to 12.4 GHz

Termination from MECA

The 400-8 from MECA is a 50 Ohm SMA-Female termination that operates from DC to 12.4 GHz. The termination can handle up to 5 watts of average power and 3 KW peak power. It has a VSWR 1.25:1 and is ideal for use in harsh environments from low orbit space & satellite to high altitude defense applications.
 
Download Datasheet | Product Details
 
RF Spectrum Analyzer
Real Time Spectrum Analyzers from 100 kHz to 8, 18, or 27 GHz

RF Spectrum Analyzer from Berkeley Nucleonics Corporation

The RTSA7550 from Berkeley Nucleonics are real time spectrum analyzers that operates from 100 kHz to 8, 18, or 27 GHz with a real-time bandwidth of up to 100 MHz. They have all the standard features of a spectrum analyzer such as frequency controls, marker functions and multi-trace functionality. The analyzer includes a real-time trigger mode for measuring complex data signals such as Wi-Fi and LTE along with markers for tracking specific frequencies.
 
Download Datasheet | Product Details
 
About everything RF
everything RF is a product discovery platform for RF & Microwave products/Services. We list over 100,000 Products from more than 200 Companies across 200 Categories in our database and enable engineers to search for them using our customized parametric search tool.