PREV 9 Sept, 2020 NEXT

New RF and Microwave Products this Week

9 Sept, 2020 - everything RF Newsletter

New products this week. View it in your browser

 
Date: 9 Sept, 2020
 
Sponsored by Signal Hound
 
 
 
New RF and Microwave Products this Week
Directional Coupler
16 dB Directional Coupler MMIC from 2 to 22 GHz

Directional Coupler  from Marki Microwave

The MC16-0222SM from Marki Microwave is a Directional Coupler that operates from 2 to 22 GHz. It has a coupling factor of 16 dB with an insertion loss of less than 3.5 dB and provides a directivity of up to 23 dB. The coupler uses passive GaAs MMIC technology which allows the production of smaller constructions and replaces larger form factor circuit board constructions.
Download Datasheet | Product Details
Power Divider
2-Way Power Divider from 0.5 to 6 GHz

Power Divider  from Werbel Microwave

The D-2066-EC from Werbel Microwave is a 2-Way Power Divider that operates from 0.5 to 6 GHz. It can handle up to 30 W of CW input power, has an insertion loss of 0.6 dB and provides isolation of 20 dB. The power splitter has an amplitude balance of 0.2 dB, a phase balance of 2 degrees, and a VSWR of 1.35:1. It is available in a RoHS compliant module that measures 3.25 x 1.46 x 0.55 inches and has SMA-Female connectors.
Download Datasheet | Product Details
Fixed Attenuator
10 dB Fixed Attenuator from 698 to 2700 MHz

Fixed Attenuator  from MECA

The LPA50-10-17WWP from MECA is a Fixed Attenuator that operates from 698 to 2700 MHz. It provides an attenuation of 10 dB with an accuracy of ±1.3 dB and has a typical passive intermodulation distortion of -161 dBc. The device can handle up to 50 W of average and 1.5 kW of peak input power. It is available in an IP67 certified module that measures 10.20 x 4.60 x 1.99 inches with 4.3/10.0 – male and female connectors.
Download Datasheet | Product Details
Beamforming IC
24.5 to 27.5 GHz Beamforming IC for 5G-NR Applications

Beamforming IC  from Sivers IMA

The AFEVM2Q 275 from Sivers IMA is a 24.5 to 27.5 GHz Beamformer IC for dual-quad core 5G NR Applications. This RFIC has be designed for 5G dual polarized phased antenna array applications. It enables very large array configurations while limiting the number of digital interfaces required. The gain and phase of the Tx/Rx sections are individually controlled over a high-speed Low-Voltage Differential Signaling (LVDS) interface allowing on the fly beam adjustment.
Download Datasheet | Product Details
RF Switch
High Power SPDT Switch from 960 to 1220 MHz

RF Switch  from Aethercomm

The SSHPS 0.96-1.22-4000 from Aethercomm is a Symmetrical SPDT Switch that operates from 960 to 1220 MHz. It can handle up to 4 KW of peak power, provides an isolation of over 50 dB, and has a switching speed of 2 us. The switch requires a +28 Vdc supply and draws up to 485 mA of current. It can be used in a wide range of applications where high power, low loss, and excellent isolation are required.
Download Datasheet | Product Details
RF Switch
100 W SPDT Switch from 100 to 2000 MHz

RF Switch  from AMCOM Communications, Inc.

The AM012050S2-0H from Amcom Communications is an SPDT Tx/Rx Switch that operates from 100 to 2000 MHz. It provides an isolation of 50 dB between the Tx port and Rx port in transmit mode, has an insertion loss of less than 1 dB, and can handle up to 100 W (50 dBm) of CW power. The device has a switching speed of 10 microseconds.
Download Datasheet | Product Details
RF Transistor
166 W GaN HEMT from 8.4 to 9.6 GHz for X-Band Radar Applications

RF Transistor  from Wolfspeed, A Cree Company

The CGHV96130F from Wolfspeed is a GaN on SiC HEMT that operates from 8.4 to 9.6 GHz. It provides a saturated output power of up to 166 W with a power gain of over 7.7 dB and has a PAE of 42%. This GaN Internally Matched (IM) FET offers superior properties compared to gallium arsenide, including higher breakdown voltage, higher saturated electron drift velocity and higher thermal conductivity.
Download Datasheet | Product Details
Sponsored by Signal Hound
Spectrum Analyzer
20 GHz Real-Time Spectrum Analyzer with 10GbE
Signal Hound’s SM200C, maintains the dynamic range, phase noise, 1 THz/s sweep speed, and 100 kHz to 20 GHz tuning range that made the SM200B so popular, but now includes a full 160 MHz IBW available for calibrated I/Q data streaming, plus device control via 10GbE SFP+ connection. In Stock at $16,000. Click here to learn more.
 
RF Transistor
2-Stage LDMOS Doherty MMIC from 1800 to 2200 MHz

RF Transistor  from Ampleon

The BLM10D1822-60ABG from Ampleon is an LDMOS 2-Stage Integrated Doherty MMIC that operates from 1800 to 2200 MHz. It delivers up to 48.4 dBm of output power with a gain of 27.8 dB and has a drain efficiency of more than 39%. This multi-band device uses Ampleon’s state-of-the-art GEN10 LDMOS technology and can be used as a general-purpose driver for mMIMO.
Download Datasheet | Product Details
RF Amplifier
4-Stage Power Amplifier from 13.5 to 15 GHz for Ku-band VSAT Communications

RF Amplifier  from MACOM

The MAAP-011313 from MACOM is a 4-Stage Power Amplifier that operates from 13.5 to 15 GHz. It is fabricated using a GaAs pHEMT process which features full passivation for enhanced reliability and has a temperature compensated output power detector. This amplifier provides a P1dB of 34.5 dBm with a gain of 36 dB and has a PAE of 28%.
Download Datasheet | Product Details
RF Amplifier
200 W GaN HEMT Pulsed Amplifier from 9.3 to 9.7 GHz

RF Amplifier  from RFHIC

The RRM9397200-560 from RFHIC is a Pulsed GaN Amplifier that operates from 9.3 to 9.7 GHz. It delivers a pulsed output power of 200 W with a gain of 55 dB and has a PAE of 18%. The amplifier has a rise/fall time of 50 ns and a switching time of 250 ns. It is available in a module that measures 140 x 140 x 25 mm with SMA female connectors.
Download Datasheet | Product Details
RF Amplifier
8 KW TWT Pulsed Amplifier from 4 to 8 GHz

RF Amplifier  from Communications & Power Industries

The VZC3530P2 from CPI is a TWT Pulsed Amplifier that operates from 4 to 8 GHz. It delivers an output power of 8000 W with a gain of over 66 dB. The unit has a pulse width of 0.1 to 100 µs and a duty cycle of up to 6%. This modular assembly allows for either lower-powered multiple test applications or a single amplifier phase combined system of two VZC-3530J1 amplifiers.
Download Datasheet | Product Details
OCXO
Oven Controlled Crystal Oscillators from 5 to 40 MHz

OCXO  from Raltron

The OCXO SERIES 7000 from Raltron are Oven Controlled Crystal Oscillators that operate from 5 to 40 MHz. These SMD OCXOs have a phase noise of -165 dBc/Hz at 100 kHz offset and a stability of ±5 ppb over a temperature range from -40 to 85°C. The oscillators require a DC supply voltage of 3.3 V and have a warm-up time of less than 3 minutes.
Download Datasheet | Product Details
General Crystal Oscillator
32.768 kHz CMOS General Crystal Oscillator

General Crystal Oscillator  from Dynamic Engineers

The XO2520BM-32.768KHz from Dynamic Engineers is a General Crystal Oscillator that operates at a frequency of 32.768 kHz. It provides a CMOS output and has a duty cycle of up to 55%. The device requires a supply voltage of 3.3/2.5/1.8 V and consumes up to 18 uA of current. It can operate at a temperature range from -40°C to 85°C.
Download Datasheet | Product Details
Vector Network Analyzer
2-Port Vector Network Analyzer from 10 MHz to 43.5 GHz

Vector Network Analyzer  from Copper Mountain Technologies

The S5243 from Copper Mountain Technologies is a 2-Port Vector Network Analyzer that operates from 10 MHz to 43.5 GHz. It features an excellent dynamic range of 140 dB (10 Hz IF BW) and has a fast measurement speed of 15 µs. The device can be used to measure all four S parameters (S11, S21, S12, and S22) and has an output power that can be adjusted from -55 dBm to 0 dBm.
Download Datasheet | Product Details
Sponsored by Signal Hound
 
 
 
RF Amplifier
Low Noise Amplifier from 18 to 42 GHz

RF Amplifier  from ERZIA

The ERZ-LNA-1800-4200-24-6 from Erzia is a Low Noise Amplifier that operates from 18 to 42 GHz. It provides a small signal gain of over 22 dB with a noise figure of less than 6.5 dB and has a P1dB of 9 dBm. The amplifier requires 15 Volts of DC supply and consumes 1 watt of power. It is available in a gold-plated aluminum housing that measures 35.1 x 18.9 x 7.4 mm and has 2.92 mm female connectors.
Download Datasheet | Product Details
Front End Module
RF Front End Module for GPS Applications

Front End Module  from NuWaves Engineering

The NW-RF-GPS-FE from NuWaves is an RF Front End Module for GPS applications with a transmit (Tx) frequency from 1626.5 to 1675 MHz and a receive (Rx) frequency from 1518 to 1559 MHz. It delivers more than 20 W of saturated output power with a transmit gain of 43 dB and a receive gain of 47 dB. This high-performance FEM consists of an RF power amplifier, an LNA, a high isolation diplexer between the transmit and receive paths, and band-reject filters.
Download Datasheet | Product Details
RF Amplifier
GaN SSPA from 25 to 27.5 GHz for Airborne and Space Applications

RF Amplifier  from QuinStar Technology Inc

The QBP 25284025 from QuinStar Technology is a GaN-Based SSPA that operates from 25 to 27.5 GHz. It delivers a P1dB of up to 39.6 dBm with a small signal gain of over 29.1 dB and has a PAE of 23.71%. The amplifier requires a DC supply voltage of 24 V and consumes 3.5 A of current. This SSPA is available in a module that measures 6.5 x 4.75 x 1.52 inches with connectors.
Download Datasheet | Product Details
Band Pass Filter
28 GHz Surface Mount Bandpass Filter for 5G Applications

Band Pass Filter  from Knowles

The B280LA0S from Knowles is a Bandpass Filter with a passband from 27.5 to 28.5 GHz. It has an insertion loss of less than 4.5 dB and provides rejection of over 30 dB above (30 to 37 GHz) and below (DC to 26.1 GHz) the passband. The filter uses DLI's low loss temperature stable materials which enable it to offer a small size and minimal performance variation over temperature.
Download Datasheet | Product Details
Cellular IoT Module
Low Power CAT-M and NB-IoT Module for M2M Applications

Cellular IoT Module  from SIMCom

The SIM7080G from SIMCom is an LPWA module for Multi-Band CAT-M and NB-IoT. It is designed for applications that need low latency and low throughput data communication in a variety of radio propagation conditions. The module provides an uplink data rate of up to 1119 Kbps (Cat-M), 150 Kbps (NB-IoT), and a downlink data rate of up to 589 Kbps (Cat-M) and 136 Kbps (NB-IoT).
Download Datasheet | Product Details
RF Module
802.11 b/g/n Wi-Fi Module from 2.412 to 2.484 GHz

RF Module  from USR IoT

The USR-WIFI232-B2 from USR IoT is an 802.11 b/g/n Wi-Fi Module that operates from 2.412 to 2.484 GHz. It delivers a Tx power of up to 20 dBm and has a receiving sensitivity of less than -71 dBm. The device requires a DC supply of 3.3 V and consumes up to 350 mA of current. It supports bidirectional transparent data transmission between a serial TTL UART interface and the Wi-Fi network.
Download Datasheet | Product Details
Antenna
5G-NR/4G LTE/3G/2G Swivel Connector Mount Antenna

Antenna  from 2J Antennas

The 2JW1683 from 2J Antennas is a Connector Mount Antenna that operates from 617-960, 1427-2690, 3300-5000, and 5150-5925 MHz. It supports 5G-NR, 4G LTE, FirstNet, CBRS, LPWA, CAT-X/CAT-Mx, CAT-NBx, NB-IoT, 3G, and 2G standards. This linearly polarized antenna delivers a peak gain of over 0.2 dBi with an efficiency of up to 57% and can handle up to 35 W of input power.
Download Datasheet | Product Details
Antenna
Low Profile Antenna Multi-Band Antenna from 600 MHz to 6 GHz

Antenna  from PCTEL

The BMLPV5000 from PCTEL is a Low Profile Antenna that operates from 600 MHz to 6 GHz. This multi-band antenna provides 2.6 dBi gain from 689-960 MHz, 1 dBi gain from 1710-2170 MHz, 2.3 dBi gain from 3300-4200 MHz, and 3.1 dBi gain from 4900-5985 MHz. It can handle up to 150 W of power, features vertical/linear polarization, and has a VSWR of less than 3:1.
Download Datasheet | Product Details
Block Up Converter
220 W C-Band Block-Up Converter from 5.850 to 6.725 GHz

Block Up Converter  from Actox

The ABD220DC from Actox is a C-Band BUC that up-converts an input frequency from 950-1825 MHz to an RF frequency from 5.850-6.725 GHz with a LO frequency of 4.90 GHz. This BUC delivers a saturated output power of 220 watts with a gain of over 77 dB. It requires an AC supply voltage from 80 to 240 V and consumes up to 994 W of power.
Download Datasheet | Product Details
Block Up Converter
Ka-band GaN Block-Up Converter from 27.5 to 31 GHz

Block Up Converter  from ACORDE

The ACTX-Ka80W-Ex-V2 from Acorde is a Ka-Band GaN BUC that up-converts an input frequency from 950-2000 MHz to an output frequency from 27.5-31 GHz. It delivers a saturated output power of 49 dBm with a gain of more than 65 dB. This BUC consumes 600 watts of power and requires an AC supply of 85-265 V.
Download Datasheet | Product Details
Horn Antenna
Conical Horn Antenna from 8.2 to 12.4 GHz

Horn Antenna  from A-Info

The LB-CH-90-15 from A-INFO is a Corrugated Conical Horn Antenna that operates from 8.2 to 12.4 GHz. It is available in two configurations, one with a waveguide interface (WR 90) and the other with a coaxial connector interface (SMA, N, TNC, 7 mm, 3 mm). This linearly polarized antenna delivers a gain of 15 dBi and has a VSWR better than 1.5:1.
Download Datasheet | Product Details
About everything RF
everything RF keeps users up to date with the RF & Microwave Industry. We provide the latest industry news, information on new product releases, upcoming events, white papers, articles, interviews and much more.
To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]