New RF and Microwave Products this Week . |
|
|
5 W GaN Power Amplifier MMIC from 24.25 to 26.5 GHz |
RF Amplifier
from Qorvo
|
The QPA0524 from Qorvo is a Ku-Band GaN Power Amplifier MMIC that operates from 24.25 to 26.5 GHz. It delivers an output power of 37 dBm (~5 W) with a small signal gain of 23 dB and a power-added efficiency of 23%. This amplifier provides linear power of 26 dBm (~400 mW) with an ACPR of -30 dBc at 802.11ac 160 MHz MCS. |
|
Download Datasheet
Product Details | |
|
|
|
25 W Flanged AlN Terminations from DC to 7 GHz |
Termination
from Inmet by Spectrum Control
|
The 7ANT300-25 Series from Inmet by Spectrum Control are RF Terminations that operate from DC to 7 GHz. They can handle an input power of 25 W and have a VSWR of less than 1.35:1. These 50 and 100-ohm terminations consist of a proprietary thin film resistor material and are manufactured on an Aluminum Nitride (AlN) substrate. |
|
Download Datasheet
Product Details | |
|
|
|
80 W Class A/AB Solid-State Power Amplifier from 18 to 40 GHz |
RF Amplifier
from Exodus Advanced Communications
|
The AMP2145D-LC from Exodus Advanced Communications is a Solid-State Power Amplifier (SSPA) that operates from 18 to 40 GHz. It delivers a saturated output power of more than 80 W with a gain of over 49 dB. This SSPA is based on Class A/AB linear amplifier design equipped with high power advanced technology that delivers high efficiency. |
|
Download Datasheet
Product Details | |
|
|
|
Real-Time Peak USB Power Sensors from 50 MHz to 40 GHz |
RF Power Meter & Sensor
from Boonton
|
The RTP5000 Series of USB Power Sensors from Boonton are Real-Time peak power sensors that operate from 50 MHz to 40 GHz (available in 6 GHz, 18 GHz and 40 GHz configurations). They have a dynamic range from -60 dBm to +20 dBm with a measurement rate of 100,000 measurements per second, with no gaps in signal acquisition and zero measurement latency. |
|
Download Datasheet
Product Details | |
|
|
|
Vector Network Analyzer from 100 kHz to 4.5/8.5 GHz |
Vector Network Analyzer
from Rohde & Schwarz
|
The R&S®ZND from Rohde & Schwarz is a Vector Network Analyzer (VNA) designed for unidirectional measurements from 100 kHz to 4.5 GHz and bidirectional measurements up to 8.5 GHz (optional). This VNA can measure all four S-parameters (S11, S12, S21, S22) and other network parameters such as magnitude and phase of the S-parameters. |
|
Download Datasheet
Product Details | |
|
|
|
1-Port USB Vector Network Analyzer from 1 MHz to 6 GHz |
Vector Network Analyzer
from Copper Mountain Technologies
|
The R60 is a single port USB-powered VNA (Reflectometer) capable of measuring S11 from 1 MHz to 6.0 GHz. It can be operated from any Windows PC or laptop using a USB cable. The R60 provides a wide variety of analysis capabilities, including S11, time-domain with gating, DTF measurements and much more. |
|
Download Datasheet
Product Details | |
|
|
|
|
Phase-Stable and Flexible Cable Assemblies from DC to 50 GHz |
RF Cable Assembly
from Maury Microwave
|
The StabilityFlex™ from Maury Microwaves are Phase-Stable Cable Assemblies that operate from DC to 50 GHz. They are available in 24", 36", 48", and 60" lengths (custom lengths available) with N-type, SMA, 2.92mm and 2.4mm connectors. These ultra-flexible cable assemblies have a phase stability vs flexure of ±4°, amplitude stability vs flexure of ±0.05 dB, and provide shielding of more than 100 dB. |
|
Download Datasheet
Product Details | |
|
|
|
6 GHz Low-Smoke, Fire-Retardant Cable for In-Building Applications |
RF Cable
from Times Microwave Systems
|
The LMR-400-75-FR from Times Microwave Systems is an RF Cable that operates up to 6 GHz. This RF cable is a non-toxic (non-halogen), low-smoke, and fire-retardant solution that is designed for in-building runs to enable routing anywhere except air handling plenums. It is UL/NEC and CSA-rated, and also meets the requirements of MSHA-P standard for mining applications. |
|
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
|
Direct RF 3U VPX Data Converter for High-Speed Connectivity Applications |
RF Digitizer
from Mercury Systems
|
The DRF3182 from Mercury Systems is a Data Converter that is designed to directly digitize RF signals in radar, communications, and electronic warfare systems. It eliminates the need to implement RF-to-IF down conversion prior to digitization. This converter combines excellent data capture capability with powerful processing from Intel’s 14 nm Intel Stratix 10 SoC FPGA, making it suitable for applications with size, weight, and power constraints. |
|
Download Datasheet
Product Details | |
|
|
|
|
|
|
Download Magazine for Free | |
|
|
3-Way In-line Power Splitter/Combiner from 617 to 4200 MHz |
Power Divider
from Microlab
|
The D3-76FE from Microlab is a 3-Way In-line Power Splitter/Combiner that operates from 617 to 5925 MHz. This splitter can handle an average power of 50 W as a splitter and 0.2 W as a combiner and can handle a peak power of 1 kW. It provides more than 18 dB of isolation, an insertion loss of less than 1.3 dB and has a PIM of -153 dBc (tested with 2x 1900MHz, +43 dBm tones). |
|
Download Datasheet
Product Details | |
|
|
|
Power Limiter from 0.5 to 18 GHz |
Limiter
from Quantic PMI (Planar Monolithics)
|
The LM-0518-10-1W-SHS-2-FM from Quantic PMI is a Power Limiter that operates from 0.5 to 18 GHz. It can handle 100 W of peak power with a pulse width of 1 µs and a duty cycle of 1%. This power limiter has an insertion loss of 1.5 dB and a leakage level of less than +10 dBm with a VSWR of 2.0:1. It is available in a compact housing that measures 1.0 x 1.0 x 0.4 inches and has SMA male/female connectors. |
|
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
Multi-Band Active GNSS Antenna with RTK Support for cm-level Accuracy |
GNSS Module
from Taoglas
|
The EL20A from Taoglas is a Multi-Band Active GNSS Antenna solution that operates from 1200 to 1610 MHz. It combines a GNSS antenna, RF electronics, and u-blox ZED-F9P GNSS receiver to enable cm-level positioning. This solution is an energy-efficient platform that provides high-precision GNSS location for large-scale, niche navigation, and autonomous applications in an off-the-shelf, compact form factor. It supports reception of signals in the GPS, GLONASS, QZSS, Galileo, and BeiDou constellations over 184 channels. |
|
Download Datasheet
Product Details | |
|
|
|
D-band VNA Frequency Extension Module from 110 to 170 GHz |
Vector Network Analyzer Extender
from AT Microwave
|
The AT-VEX-06 from AT Microwave is a VNA Frequency Extension Module that operates from 110 to 170 GHz (D-band). It has an input RF/LO frequency range of 9.17 to 14.17 GHz and with a 12x multiplier. This extension module delivers a Tx RF output power of -5 dBm and can handle an RF source input power of +6 dBm. |
|
Download Datasheet
Product Details | |
|
|
|
Non-Blocking 4x8 Solid-State Switch Matrix from 100 kHz to 4 GHz |
Switch Matrix
from Becker Nachrichtentechnik GmbH
|
The RSWM-4X8LR from Becker RF is a 4x8 Switch Matrix that operates from 100 kHz to 4 GHz. It has four inputs and eight outputs interconnected via a non-blocking matrix where a single input can route to multiple outputs simultaneously. This switch matrix has high channel isolation to ensure that signals in adjacent radio channels do not affect each other. |
|
Download Datasheet
Product Details | |
|
|
|
8-Way Power Divider/Combiner from 2.0 to 4.2 GHz |
Power Divider
from American Microwave Corporation
|
The PDV-8W01 from American Microwave Corporation is an 8-Way Power Divider/Combiner that operates from 2.0 to 4.2 GHz. It can handle an input power of 1 W with a VSWR of less than 1.50:1. This power divider has an insertion loss of less than 1.0 dB with an isolation of more than 16 dB. It has an amplitude imbalance of 0.7 dB and a phase imbalance of less than 10 Degree. |
|
Download Datasheet
Product Details | |
|
|
|
Passive GaAs Triple Balanced Mixer MMIC from 5 to 30 GHz |
RF Mixer
from Marki Microwave
|
The MM2-0530LCH from Marki Microwave is a Passive GaAs Triple Balanced Mixer MMIC with an RF/LO frequency from 5 to 30 GHz and an IF frequency from 2 to 20 GHz. It can handle an input power of +10 dBm and has a conversion loss of 9 dB. This triple-balanced mixer has an LO-to-RF isolation of 44 dB with an input IP3 of 19 dBm. |
|
Download Datasheet
Product Details | |
|
|
|
High-Stability SMD Crystal from 8 to 125 MHz |
RF Quartz Crystal
from Dynamic Engineers
|
The XTAL6035AX from Dynamic Engineers is a High-Stability SMD Crystal that operates from 8 to 60 MHz (Fundamental) and 40 to 125 MHz (3rd Overtone). It has a frequency tolerance of ±10 to ±20 ppm with a frequency stability of ±15 to ±50 ppm. This crystal has a load capacitance from 6 to 20 pF. It is available in an SMD package that measures 6 x 3.5 x 1.2 mm and can operate over a temperature range from -40 to 85°C. |
|
Download Datasheet
Product Details | |
|
|
|
60 W, K/Ka-Band TWT Amplifier from 18 to 40 GHz |
RF Amplifier
from dB Control
|
The dB-4051 from dB Control is a K/Ka-Band TWT Amplifier that operates from 18 to 40 GHz. It delivers an output power of 50 to 60 W with a gain of over 48 dB and a gain flatness of ±3 dB. This amplifier is a periodic permanent magnet (PPM)-focused, conduction-cooled TWT amplifier that can amplify CW, AM, FM, or pulse-modulated signals. |
|
Download Datasheet
Product Details | |
|
|
|
Common Data Link for Airborne, Surface, and Maritime Applications |
Data Link
from BAE Systems
|
The iCDL from BAE Systems is a Common Data Link that operates in the Ku-Band from 14.4 to 15.35 GHz. It provides the warfighter a complete affordable solution to bring wideband wireless data link capability to airborne, surface, and maritime platforms. This data link has a programmable hardware and software radio design architecture to provide a comprehensive solution. |
|
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
InP Cryogenic Low Noise Amplifier from 4 to 8 GHz |
RF Amplifier
from Low Noise Factory
|
The LNF-LNC4_8SG from Low Noise Factory (LNF) is a Cryogenic Low Noise Amplifier (LNA) that operates from 4 to 8 GHz. It provides 40 dB of gain with a noise figure of 0.02 dB and a noise temperature of 1.5 K. This LNA is manufactured using LNF’s proprietary InP HEMT technology. It is not hermetically-sealed and therefore, it must be operated in a vacuum environment when the temperature reaches below the dewpoint. |
|
Download Datasheet
Product Details | |
|
|
|
GaAs pHEMT Low Noise Amplifier from 17 to 55 GHz |
RF Amplifier
from MACOM
|
The MAAL-011229 from MACOM is a Low Noise Amplifier that operates from 17 to 55 GHz. It delivers 24 dB of small signal gain with a noise figure of 3.2 dB and a saturated output power of 24 dBm. This amplifier has a gain flatness of ±2 dB and a return loss of 12 dB (input/output). It is fabricated using a GaAs pHEMT process which features full passivation for enhanced reliability and can be used as a low noise amplifier stage or a driver stage in higher power. |
|
Download Datasheet
Product Details | |
|
|
|
9-Port 5G Antennas from 617 to 6000 MHz with GPS/GNSS Connectivity |
Antenna
from Excelwave
|
The EAM9-4C4W1G-xx Series from Excelwave Technologies are 9-Port 5G Antennas that operate from 617 to 960 MHz and 1690 to 6000 MHz. These vertical/RHCP-polarized antennas provide a gain of 4 dBi (cellular), 5 dBi (Wi-Fi), and 3 dBi (GPS/GNSS) and have a VSWR of 2:1. They are low-profile antennas designed for transit applications and are integrated into a heavy duty radome assembly that meets the requirements for a variety of vehicles, including cars, buses, trucks, trams, and trains. |
|
Download Datasheet
Product Details | |
|
|
|
Automotive-Grade Multilayer Ceramic Capacitors up to 22 µF |
RF Capacitor
from KYOCERA AVX
|
The KAM Series from KYOCERA AVX are Multilayer Ceramic Capacitors with capacitance values from 0.5 pF to 22 µF. These AEC-Q200-qualified capacitors have a voltage rating from 4 to 3000 V and have capacitance tolerances ranging from ±1% to ±20%. The KAM Series capacitors are not only suitable for automotive industry but also for improved reliability application. |
|
Download Datasheet
Product Details | |
|