| Featured Products this Week . |
|
|
| WRD650 Double Ridge Bandpass Filter with Passband from 6 to 18 GHz | |
Waveguide Filter
from Scientific Microwave Corporation
|
| The WRD650 Bandpass Filter from Scientific Microwave Corporation is a Double Ridge Waveguide Bandpass Filter with a passband from 6 to 18 GHz. It has a passband insertion loss of 1.2 dB and provides a rejection of more than 45 dB above and below the passband. This double ridge BPF has a VSWR of 1.50:1 at the waveguide port and a VSWR of 1.60:1 at the coaxial port. |
| |
Download Datasheet
Product Details | |
|
|
|
| 70 W GaN-Based SSPA from 2 to 8 GHz | |
RF Amplifier
from Exodus Advanced Communications
|
| The AMP1146A from Exodus Advanced Communications is a GaN-based SSPA that operates from 2 to 8 GHz. This class AB amplifier delivers a saturated output power of more than 70 W with a gain of 48 dB. It has 2-tone intermodulation (IMD) of -30 dBc, harmonics of -20 dBc, and spurious of -60 dBc. The amplifier requires a DC supply of 32 V and draws 14 A of current. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2.4 mm Male RF Termination from DC to 50 GHz | |
Termination
from MECA
|
| The 469-1 from MECA is an RF Termination that operates from DC to 50 GHz. It is matched to 50 ohms and can handle an average power of 0.50 W with a VSWR of less than 1.60:1. It is available as a module that measures 0.76 x 0.3 inches and has a stainless steel 2.4 mm male connector. This termination can operate over a temperature range of -45 to 85 Degrees C. |
| |
Download Datasheet
Product Details | |
|
|
|
| Chip Attenuators with Alumina-Substrate from DC to 18 GHz | |
Fixed Attenuator
from Inmet by Spectrum Control
|
| The PCAA Series from Inmet by Spectrum Control are Powerfilm Chip Attenuators that operate from DC to 18 GHz. They are available in attenuation values from 0 to 20 dB and have attenuation stability of 0.0001 dB/dB/°C. These attenuators can handle an input power of up to 5 W and have a VSWR of less than 1.5:1. They have an operating temperature range of -55°C to +150°C. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Low Noise Cryogenic Amplifier from 6 to 8.5 GHz | |
RF Amplifier
from AmpliTech
|
| The APTC3-06000850-2K00-D2-V from AmpliTech is a Low Noise Cryogenic Amplifier that operates from 6.0 to 8.5 GHz. It has been designed for cryogenic applications down to 4K, with an industry-low Noise Figure of 25K at +296K and 2K at 4K case temperatures across the band. It provides a more than 40 dB of gain with a noise figure of less than 0.029 dB (at 4 K) and has a P1dB of -6 dBm. |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by PCB Directory | | |
|
|
| 2-Port USB Controlled VNA from 300 kHz to 9 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The SC5090 from Copper Mountain Technologies is a modular 2-port compact VNA for 2-path measurements that operates from 300 kHz to 9 GHz. It has a dynamic range of 140 dB, an output power of 15 dBm, and a typical measurement speed of 16 µs per point. The VNA has a directivity of 46 dB and can be used to measure all four S parameters (S11, S21, S12, and S22). |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Phase-Stable and Flexible Cable Assemblies from DC to 50 GHz | |
RF Cable Assembly
from Maury Microwave
|
| The StabilityFlex™ from Maury Microwaves are Phase-Stable Cable Assemblies that operate from DC to 50 GHz. They are available in 24", 36", 48", and 60" lengths (custom lengths available) with N-type, SMA, 2.92mm and 2.4mm connectors. These ultra-flexible cable assemblies have a phase stability vs flexure of ±4°, amplitude stability vs flexure of ±0.05 dB, and provide shielding of more than 100 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| Hand-Flex Coaxial Cables from DC to 40 GHz | |
RF Cable Assembly
from Mini Circuits
|
| The 086 Series of Hand-Flex Coaxial Cables from Mini-Circuits operate from DC to 40 GHz. These cables are ideal for interconnection of coaxial components or sub-systems. The cables have an insertion loss of under 2 dB and return loss of 22 dB at 40 GHz. They can handle up to 61 W of input power and have only 6 mm of bend radius. |
| |
Download Datasheet
Product Details | |
|
|
|
| Rugged, High-Temperature RF Cable for Avionics Systems | |
RF Cable
from Carlisle Interconnect Technologies
|
| The 371101 from Carlisle Interconnect Technologies is an RF Cable designed for avionics systems. It is designed to meet the performance and weight demands of all modern aircraft and meets OEM and regulatory requirements for fire safety on passenger aircraft. It uses innovative silver-plated copper-clad aluminum conductors and shields along with laser-markable jacketing for easy identification, high shield effectiveness and signal integrity, and minimal attenuation. |
| |
Download Datasheet
Product Details | |
|
|
|
| 1.85 mm PCB Compression-Mount Connector from DC to 67 GHz | |
RF Connector
from Samtec
|
| The 185-J-P-EP-ST-CM-1 from Samtec is a 1.85 mm (Jack) Compression Mount Connector that operates from DC to 67 GHz. It has a dielectric withstanding voltage (DWV) of more than 600 V(RMS) and a VSWR of less than 1.35:1. This PCB compression mount connector has a stainless-steel shell, can withstand more than 500 mating cycles and has an operating temperature range of -65°C to +125°C. |
| |
Download Datasheet
Product Details | |
|
|
|
| Electromagnetic Analysis Tool for Predicting Radar Cross Section | |
Software
from Remcom
|
| XGtd from Remcom is a Ray-Based EM Simulation Software for assessing the effects of a vehicle or vessel on antenna radiation, predicting coupling between antennas and predicting radar cross section (RCS). It incorporates techniques including Geometric Optics (GO), the Uniform Theory of Diffraction (UTD), Physical Optics (PO), and the Method of Equivalent Currents (MEC). |
| |
Download Datasheet
Product Details | |
|
|
|
| RF Shielded Test Box for Sub-6 GHz Applications | |
RF Shielded Test Enclosure
from RF Electronics
|
| The HDRF-1560-D from RF Electronics is an RF Shielded Test Box that operates at frequencies up to 6 GHz. The test box can be used to test WLAN devices, 802.11 a,b,g,n, Bluetooth, RFID and other applications that operate in the sub-6 GHz frequency band. It has a thick RF absorbing foam that dampens standing waves and reflections by providing an isolation of over 130 dB under 1 GHz and over 90 dB at 6 GHz. |
| |
Download Datasheet
Product Details | |
|
|
|
| Integer-N/Fractional-N PLL Synthesizer from 1 to 10 GHz | |
Frequency Synthesizer
from Analog Devices
|
| The ADF41510 from Analog Devices is an Integer-N/Fractional-N PLL Synthesizer that operates from 1 to 10 GHz. It is designed for implementing local oscillators (LOs) up to 10 GHz in the upconversion and downconversion sections of wireless receivers and transmitters. This synthesizer has a phase frequency detector (PFD) frequency of 250 MHz (Integer-N) & 125 MHz (fractional-N) with a phase noise of -235 dBc/Hz (Integer-N) & -231 dBc/Hz (fractional-N). |
| |
Download Datasheet
Product Details | |
|
|
|
| 4x4 Butler Matrix from 18 to 40 GHz | |
Butler Matrix
from KRYTAR
|
| The KBM9180400 from KRYTAR is a 4x4 Butler Matrix that operates from 18 to 40 GHz. It provides an isolation of more than 12 dB, has an insertion loss of less than 12 dB, and a VSWR of up to 2:1. This butler matrix has an amplitude balance of ±1.3 dB and a phase balance of ±15°. It is available in a module that measures 3.68 x 2.80 x 0.81 inches and has 2.4 mm (female) connectors. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 2.4/5 GHz Wi-Fi 6 + Bluetooth 5.2 + 802.15.4 Combo Module | |
RF Module
from Panasonic Corporation
|
| The PAN9019A from Panasonic Corporation is a 2.4/5 GHz Wi-Fi 6 + Bluetooth 5.2 + 802.15.4 Combo Module. It has been designed to allow easy integration of Wi-Fi, Bluetooth 5.2 (low-energy and long-range), and 802.15.4-based technologies into various electronic devices. This module consists of NXP’s IW612 WLAN 2.4 GHz and 5 GHz radio SoC, a dual-core CPU, a Bluetooth radio, an 802.15.4 radio, a 40 MHz crystal, an SPDT switch, a diplexer, and high-speed data interfaces. |
| |
Download Datasheet
Product Details | |
|
|
|
| Antenna Mount Solid-State Block Up-Converter from 27 to 31 GHz | |
Block Up Converter
from Spacepath Communications
|
| The STS20/40Ka from SpacePath Communications is a solid-state Block Up Converter (BUC) that converts input frequencies from 950-1950 MHz to output frequencies from 27-31 GHz. It provides more than 60 dB of gain with a gain adjustment range of 20 dB. This BUC has a phase noise of 93 dBc/Hz (at 100 kHz offset) and spurious levels of less than -55 dBc. |
| |
Download Datasheet
Product Details | |
|
|
|
| L1/L2-Band, Anti-Jamming GNSS Antenna with Sub-1 cm Accuracy | |
GPS/GNSS Antenna
from Tallysman Wireless
|
| The TW5394 from Tallysman Wireless is a Multi-band (L1/L2) GNSS Antenna. It has integrated L-Band receiver for PointPerfect PPP-RTK corrections. This antenna has been designed to provide sub-1 m (standalone), sub-6 cm (PPP-RTK corrections), and sub-1 cm (RTK corrections) accuracy to support demanding navigation, automation, and precision mobility applications. |
| |
Download Datasheet
Product Details | |
|
|
|
| MEMS-based OCXO from 60 to 220 MHz for Assured PNT systems | |
OCXO
from SiTime
|
| The SiT7102 from SiTime is a MEMS-based Oven Controlled Crystal Oscillator (OCXO) that operates from 60 to 220 MHz. It provides an LVCMOS or clipped sinewave output with a frequency stability of ±5 ppb and a time error of less than 3.0 µs time error after 12 hrs without GPS synchronization. This OCXO uses SiTime’s temperature sensing technology and advanced CMOS design to deliver exceptional stability in the presence of environmental stressors such as airflow, temperature perturbation, vibration, shock, and EMI. |
| |
Download Datasheet
Product Details | |
|
|
|
| IP65-Rated RAIN RFID Sled Reader for Dense Reader/Tag Applications | |
RFID Reader
from CAEN RFID
|
| The R13071C from CAEN RFID is a RAIN RFID Sled Reader that is ideal for long-range reading applications. It operates from 865.6 to 867.6 MHz (ETSI) and 902-928 MHz (FCC), delivers an output power of up to 1 W, and can detect tags over a read range of up to 5 m. This reader is based on the Impinj E710 IC chip that supports fast reading speeds and can be used in dense reader and tag environments. |
| |
Download Datasheet
Product Details | |
|
|
|
| Wireless Connectivity Test Platform from 380 MHz to 15 GHz | |
RF Test Set
from Keysight Technologies
|
| The E7515P UXM Wireless Connectivity Test Platform from Keysight Technologies operates from 380 MHz to 15 GHz. It has a highly integrated signalling tester with multiformat stack support, rich processing power, and abundant RF resources. This test set supports the latest 3GPP Release 15 and beyond, thereby enabling users to establish a 5G call with a device under test (DUT) in non-standalone (NSA) mode, standalone mode (SA) mode, and frequency bands FR1/FR2. |
| |
Download Datasheet
Product Details | |
|
