| New RF and Microwave Products this Week . |
|
|
| Remote Spectrum Monitors from 9 kHz to 54 GHz | |
RF Monitoring Receiver
from Anritsu
|
| The MS2720xA from Anritsu are Remote Spectrum Monitors that operate from 9 kHz to 9/14/20/26.5/32/43.5/54 GHz. They use the latest technologies to deliver accuracy and precision in measurements previously reserved only for benchtop instruments. These modules consist of a real-time spectrum analyzer (RTSA) that has a measurement bandwidth of 110 MHz and a point of intercept (POI) time of 2.05µs. |
| |
Download Datasheet
Product Details | |
|
|
|
| Handheld Real-Time Spectrum Analyzers from 9 kHz to 9.5 GHz | |
RF Spectrum Analyzer
from HAROGIC Technologies
|
| The PXE-90 from HAROGIC Technologies is Handheld Real-Time Spectrum Analyzer (RTSA) that operates from 9 kHz to 9.5 GHz. This spectrum analyzer operates in standard sweep, detection analysis/zero span, and real-time spectrum analysis mode. It implements an FFT engine on the built-in FPGA and support frame compression with trace detection while ensuring no missing samples between FFT frames. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2-port Vector Network Analyzer from 10 MHz to 44 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The S5243 from Copper Mountain Technologies is a 2-port Vector Network Analyzer that operates from 10 MHz to 44 GHz. It has an excellent dynamic range of 130 dB, typ. (10 Hz IF BW) and a fast measurement speed of 17 µs. The VNA can be used to measure all four S parameters (S11, S21, S12, and S22) and has an output power that can be adjusted from -50 dBm to 0 dBm. |
| |
Download Datasheet
Product Details | |
|
|
|
| PXI Vector Signal Transceiver from 380 MHz to 12 GHz | |
PXI RF Signal Transceiver
from Keysight Technologies
|
| The M9416A from Keysight Technologies is a PXI Vector Signal Transceiver that operates from 380 MHz to 6/8/12 GHz. It consists of a vector signal generator (VSG) and a vector signal analyzer (VSA) in a 4-slot PXIe module. This transceiver uses the N9065EM1E sequence analyzer measurement application to accelerate the measurement speed of the VSA. |
| |
Download Datasheet
Product Details | |
|
|
|
| Real-Time Peak USB Power Sensors from 50 MHz to 40 GHz | |
RF Power Meter & Sensor
from Boonton
|
| The RTP5000 Series of USB Power Sensors from Boonton are Real-Time peak power sensors that operate from 50 MHz to 40 GHz (available in 6 GHz, 18 GHz and 40 GHz configurations). They have a dynamic range from -60 dBm to +20 dBm with a measurement rate of 100,000 measurements per second, with no gaps in signal acquisition and zero measurement latency. |
| |
Download Datasheet
Product Details | |
|
|
|
| Ka-Band VSAT Manpack Terminal from 29.5-30 GHz (Tx) / 19.7-20.2 GHz (Rx) | |
SATCOM Terminal
from NETA Communications
|
| The MFA60PACK from NETA Communications is a VSAT Manpack Terminal that operates in the 29.5-30 GHz (Tx) and 19.2-20.2 GHz (Rx) frequency bands. It supports YAHSAT, AVANTI, and TURKSAT satellite services and is designed for easy installation with simple connections. This terminal delivers a gain of 41.6 dBi (Rx) and 45.1 dBi (Tx), with an operational elevation range of 5 to 80 degrees and continuous azimuth coverage. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
| Wi-Fi 6E & 7 Coexistence BAW Filter up to 6.8 GHz | |
Band Pass Filter
from Akoustis
|
| The A10168 from Akoustis is a Wi-Fi 6E & 7 Coexistence BAW Filter that operates up to 6.8 GHz, covering U-NII Bands from 7 and 8. It has a bandwidth of 600 MHz, provides a low insertion loss and meets the stringent rejection requirements, enabling coexistence with U-NII-1 thru 5. This BAW filter can handle the high-power levels required by the latest Wi-Fi 6E & 7 standards. |
| |
Download Datasheet
Product Details | |
|
|
|
| Multi-Tune High/Low Pass Filter from 750 to 1500 MHz | |
Tunable Filter
from Netcom
|
| The Model 5697 from Netcom is a Multi-Tune Switchable High/Low Pass Filter that operates from 750 to 1500 MHz. It has a highpass cutoff frequency range from 700 to 1250 MHz and a lowpass cutoff frequency range from 790 to 1500 MHz. This tunable fiter has a passband insertion loss of less than 3.5 dB and an out-of-band rejection of more than 15 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| 10 dB Directional Coupler from 0.4 to 18.50 GHz | |
Directional Coupler
from KRYTAR
|
| The 100418510 from KRYTAR is a Directional Coupler that operates from 0.4 to 18.5 GHz. This 10 dB coupler has a directivity of more than 12 dB and an insertion loss of less than 1.35 dB. It can handle an average power of 20 W and a peak power of 3 kW with a VSWR of 1.4:1. It is uniquely designed for system applications requiring external leveling, precise monitoring, signal mixing, swept transmission, and reception. |
| |
Download Datasheet
Product Details | |
|
|
|
| 50 W RF Termination from DC to 6 GHz | |
Termination
from MECA
|
| The 480-8 from MECA is an RF Termination that operates from DC to 6 GHz. It can handle an average power of 50 W, a peak power of 5 kW, and has a VSWR of 1.20:1. This 50-ohm termination is available in a connectorized module that measures 4.57(L) x 1.62 (Dia.) inches with SMA-female connector. |
| |
Download Datasheet
Product Details | |
|
|
|
| 5 W RF Termination from DC to 40 GHz | |
Termination
from JFW Industries
|
| The 50T-740 from JFW Industries is a RF Termination that operates from DC to 40 GHz. It can handle an average input power of 5 W and has a VSWR of less than 1.35:1. This 50 Ohm termination has a 2.92 mm connector. It can operate over a temperature range of -55 to 125 ºC. |
| |
Download Datasheet
Product Details | |
|
|
|
| 9.0 KW Solid State Power Amplifier from 1.0 to 2.0 GHz | |
RF Amplifier
from Advanced Amplifiers
|
| The AA-12G-8KWP from Advanced Amplifiers is a Solid State Power Amplifier that operates from 1.0 to 2.0 GHz. It delivers a peak pulse output power of 9.0 KW and a power gain of more than 69 dB. This class AB linear amplifier provides instantaneous L-Band octave bandwidth and has an input return loss of less than -10 dB. It has harmonics of less than -20 dBc and spurious of less than -60 dBc. |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by DigiKey | | Digi XBee® XR 900 | | The new Digi XBee® XR 900 module is a compact and reliable solution supporting deployment of long-range connectivity applications. The pre-certified module operates between 902 and 928 MHz in compliance with standards. Click here to learn more. | | | |
|
|
| 40 W Solid State Power Amplifier from 26.5 to 40 GHz | |
RF Amplifier
from Exodus Advanced Communications
|
| The AMP4066-LC from Exodus is a solid-state class AB high power amplifier that operates from 26.5 to 40 GHz. This amplifier provides a CW output power of 40 W with a power gain of over 46 dB. It has been designed for EMI/RFI, lab, and general communication applications. The amplifier can also be used for all single channel modulation standards. |
| |
Download Datasheet
Product Details | |
|
|
|
| Compact, Low Cost, Low Noise GPS/GNSS Disciplined Rubidium Oscillator | |
GPS/GNSS Disciplined Oscillator
from Safran Electronics & Defense
|
| The LNRClok-1500 from Safran is compact, smart, low cost, low noise GPS/GNSS-disciplined Rubidium oscillator (GPSDO) with an optional integrated GPS / GNSS receiver. This 10 MHz Disciplined Rubidium Oscillator delivers a sine wave output with a phase noise of -145 dBc/Hz at 1 kHz offset, has harmonics of less than -40 dBc and spurious levels of below -80 dBc. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Low Profile Wirewound Chip Inductors from 0.5 to 13 nH | |
RF Inductor
from Coilcraft
|
| The 0201HT Series from Coilcraft are Low Profile Wirewound Chip Inductors with inductance values from 0.5 to 13 nH. They have higher Q and lower DCR than similarly sized thin-film inductors and are optimized for high-frequency impedance matching in applications such as cell phones, wearable devices, Wi-Fi, Bluetooth, GPS, and LTE/5G IoT networks. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Integrated RF Front-End Module for 3G, 4G, and 5G Applications | |
Front End Module
from Skyworks Solutions
|
| The SKY58105-31 from Skyworks Solutions is a Front-End Module (FEM) that is designed for 3G, 4G, and 5G mobile devices. This module consists of separate 3G/4G/5G power amplifier (PA) blocks operating in mid-bands (MB) and high-bands (HB), a silicon controller with MIPI RFFE interface, RF-band switches, bidirectional couplers, MB/HB antenna switches, and integrated filters for bands 1, 3, 34, 39, 40, and 41. |
| |
Download Datasheet
Product Details | |
|
|
|
| 20 W GaN-on-SiC Power Amplifier MMIC from 6 to 18 GHz | |
RF Amplifier
from WAVEPIA Co,. Ltd.
|
| The WPGM0618020M from WAVEPIA is a GaN-on-SiC Power Amplifier MMIC that operates from 6 to 18 GHz. It delivers a saturated output power of 20.4 W (~43.1 dBm) with a small signal gain of 26.5 dB and has a power-added efficiency (PAE) of 19.4%. This PA is based on GaN-on-SiC technology and requires a DC supply from 28 to 32 V. It is available in a 10-lead bolt-down MPKG package that measures 16.94 x 7.35 x 1.40 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
| Broadband Power Amplifier from 2 to 8 GHz | |
RF Amplifier
from Quantic PMI (Planar Monolithics)
|
| The PMI-AFD4-020080-23P-SMA-2 from Quantic PMI (Planar Monolithics) is a Broadband Power Amplifier that operates from 2 to 8 GHz. It provides a gain of more than 32 dB with an input P1dB of -6 dBm and has a noise figure of less than 4.5 dB. This power amplifier requires a DC supply of 15 V and consumes less than 650 mA of current. It is available in a module that measures 1.83 x 0.76 x 0.20 inches and has SMA female connectors. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low Noise Amplifier from 1164 to 1610 MHz for GNSS Applications | |
RF Amplifier
from Nisshinbo Micro Devices Inc.
|
| The NT1193FAAE2S from Nisshinbo Micro Devices is a low-noise amplifier (LNA) designed for GNSS applications, covering the L1, L2, L5, and L6 bands from 1164 to 1610 MHz. It provides a gain of 21.5 dB with a noise figure of less than 1.1 dB and has a P1dB of -16 dBm. This LNA has an isolation of 30 dB between GNSS frequency bands and provides a return loss of 13 dB at the input and 16 dB at the output side. |
| |
Download Datasheet
Product Details | |
|
|
|
| High Gain e-pHEMT GaAs Low Noise Amplifier from 2 to 7 GHz | |
RF Amplifier
from BeRex, Inc.
|
| The BLB28 from BeRex is a High-Gain Low Noise Amplifier that operates from 2 to 7 GHz. It delivers 21.5 dB of gain with a noise figure of less than 1 dB and has an output P1dB of 19.6 dBm. This amplifier has an output IP3 of 31.5 dBm and an input return loss of 10 dB. It is based on a GaAs E-pHEMT process and is designed for applications requiring low noise and high gain. |
| |
Download Datasheet
Product Details | |
|
|
|
| D-Band Low Noise Amplifier from 110 to 170 GHz | |
RF Amplifier
from AT Microwave
|
| The AT-LNA-110170-3306 from AT Microwave is a Low Noise Amplifier that operates from 110 to 170 GHz. It provides 33 dB of gain with a noise figure of less than 8 dB and has a saturated output power of 0 dBm. This LNA is fabricated using InP-based MMIC technology, which ensures reliable and repeatable unit-to-unit results. It requires a DC supply of +5 V and consumes 70 mA of current. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2 W, GaN on SiC HEMT MMIC Power Amplifier from 17 to 20 GHz | |
RF Amplifier
from AmpliTech
|
| The AGMPA165215B from AmpliTech is a GaN HEMT Power Amplifier MMIC that operates from 17.3 to 20.2 GHz. It provides 20 dB of gain with a saturated output power of 35 dBm (~3.16 W) and has a PAE of 26 %. This GaN HEMT power amplifier requires a DC supply of +28 V and consumes 100 mA of current. It is available as a 50-ohm internally matched die that measures 2.4 x 1.8 x 0.1 mm. |
| |
Product Details | |
|
|
|
| 2.4 mm Male to 2.92 mm Female Coaxial Adapter from DC to 40 GHz | |
Between Series RF Adapter
from Marki Microwave
|
| The ADPMVFK from Marki Microwave is a 2.4 mm Male to 2.92 mm Female Coaxial Adapter that operates from DC to 40 GHz. It has an insertion loss of 0.1 dB, a VSWR of 1.02:1, and consumes less than 7.5 A of current. This straight-angled adapter measures (Dia) 8 x (L) 20.1 mm and has a passivated stainless-steel body with gold-plated contacts. |
| |
Download Datasheet
Product Details | |
|
|
|
| SMPM (Jack) Surface Mount PCB Connector from DC to 26.5 GHz | |
RF Connector
from Amphenol RF
|
| The 925-196J-51PT from Amphenol RF is an SMPM (Jack) PCB Connector that operates from DC to 26.5 GHz. It can withstand a dielectric voltage of more than 325 V (RMS) and has an insulation resistance of 1000 Mega ohms. This 50-ohm connector can handle an input power of up to 16 W and has a VSWR of less than 1.35:1. It has a gold-plated Brass body with an LCP insulator and a push-on mechanism withstanding over 500 mating cycles. |
| |
Download Datasheet
Product Details | |
|
