| Featured Products this Week . |
|
|
| 2-Port Compact USB VNA from 300 kHz to 1.3 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The TR1300/1 from Copper Mountain Technologies is a 2-Port lab-grade vector network analyzer that operates from 300 kHz to 1.3 GHz. This compact computer controlled VNA has a dynamic range of 130 dB and can measure up to 100,001 measurement points. It includes an RF measurement module and TR software application which runs on Windows or Linux operating system on a PC, laptop, tablet, or x86 board computer connecting to the measurement hardware via USB interface. |
| |
Download Datasheet
Product Details | |
|
|
|
| Thermal Vacuum Stable Cable Assemblies from DC to 40 GHz | |
RF Cable Assembly
from Maury Microwave
|
| The StabilityTVAC Series from Maury Microwave are Cable Assemblies that operate from DC to 40 GHz. These cable assemblies are thermally conditioned through aging and stabilization to relieve mechanical stress and ensure reliable performance over temperature. They utilize vented connectors that allow air to escape much faster, thereby empowering cable assemblies to stabilize with minimal delays and tests to be performed using rapid pressurization / depressurization cycles. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2 W, RF Isolator from 26.5 to 40 GHz | |
RF & Microwave Isolator
from MECA
|
| The IK-33.250 from MECA is an RF isolator that operates from 26.5 GHz to 40 GHz. It has an isolation of over 14 dB, insertion loss of 0.8 dB and a VSWR of below 1.50:1. The isolator can handle up to 2 watts of reflected power and up to 30 watts of peak power. It is available in a module with 2.92 mm female connectors. |
| |
Download Datasheet
Product Details | |
|
|
|
| GaAs Fixed Attenuator MMIC from DC to 50 GHz | |
Fixed Attenuator
from AmpliTech
|
| The AGATN03 from AmpliTech is a GaAs IPD Fixed Attenuator MMIC that operates from DC to 50 GHz. This 3 dB attenuator has an insertion loss of 2.96 dB and can handle an input power of up to +20 W with a return loss of 23 dB. It is available as a die that measures 1.00 x 0.75 x 0.1 mm with 50-ohm matched DC-coupled RF ports. |
| |
Download Datasheet
Product Details | |
|
|
|
| 300 W GaN Solid State Power Amplifier from 0.7 to 6.0 GHz | |
RF Amplifier
from Advanced Amplifiers
|
| The AA-700M6G-300 from Advanced Amplifiers is a GaN Solid State Power Amplifier that operates from 0.7 to 6.0 GHz. It delivers a saturated output power of 300 W and a power gain of over 53 dB with a power gain flatness of 4 dB p-p. This class AB linear amplifier has an input/output return loss of over 10 dB and a 2-tone intermodulation (IMD) of -30 dBc. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
| Featured e-Book | Download Now! | | |
|
|
| LTE Cat-6 Grade Cellular Module for APAC and EMEA Regions | |
Cellular Module
from Cavli Wireless
|
| The C120GS from Cavli Wireless is an LTE Cat-6 Grade Cellular Module. It is based on 3GPP Release 10 (upgradable to Release 11) and delivers a downlink data rate of 300 Mbps and an uplink data rate of 50 Mbps. This module is suitable for use in Asia-Pacific (APAC) and EMEA regions and allows developers to add high-performance LTE data bandwidth to space-constrained designs quickly. |
| |
Download Datasheet
Product Details | |
|
|
|
| Dual Mode Bluetooth 5.0 Module | |
RF Module
from Fujitsu
|
| The FWM7BTZ61 from Fujitsu is a Dual Mode Bluetooth 5.0 Module which is compatible with both Bluetooth low energy and Bluetooth classic BR/EDR modes. The symbol rate and data rate accommodate both 1 Mbps and improved 2 Mbps to facilitate communication speeds with other Bluetooth Low Energy devices. The classic mode supports a data rate of 1 Mbps (BR: basic rate) and 2 - 3 Mbps (EDR: Enhanced Data Rate) with output power up to 4 dBm. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Dual-Channel RF Front-End Module from 2.0 to 4.2 GHz | |
Front End Module
from Tagore Technology
|
| The TSL8329M from Tagore Technology is a Dual-Channel, Integrated Front-End Module that operates from 2.0 to 4.2 GHz. It has a cascading, two-stage Low Noise Amplifier (LNA) and a GaN based SPDT switch. In high gain mode, the cascaded two-stage LNA and switch have noise figure of 1 dB and provide gain of 32 dB at 3.6 GHz. |
| |
Download Datasheet
Product Details | |
|
|
|
| 60 GHz mm-Wave Short Data Link Transceiver for ISM Band Applications | |
RF Transceiver
from Analog Devices
|
| The ADMV9621 from Analog Devices is an mm-Wave Short Data Link Transceiver with a Tx frequency of 58.0125 GHz and Rx frequency of 63 GHz in the unlicensed industrial, scientific, and medical (ISM) band. It delivers a data rate of 100 Mbps with ultra-low latency and has a short link communication distance of 1-5 cm. This transceiver provides a Tx gain from -3 to +32 dB and an Rx gain from -10 to +69 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| 360-Degree Voltage Variable Phase Shifter from 10 to 16 MHz | |
Analog Phase Shifter
from Mini Circuits
|
| The SCPHS-13.6+ from Mini-Circuits is a 360-Degree Voltage Variable Phase Shifter that operates from 10 to 16 MHz. It provides a phase shift of 360 degrees and has an insertion loss of less than 2 dB. The phase shifter can handle an input power of up to 24 dBm and has a control voltage from 0-12 V. It is available in a surface-mount package that measures 0.87 x 0.80 x 0.25 mm and is ideal for Cellular, PCS, and DCS Applications. |
| |
Download Datasheet
Product Details | |
|
|
|
| 18 dB Cryogenic Isolator from 10 to 18 GHz | |
RF & Microwave Isolator
from Low Noise Factory
|
| The LNF-ISC10_18A from Low Noise Factory is a Cryogenic Isolator that operates from 10 to 18 GHz. It provides an isolation of 18 dB and has an insertion loss of 0.3 dB. This single-junction isolator can handle an input power of up to 1 W (~30 dBm) and operates at a temperature range from 0.01 K to 100 K. The LNF-ISC10_18A has been designed to meet the strict requirements of ultra-low temperature physics research and has a gold-plated OFHC copper body to which ensures minimum loss. |
| |
Download Datasheet
Product Details | |
|
|
|
| Radiation-Tolerant Transceiver 2025 to 2290 MHz for SATCOM Applications | |
SATCOM Transceiver
from Space Micro
|
| The NANOCOM from Space Micro is an S-Band Transceiver that operates from 2200 - 2290 MHz (Tx) and 2025 - 2100 MHz (Rx). It has a bandwidth of 50 MHz and supports BPSK, QPSK and OQPSK modulation schemes. This radiation-tolerant transceiver has been designed to perform in extreme environmental conditions. It has an on-board 50 MHz TCXO and a Xilinx Zynq System on a Chip (SoC). |
| |
Download Datasheet
Product Details | |
|
|
|
| Suspended Substrate High Pass Filter with 17.5 to 41 GHz Passband | |
RF High Pass Filter
from ERZIA
|
| The ERZ-HPF-1750-4100-2.0 from ERZIA is a High Pass RF Filter with a passband from 17.5 to 41.0 GHz. It has an insertion loss of less than 2 dB and a return loss of 13 dB. The filter is based on the Suspended Substrate (SS) technology that allows high selectivity with sharp edges within an optimized physical space. It can also be developed with lumped elements or microstrips for more complex RF filtering applications. |
| |
Download Datasheet
Product Details | |
|
|
|
| 450 MHz to 18.25 GHz Synthesizer with 10 MHz steps | |
Frequency Synthesizer
from Cobham Signal & Control Solutions
|
| The 435-36105 from Cobham is a Frequency Synthesizer that operates from 450 MHz to 18.25 GHz with 10 MHz steps. This device provides a switching speed of 250 µs from any start frequency to any stop frequency in the full range and has a parallel control interface to facilitate pipelined hopping. The spurious content is -55 dBc from 450 MHz to 12 GHz and -50 dBc from 12 to 18.25 GHz. |
| |
Download Datasheet
Product Details | |
|
|
|
| GaAs-Based I/Q Mixer from 2.5 to 15 GHz | |
RF Mixer
from Qorvo
|
| The QPX0002 from Qorvo is an I/Q Mixer with an RF/LO frequency from 2.5 to 15 GHz and an IF frequency from DC to 1 GHz. It provides an image rejection of 23 dB, an LO to RF isolation of 45 dB, and an LO to IF isolation of 25 dB. The MMIC mixer utilizes two double balanced mixer cells and a 90° internal hybrid. An external 90° IF hybrid is required to complete the image rejection or sideband suppression. |
| |
Download Datasheet
Product Details | |
|
|
|
| 10 MHz to 26.5 GHz USB Smart Noise Source | |
Noise Source
from Keysight Technologies
|
| The U1831C from Keysight is a USB-powered smart noise source designed to measure DUT noise figures up to 30 dB from 10 MHz to 26.5 GHz. The noise source has a low reflection coefficient and a nominal ENR value of 15 dB. The USB connection significantly reduces setup time and provides compatibility with noise figure analyzers and signal analyzers. |
| |
Download Datasheet
Product Details | |
|
|
|
| 2.4 mm Top-Launch Connector with Compression Contact | |
RF Connector
from Signal Microwave
|
| The TLF50 from Signal Microwave is a 2.40 mm Top-Launch Connector that operates up to 50 GHz. It transitions to a microstrip or grounded coplanar line on the top layer of the board. This connector has a compression contact and requires no soldering. The signal in this connector does not need to travel through the board vias and provides edge-launch-type performance anywhere on the board. |
| |
Download Datasheet
Product Details | |
|
|
|
| 100 W Quad-Band Multiplexer from 806 to 2165 MHz | |
Multiplexer
from G-WAY Microwave
|
| The CM848/931/1795/2045HK-D8 from G-WAY Microwave is a Quad Band Multiplexer for CELL/GSM900/DCS/UMTS Services applications. It has 4 channels with a passband for TDMA800 from 806 - 890 MHz, GSM900 passband from 902 - 960 MHz, GSM1800 passband from 1710 – 1880 MHz, and UMTS passband from 1935 -2165 MHz. |
| |
Download Datasheet
Product Details | |
|
|
|
| 71 to 76 MHz/81 to 86 MHz E-Band Diplexer | |
Diplexer
from ERAVANT
|
| The SWY-74384355-12-I1 from SAGE Millimeter is an E-band waveguide diplexer with a low passband from 71 to 76 GHz and high passband from 81 to 86 GHz. It has an isolation of more than 55 dB with an insertion loss of 0.5 dB and a channel rejection of 55 dB. The diplexer is available as a module that measures 2.83 x 0.75 x 0.39 inches with a WR-12 Waveguide interface. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low Noise Amplifier from 1164 to 1610 MHz for GNSS Applications | |
RF Amplifier
from Nisshinbo Micro Devices Inc.
|
| The NT1193FAAE2S from Nisshinbo Micro Devices is a low-noise amplifier (LNA) designed for GNSS applications, covering the L1, L2, L5, and L6 bands from 1164 to 1610 MHz. It provides a gain of 21.5 dB with a noise figure of less than 1.1 dB and has a P1dB of -16 dBm. This LNA has an isolation of 30 dB between GNSS frequency bands and provides a return loss of 13 dB at the input and 16 dB at the output side. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| Ruggedized Ground Data Terminal from 14.4 to 15.35 GHz | |
SATCOM Terminal
from Cubic
|
| The Mantis II from Cubic is a Ground Data Terminal that operates from 14.4 to 15.35 GHz. It supports long-range, high-data-rate communications with airborne platforms equipped with a multitude of DoD standard Common Data Link (CDL) waveforms. This terminal provides an operating range of up to 250 nmi or more (depending on system configuration) and delivers a full-duplex data rate from 200 Kbps to 44.73 Mbps. |
| |
Download Datasheet
Product Details | |
|
|
|
| IP67-Rated Compact RFID Antenna from 865 to 928 MHz | |
RFID Antenna
from Zebra
|
| The AN720 from Zebra is an RFID Antenna that operates from 865-868 MHz and 902-928 MHz. This left-hand circularly-polarized (LHCP) antenna provides a gain of 3 dBiL and has a front-to-back ratio of 8 dB. It has a 3 dB beamwidth of 100° (in both planes) and can handle an input power of up to 10 W. This antenna offers the versatility and performance required to meet environmental and application needs in customer-facing areas, warehouses, and outdoor environments. |
| |
Download Datasheet
Product Details | |
|
|
|
| Cross-Polarized 4-Port Base Station Antenna from 698 to 3980 MHz | |
Base Station Antenna
from JMA Wireless
|
| The MX04FFP665-01 from JMA Wireless is a 4-Port Base Station Antenna that operates from 698 to 3980 MHz. This ±45° antenna provides a gain of up to 18 dBi and has a VSWR of less than 1.5:1. It has a horizontal beamwidth of 65°, a vertical beamwidth of 5.4° to 20° and supports electrical downtilt from 0 to 14°. This antenna has fully integrated (iRETs) with independent RET control for low-band, mid-band, and CBRS/C-Band. |
| |
Download Datasheet
Product Details | |
|
