PREV 19 Aug, 2020 NEXT

New RF and Microwave Products this Week

19 Aug, 2020 - everything RF Newsletter

New products this week. View it in your browser

 
Date: 19 Aug, 2020
 
Sponsored by Skyworks
 
 
 
New RF and Microwave Products this Week
Front End Module
Dual-Channel GaN MMIC Front-End Module from 37 to 40.5 GHz

Front End Module  from Qorvo

The QPF4005 from Qorvo is a Dual-Channel GaN MMIC Front-End Module (FEM) that operates from 37 to 40.5 GHz. The Tx path (PA+T/R SW) provides a saturated output power of 2 W for each channel with a small signal gain of 18 dB while the Rx path (LNA+T/R SW) is designed to provide 15 dB of gain with a noise figure of less than 4.5 dB.
Download Datasheet | Product Details
RF Transceiver
E-Band Transceiver for LTE, 5G, and Mobile Backhaul Networks

RF Transceiver  from Filtronic

The Hercules transceiver from Filtronic is a turn-key solution for ultra-high power high capacity E-band links, combining Filtronic’s Orpheus (Transceiver) and Cerus (HPA) modules. The transceiver operates from 71 to 76 GHz / 81 to 86 GHz and supports up to 2 GHz RF channels and 256 QAM modulation.
Download Datasheet | Product Details
Down Converter
Down Converter from 2 to 18 GHz for Military Applications

Down Converter  from Norden Millimeter

The NDC0218I0102N10 from Norden Millimeter is a Down Converter that down-converts an input RF frequency from 2 to 18 GHz to output IF frequency from 1.375 to 2.375 GHz. It delivers a P1dB of up to 11 dBm with a conversion gain of over 10 dB and has a noise figure of 10 dB. The device can provide 56 dB of variable attenuation and has a channel bandwidth flatness of +/- 2 dB.
Download Datasheet | Product Details
RF Amplifier
37 to 40 GHz Low Noise Amplifier for 5G Applications

RF Amplifier  from Altum RF

The ARF1203Q2 from Altum RF is a Low Noise Amplifier that operates from 37 to 40 GHz. It provides a linear gain of 20.5 dB with a noise figure of 4 dB and has a P1dB of 13 dBm. It is well suited for demanding, high-order modulation schemes such as millimeter-wave 5G. The amplifier draws 40 mA of current from a 3.3 V DC supply.
Download Datasheet | Product Details
180 Degree Hybrid Coupler
180° Hybrid Coupler from 1 to 2 GHz

180 Degree Hybrid Coupler  from UMCC

The HC-C000-MN from UMCC is a 180° Hybrid Coupler that operates from 1 to 2 GHz. It has a coupling factor of 3.4 dB and provides an isolation of more than 22 dB. The device can handle up to 50 W of average and 3 kW of peak input power. It is available in a module that measures 90.9 x 40.6 x 17.5 mm with N-type female connectors.
Download Datasheet | Product Details
XO
Ultra-Low Jitter Differential XO from 25 to 644 MHz

XO  from SiTime

The SiT9501 from SiTime is an ultra-low jitter Differential MEMS Oscillator with 14 standard networking output frequencies from 25 MHz to 644.53125 MHz. It has frequency stability of up to ±20 ppm over an operating temperature range from -40 to +105 °C and LVPECL, LVDS, HCSL, Low-power HCSL, and FlexSwing signaling options.
Download Datasheet | Product Details
OCXO
10 MHz Double Oven Ultra-Precision OCXO

OCXO  from Dynamic Engineers

The DOCXO5050AN-10MHz from Dynamic Engineers is a Double Oven Ultra Precision OCXO with an operational frequency of 10 MHz and frequency stability of up to ±1x10-11 ppb. It provides a sinewave output and has a phase noise of -155 dBc at 1 kHz offset. The device requires a 5/12 V of supply voltage while consuming up to 800 mA of current and has a warm-up time of less than 15 minutes.
Download Datasheet | Product Details
Sponsored by Skyworks
Skyworks
High Linearity PIN Limiter Module for Cellular Infrastructure, 5G and Wi-Fi Applications
The SKY16603-632LF is an integrated limiter module for use as a passive receiver protector in systems up to 6 GHz in an ultra-compact package. This device is ideal for applications including base stations, WLNA, 5G massive MIMO infrastructure, and test instrumentation. Click here to learn more.
 
Power Sensor
True-RMS Power Sensor from 1 MHz to 44 GHz

Power Sensor  from LadyBug Technologies

The LB5944A from LadyBug Technologies is a True-RMS Power Sensor that operates from 1 MHz to 44 GHz for general-purpose average power or True RMS and scalar measurements. The sensor has an exceptionally fast measurement speed, a broad dynamic range (-60 to +26 dBm), and a wide set of options for programmatic and embedded applications in the industry.
Download Datasheet | Product Details
Microwave Generator
100 W GaN Microwave Generator from 2400 to 2500 MHz

Microwave Generator  from RFHIC

The RIM25100-20G from RFHIC is a GaN Microwave Generator that operates from 2400 to 2500 MHz. It delivers up to 100 W of CW output power with an efficiency of more than 58%. The device can be used to generate CW, linear, and pulsed signals with a pulse duty cycle from 1 to 99%. It has a frequency stability of ±2.5 ppm and has an integrated phase-locked loop.
Download Datasheet | Product Details
RF Shielded Test Enclosure
mm-Wave Shielded Test Enclosure from 24 to 40 GHz

RF Shielded Test Enclosure  from Taiwan Rapidtek Inc.

The RP-H40A3SA-NBC01 from Taiwan Rapidtek Inc. is an RF Shielded Test Enclosure that operates from 24 to 40 GHz. The enclosure has an absorbing foam that provides over 75 dB of isolation. It measures 1130 (W) x 780 (D) x 915 (H) mm from inside and is available with 2.92 mm connectors and RJ45 x 4, RS232 x 2, USB 3.0 x 4 and type C x 2 control interfaces. The enclosure has a pneumatic lid.
Download Datasheet | Product Details
Antenna/OTA Test System
mm-Wave Mini-Chamber for OTA Measurements

Antenna/OTA Test System  from Milliwave Silicon Solutions

The MBX33 from Milliwave Silicon Solutions is a mmWave Mini-Chamber that fits on an 8-foot lab bench. Compared to the standard MilliBox line, the MBX33 is composed of 30 Inch cubes to allow for more space inside the chamber. It has 3 instrument bays to place a spectrum analyzer or vector network analyzer on one side and a signal generator or baseband board on the other side below the measurement deck.
Download Datasheet | Product Details
RF Amplifier
1000 W Solid-State Power Amplifier from 10 kHz to 400 MHz

RF Amplifier  from AR RF/Microwave Instrumentation

The 1000A400 from AR RF/Microwave Instrumentation is a Solid-State Power Amplifier that operates from 10 kHz to 400 MHz. This self-contained, air-cooled amplifier, when used with an RF sweep generator, provides more than 1000 watts of power with a gain of over 60 dB. It has a Digital Control Panel (DCP) from where the gain and power level can be controlled.
Download Datasheet | Product Details
Vector Network Analyzer
Multiport Network Analysis Solution for MIMO and 5G Applications

Vector Network Analyzer  from Copper Mountain Technologies

The RNVNA from Copper Mountain Technologies is a customizable Multiport Network Analysis Solution for MIMO antennas and other 5G applications. It has been built using CMT 1-Port USB vector network analyzers and operates over a frequency from 1 MHz to 18 GHz. The solution links up to 16 analyzers together to form a multiport network analysis system, allowing users to measure vector reflection and scalar transmission parameters.
Download Datasheet | Product Details
RF Spectrum Analyzer
Compact USB Real-Time Spectrum Analyzer from 10 MHz to 6 GHz

RF Spectrum Analyzer  from Aaronia AG

The SPECTRAN V6 X from Aaronia is a high-performance USB real-time spectrum analyzer that operates from 10 MHz to 6 GHz. The analyzer supports dual USB True I/Q streaming of up to 245 MHz (IQ rate) real-time bandwidth. Multiple devices can be cascaded together to achieve an even higher real-time bandwidth.
Download Datasheet | Product Details
Sponsored by Skyworks
 
 
 
Antenna
2.4/5.0 GHz Dual Band WiFi Waterproof Antenna

Antenna  from 2J Antennas

The 2J0502-C115N from 2J Antennas is a Dual Band WiFi / ISM Band Antenna that operates from 2410 to 2490 and 4920 to 5925 MHz. It is linearly polarized and delivers a peak gain of over 2.4 dBi with an efficiency of up to 53.1% and can handle 25 W of input power. This RoHS-compliant and IP67-rated connector mount antenna has an omnidirectional radiation pattern and a VSWR of less than 2.6:1.
Download Datasheet | Product Details
GNSS Simulator
GNSS Simulator for Aviation, Maritime and Other Navigation Applications

GNSS Simulator  from WORK Microwave

The Xidus-6HU from Work Microwave is a GNSS Simulator that supports GPS L1/L2/L5, Galileo E1/E5/E6, GLONASS L1/L2, and BeiDou B1I/B2I/B3 bands. It is fully capable of multi-constellation, multi-frequency simulations for a wide range of test scenarios used in research and development of GNSS receivers, including aviation, maritime, and other navigation applications.
Download Datasheet | Product Details
Tower Mount Amplifier
Twin Tower Mount Amplifier with AISG 2.0 Protocol

Tower Mount Amplifier  from CommScope

The E14R00P05 from Commscope is a Twin Tower Mount Amplifier that operates from 2500 to 2570 MHz (Uplink – Rx) and 2620 to 2690 MHz (Downlink – Tx). On the Rx side, it provides a gain of 12 dB with a noise figure of less than 1.6 dB. On the Tx side, it can handle an RMS power of up to 200 Watts and has an insertion loss of 0.8 dB.
Download Datasheet | Product Details
Diplexer
High Power RF Diplexer from 600 - 960 / 1695 - 2690 MHz

Diplexer  from Innowave RF

The 903C-829-2205 from Innowave RF is a Diplexer that operates from 600 to 960 MHz and 1695 to 2690 MHz. It has an insertion loss of 0.20 dB, provides isolation of more than 40 dB, and has a PIM of -161 dBc. The diplexer can handle up to 100 W of average power and 250 W of peak input power.
Download Datasheet | Product Details
GNSS Module
GNSS Module for GPS, GLONASS, BDS and Galileo Constellations

GNSS Module  from ALPS ALPINE

The UMSZ2 from Alps Alpine is a GNSS Module for GPS, GLONASS, BDS, and Galileo constellations. This module has a navigation sensitivity of -147 dBm and tracking sensitivity of -160 dBm. It requires a supply of 3.3 V and is designed to operate over a wide temperature range. The module supports the UART interface and is available in an SMT package that measures 25 × 20 × 2.6 mm.
Download Datasheet | Product Details
Laminate
Low-Loss Laminate Material for Aerospace & Defense Applications

Laminate  from Isola Group

The IS680 AG from Isola is a Low-Loss Laminate Material suitable for many commercial RF/microwave printed circuit designs. This substrate has a dielectric constant (Dk) from 3 to 3.48 which is stable while operating from -55°C to +125°C up to W-band frequencies. The laminates are offered with different thickness options - 20, 30, 60 mils (0.51, 0.76, 1.5 mm).
Download Datasheet | Product Details
90 Degree Hybrid Coupler
90-degree Hybrid Coupler from 1 to 4 GHz

90 Degree Hybrid Coupler  from VidaRF

The VHC1040A from VidaRF is a 90-degree Hybrid Coupler that operates from 1 to 4 GHz. The device has an insertion loss of 0.6 dB and an isolation of 22 dB. It has an amplitude balance of ±0.50 dB and a phase balance of ±5 degrees. This coupler can handle an input power of 50 watts and has a VSWR of 1.25:1. It is available in a module with connectors.
Download Datasheet | Product Details
Termination
Low PIM Terminations from 380 MHz to 2700 MHz

Termination  from MECA

The Low PIM Terminations from MECA operate from 380 MHz to 2.7 GHz. They can handle up to 250 Watts of power - available in 10 W, 30 W, 50 W, 100 W and 250 W models. The terminations have a low PIM of -160 dBc to -165 dBc. They are available with multiple connector configurations - Type N and 4.1/9.5, 4.3/10.0 and 7/16 DIN connectors.
Download Datasheet | Product Details
Antenna
2.4 GHz Hinged External Antenna for Wi-Fi/Bluetooth

Antenna  from MOLEX

The 2144150001 from Molex is a Wi-Fi/Bluetooth Hinged External Antenna that operates from 2.4 to 2.5 GHz. This linearly polarised antenna delivers a gain of 5.3 dBi with an efficiency of over 80% and can handle 2 W of RF power. The joint hinge of the antenna allows 90° rotation on a vertical plane, and the SMA (M) connector allows 180° rotation on a horizontal plane.
Download Datasheet | Product Details
Power Divider
2 Way Wilkinson Power Divider from 380 to 2700 MHz

Power Divider  from Huber+Suhner

The 5501.17.0027 from HUBER+SUHNER is a 2 Way Wilkinson Power Divider that operates from 380 to 2700 MHz. It can handle up to 10 W of power, has an insertion loss of 0.8 dB, and provides isolation of 20 dB. It is available with N-Type female connectors and measures 19.6 x 87 x 102 mm. The splitter is ideal for multiband antennas and leaky cable systems applications.
Download Datasheet | Product Details
About everything RF
everything RF keeps users up to date with the RF & Microwave Industry. We provide users with the latest industry news, information on new product releases, upcoming events, articles, white papers, interviews and much more.
To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]