1. everything RF
  2. RF Newsletters
more
PREV 31 Aug, 2020 NEXT

Latest News & White Papers this Week

31 Aug, 2020 - everything RF Newsletter

Top stories this week. View it in your browser

 
Date: 31 Aug, 2020
 
Sponsored by Keysight Technologies
 
 
 
Latest News this Week
More than 8000 Participants Attend the First Virtual IMS Event - IEEE MTT-S
New Microwave and mm-Wave Filter Assemblies for Demanding Space Applications - Cobham Advanced Electronic Solutions
TrellisWare to Develop Troposcatter Communications Systems for the US Navy - TrellisWare Technologies
Remcom Updates its EM Simulation Software to Better Support mm-Wave Antenna Design - Remcom
Akoustis Introduces the First 6.5 GHz XBAW Filter for Wi-Fi 6E Applications - Akoustis
RF Based Microneedling Technology Helps Reverse Skin Aging - Cutera
Avnet Introduces Cost-Effective LTE Development Kit for IoT Applications - Avnet
Vayyar Introduces High Resolution Short Range Imaging Radar for ADAS & Autonomous Vehicles - Vayyar
Survey Reveals True Cost of Delays Caused by Test Equipment Misconfiguration, Maintenance and Training Issues - Keysight Technologies
Resonant Develops 5G Filters Using SAW Technology - Resonant Inc
Kymeta Raises $85 Million in Funding from Bill Gates to Accelerate Growth - Kymeta Corporation,
Qorvo’s RF & Microwave Die Products Now Available from Richardson Electronics - Qorvo
Hitachi Chemical Announces Mass Production of Laminate Material for 5G Applications - Hitachi Chemical
More News
Interesting White Papers & Articles
Testing Challenges and Solutions for Accurate Wi-Fi 6 Chipset and Device Characterization - Boonton
Active Load-Pull System in Doherty Power Amplifier - FOCUS MICROWAVES GROUP
Amplifier Measurements with a VNA - Copper Mountain Technologies
RFID Applications Keep Expanding - Mouser Electronics
Fast Fourier Transforms Explained - Pico Technology
More White Papers
Sponsored by Keysight Technologies
Keysight Technologies
Master Network Analysis Fundamentals
Network Analysis fundamentals covers transmission line basics, S-Parameters, and the Smith Chart. Transmit, receive and directivity paths will be described along with how dynamic range and accuracy can be optimized. Watch Webinar Now.
 
Upcoming Event
Event Image
Military Space Situational Awareness 2020
Date: 3 and 4 September, 2020
Location: Virtual Event
More Events
Featured Products this Week
RF Amplifier
2500 W Solid-State Amplifier from 10 kHz to 225 MHz

RF Amplifier  from AR RF/Microwave Instrumentation

The 2500A225B from AR RF/Microwave Instrumentation is a Solid-State Amplifier that operates from 10 kHz to 225 MHz. This self-contained, air-cooled amplifier, when used with a sweep generator, delivers more than 2500 W of output power with a gain of over 64 dB and has a noise figure of 7 dB. It has a typical spurious level of -70 dBc and harmonic distortion of -30 dBc.
Download Datasheet | Product Details
RF Switch
High-Speed Non-Reflective PIN Diode SPST Switch from 0.2 to 18 GHz

RF Switch  from KRATOS General Microwave

The F192A from Kratos is a Non-Reflective PIN Diode SPST Switch that operates from 0.2 to 18 GHz. This high-speed switch has an insertion loss of less than 3.5 dB with an isolation of over 70 dB. It can handle up to 500 mW of peak power and requires a DC supply of -12 / 5 V. The switch has an integrated driver circuit which is controlled by an external logic TTL signal.
Download Datasheet | Product Details
DRO
Dielectric Resonator Oscillators from 0.5 to 24 GHz

DRO  from Amplus Communication

The AM-4200 Series from Amplus is Dielectric Resonator Oscillators that operate from 0.5 to 24 GHz. They deliver an output power of up to +12 dBm and have a frequency stability of 5 ppm/°C. The oscillators have a phase noise of up to -118 dBc/Hz at a 100 kHz offset and spurious of less than -80 dBc. They are designed using low noise solid-state transistors and high-Q dielectric or coaxial resonators.
Download Datasheet | Product Details
Vector Network Analyzer
1-Port USB Vector Network Analyzer from 1 MHz to 6 GHz

Vector Network Analyzer  from Copper Mountain Technologies

The R60 is a single port USB-powered VNA (Reflectometer) capable of measuring S11 from 1 MHz to 6.0 GHz. It can be operated from any Windows PC or laptop using a USB cable. The R60 provides a wide variety of analysis capabilities, including S11, time-domain with gating, DTF measurements, and much more.
Download Datasheet | Product Details
Automotive Radar Chipset
24 GHz Transmitter MMIC for Automotive Applications

Automotive Radar Chipset  from Infineon Technologies

The BGT24AT2 from Infineon Technologies is a 24 GHz Transmitter MMIC with 2 transmitter outputs and one LO output. This multifunction signal source accommodates a 24 GHz fundamental voltage controlled oscillator and a frequency divider with a division ratio of 1024. The frequency divider output is differential.
Download Datasheet | Product Details
Cellular IoT Module
LPWA Module for LTE-M / NB-IoT with 2G Fallback

Cellular IoT Module  from Sierra Wireless

The AirPrime WP7702 from Sierra Wireless is an LPWA Module that offers LTE-M / NB-IoT connectivity with 2G fallback for any cellular network. This module for Cat-M1/NB1 worldwide networks is fully compliant with the 3GPP Release 13 standard, providing a new low-cost, low-power technology for low-bandwidth IoT applications with an extended reach beyond traditional cellular applications.
Download Datasheet | Product Details
Wireless Charging Transmitter
Highly Integrated WattUp Wireless Power Transmitter

Wireless Charging Transmitter  from Dialog Semiconductor

The DA4100 from Dialog Semiconductor is a highly integrated RF transmitter System-on-Chip designed to provide optimal wireless charging of WattUp receiver devices. It consists of the RF transmitter, power management, and integrated DC-DC to power Dialog’s external Bluetooth® Low Energy ICs, delivering a complete WattUp transmitter system solution.
Download Datasheet | Product Details
Sponsored by Keysight Technologies
 
 
 
RF Cable
Probe Station Test Cables that Operate up to 110 GHz

RF Cable  from MegaPhase

The PS Series from MegaPhase are Probe Station Test Cables that operate up to 110 GHz. These test cables are specifically designed for dynamic high-frequency probe station measurements and offer phase stable performance with low losses. The PS Series of cables can be mechanically formed to ensure proper connector to connector spacing.
Download Datasheet | Product Details
Front End Module
5 GHz Front-End Module for Wi-Fi 6 Routers and Gateway Applications

Front End Module  from Skyworks Solutions

The SKY85750-11 from Skyworks is 5 GHz WLAN Front End Module for 802.11ax Applications. The module consists of a Low Noise Amplifier with bypass, SPDT Tx/Rx switch, a digital pre-distortion (DPD) coupler and a Power Amplifier with an integrated logarithmic power detector to provide a closed-loop power control system.
Download Datasheet | Product Details
Microwave Generator
200 W GaN Microwave Generator from 2400 to 2500 MHz

Microwave Generator  from RFHIC

The RIM25200-20G from RFHIC is a GaN Microwave Generator that operates from 2400 to 2500 MHz. It delivers a typical CW output power of 200 W with an efficiency of up to 60%. The amplifier has a pulse duty cycle from 1 to 99% and a frequency resolution of 100 kHz. It requires a supply voltage of 50 V and consumes more than 6.88 A of current.
Download Datasheet | Product Details
Termination
150 W Thin-Film Resistive Terminations from DC to 18 GHz

Termination  from AVX Corporation

The RP8 Series from AVX Corporation are Thin Film Chip Terminations that operate from DC to 18 GHz. These 50-ohm terminations have resistance from 10 to 200 Ohms and can handle up to 150 watts of power. They have a VSWR of less than 1.25:1 and a temperature coefficient of under ±150 ppm/ºC. The RP8 Series terminations are based on an Aluminum Nitride substrate material with silver-plated terminals.
Download Datasheet | Product Details
Frequency Synthesizer
0.010 to 15 GHz RF Frequency Synthesizers

Frequency Synthesizer  from L3Harris Narda-MITEQ

The SLS2 Series from L3 Narda-MITEQ are frequency synthesizers that operate from 0.01 to 15 GHz with a standard step size of 1 kHz. The synthesizers provide an output power of up to 13 dBm and a spurious suppression of 60 dBc. They require a supply voltage from 7 to 28 V DC and consume less than 4 watts of power.
Download Datasheet | Product Details
180 Degree Hybrid Coupler
180° Hybrid Coupler from 1 to 18 GHz for EW and SATCOM Applications

180 Degree Hybrid Coupler  from KRYTAR

The 4010180 from Krytar is a 180 Degree Hybrid Coupler that operates from 1 to 18 GHz. This 3 dB coupler can handle up to 20 watts of average power and up to 3 kW of peak power. It has an insertion loss of less than 2.9 dB and provides isolation of over 15 dB across the band. This device has an amplitude balance of ± 0.60 dB and a phase balance of ± 12 degrees.
Download Datasheet | Product Details
RF Mixer
I/Q Double-Balanced Mixer from 4 to 8.5 GHz

RF Mixer  from Fairview Microwave

The FMMX9000 from Fairview Microwave is an I/Q Double-Balanced Mixer with an RF frequency range from 4 to 8.5 GHz and an IF frequency range from DC to 3.5 GHz. It has a low conversion loss of 7.5 dB, LO to RF isolation of 40 dB, and LO to IF isolation of 20 dB. The mixer can handle up to 20 dBm of input power and has a high image rejection of over 35 dB.
Download Datasheet | Product Details
OCXO
10 MHz OCXO with GPS Jamming Protection

OCXO  from IQD Frequency Products

The IQCM-300 from IQD Frequency Products is an OCXO with an operational frequency of 10 MHz. It provides an HCMOS output waveform and has a rise/fall time of less than 8 ns with a duty cycle of 55%. The oscillator can operate over a temperature range from -20 to 75 °C and has a phase noise of -150 dBm/Hz at a 1 MHz offset. It requires a supply voltage of 5V.
Download Datasheet | Product Details
Band Pass Filter
LC Bandpass Filter with Passband from 5950 to 6850 MHz

Band Pass Filter  from MCV Microwave

The BPL6400-900A1 from MCV Microwave is an LC Bandpass Filter with a passband from 5950 to 6850 MHz and a center frequency at 6400 MHz. It has an insertion loss of less than 3 dB in the passband and provides up to 55 dB of attenuation above and below it. The filter has a VSWR of less than 1.8:1 and can handle up to 1 W of input power.
Download Datasheet | Product Details
Waveguide Isolator
U-band Waveguide Isolator from 43 to 46 GHz

Waveguide Isolator  from Renaissance Electronics Corporation

The 2WR22NB from Renaissance Electronics is a U-band Waveguide Isolator that operates from 43 to 46 GHz. It has a low insertion loss of 0.5 dB, isolation of 18 dB, and a VSWR of 1.30:1. The device can handle up to 0.5 Watts of power and has low system level distortion/noise generations. It is available in a compact module with a WR22 waveguide interface.
Download Datasheet | Product Details
RF Spectrum Analyzer
Handheld Spectrum Analyzers from 10 MHz to 3.6/6 GHz

RF Spectrum Analyzer  from Aim-TTi

The PSA Series 5 from Aim-TTi are Portable RF Spectrum Analyzers that operate from 10 MHz to 3.6/6 GHz. These handheld analyzers have a resolution bandwidth from 300 Hz to 10 MHz and have a typical noise floor of less than -120 dBm at a -40 dBm ref. level and 10 kHz RBW (better than -160 dBm per Hz). The analyzers have a zero span mode with AM and FM audio demodulation.
Download Datasheet | Product Details
Base Station Antenna
Dual-Polarized Sector Antenna from 4.9 to 5.9 GHz

Base Station Antenna  from Cobham Antenna Systems

The SA17-60-5.4VH/9520 from Cobham Antenna Systems is a Dual-Polarized Sector Antenna that operates from 4.9 to 5.9 GHz. This antenna delivers a gain of 17 dBi and can handle 50 W of power. It has a VSWR of less than 2:1 and a front to back ratio of over 25 dB. The unit provides a 60-degree coverage and can be electrically tilted by 2 degrees.
Download Datasheet | Product Details
RFID Tag
UHF Band RFID Vehicle Hang Tag

RFID Tag  from GAO RFID

The 116052 from GAO RFID is an RFID Vehicle Hang Tag that operates from 860 to 960 MHz. This tag supports ISO/IEC 18000-6C EPC Class 1 Gen 2 RF protocols and has a read range of over 5 meters (18 feet). It is encapsulated in rigid polyester and can be subsurface printed in various designs with a logo and bar code and other key information.
Download Datasheet | Product Details
RFID Antenna
UHF RFID Antenna from 902 to 928 MHz

RFID Antenna  from Abracon LLC

The ARRKP4065-S915A from Abracon is a UHF RFID Antenna that operates from 902 to 928 MHz. This right hand circularly polarized antenna delivers a gain of 1.5 dBi and has a VSWR of less than 2:1. The antenna has a bandwidth of more than 6 MHz and a low axial ratio of 3:1. It is available in a dielectric ceramic module that measures 35 x 35 x 4 mm with a 4-inch cable and an IPEX connector.
Download Datasheet | Product Details
About everything RF
everything RF the leading website for the RF & Microwave Industry. We provide the latest news, information on new product releases, white papers, articles, interviews, calculators and much more.
To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]