PREV 25 Nov, 2020 NEXT

New RF and Microwave Products this Week

25 Nov, 2020 - everything RF Newsletter

New products this week. View it in your browser

 
Date: 25 Nov, 2020
 
Sponsored by CRFS
 
 
 
New RF & Microwave Products this Week
Switch Matrix
8 x 8 Butler Matrix from 2.4 to 8 GHz

Switch Matrix  from Ranatec

The RI 3101 from Ranatec is an 8 x 8 Butler Matrix that operates from 2.4 to 8 GHz. It has been designed to support Bluetooth and Wi-Fi bands, including the extended Wi-Fi frequency band up to 7.125 GHz. This butler matrix can be used for antenna array beamforming and interference testing for multiple systems within the frequency range and for multichannel multipath emulation.
Download Datasheet | Product Details
RF Switch
SP4T Micro-Mechanical RF Switch from DC to 26 GHz

RF Switch  from Menlo Micro

The MM5130 from Menlo Micro provides ultra-low loss operation and excellent RF performance from DC to 26 GHz, with an IP3 surpassing 95 dBm, and greater than 3 billion switching cycles at +85ºC. This MEMS switch is an ideal solution for replacing large RF electromechanical relays, as well as RF/microwave solid-state switches in applications where linearity and insertion loss are critical parameters.
Download Datasheet | Product Details
Frequency Multiplier
GaAs MMIC mm-Wave 4x Multiplier from 40 to 125 GHz

Frequency Multiplier  from Marki Microwave

The MMQ-40125H from Marki Microwave is a GaAs MMIC Millimeter Wave 4x Multiplier that multiplies an input frequency from 10 - 31.25 GHz to an output frequency from 40 - 125 GHz. This Schottky diode multiplier consumes no DC power, offers excellent harmonic rejection, and provides very flat output power across an extremely wide output range.
Download Datasheet | Product Details
RF Switch
100 W SPDT Tx/Rx Switch from 10 to 2000 MHz

RF Switch  from AMCOM Communications, Inc.

The AM002050S2-0H from Amcom Communications is a High-Power SPDT Tx/Rx Switch that operates from 10 to 2000 MHz. It has an insertion loss of 0.8 dB with an isolation of more than 50 dB between the Tx / Rx port and a switching speed of less than 10 microseconds. This switch can handle up to 100 W (50 dBm) of CW power. It requires a DC supply of +28V and supports TTL control logic to switch between ports.
Download Datasheet | Product Details
RF Test Set
5G Portable Base Station Analyzer for Multi-Carrier Cellular Signals

RF Test Set  from Viavi Solutions

The CellAdvisor 5G from Viavi Solutions is a 5G Portable Base Station Analyzer that is capable of testing and trouble-shooting concurrent multi-technology and multi-carrier cellular signals. It is designed for 4G and 5G radio access networks and performs signal analysis tests for stand-alone LTE or 5G technologies. It performs quick and reliable concurrent FR1 (sub-6 GHz) and FR2 (mm-wave) signal analysis by eliminating the need to rapidly switch between these dual ports.
Download Datasheet | Product Details
Vector Network Analyzer
2-Port Vector Network Analyzer from 9 kHz to 4.5 GHz

Vector Network Analyzer  from Copper Mountain Technologies

The S5045 from Copper Mountain Technologies is a 2-Port Vector Network Analyzer that operates from 9 kHz to 4.5 GHz. It has a dynamic range of 130 dB (10 Hz IF BW) and can be used to measure all four S parameters (S11, S21, S12, and S22). The output power of this VNA can be adjusted from -55 dBm to 5 dBm and has a measurement speed of 70 µs.
Download Datasheet | Product Details
RF Amplifier
38.2 dBm GaN Power Amplifier from 2 to 18 GHz

RF Amplifier  from Northrop Grumman

The APN267 from Northrop Grumman is a GaN HEMT Power Amplifier that operates from 2 to 18 GHz. It provides a saturated output power of 38.2 dBm with a gain of over 11 dB and Power Added Efficiency of 33%. This amplifier requires a DC supply of 24 V and consumes 480 mA of current. It is fabricated on a GaN on SiC process and is available as a die that measures 12.32 sq. mm.
Download Datasheet | Product Details
Sponsored by CRFS
CRFS
SenS Portable - full rate I/Q recording in a portable package
SenS Portable is a lightweight, high-resolution RF recorder that can stream full-rate I/Q data to built-in 25TB storage. With a frequency range of up to 18GHz and a 100MHz IBW, the high fidelity SenS Portable ensures you’ll never miss a signal. Click here to learn more.
 
RF Amplifier
5 kW GaN Solid-State Transmitter from 9 to 10 GHz

RF Amplifier  from RFHIC

The RRT901005K0-57 from RFHIC is an X-Band Transmitter that operates from 9 to 10 GHz. It delivers a pulsed output power of more than 5 kW with a gain of 57 dB. The amplifier has a duty cycle of up to 10%, a pulse width range from 1 to 100 us, and a rise/fall time of less than 100 ns. It has a VSWR of under 2:1. The transmitter uses high efficiency GaN transistors to replace industrial magnetrons and other vacuum tubes that are currently used in high power applications.
Download Datasheet | Product Details
RF Amplifier
2 W Solid State Low Noise Power Amplifier from 41 to 47 GHz

RF Amplifier  from Exodus Advanced Communications

The MPA3021 from Exodus Advanced Communications is a GaAs FET Hybrid Solid State Low Noise Power Amplifier that operates from 41 to 47 GHz. This class AB linear amplifier delivers over 2 W of saturated output power (P1dB of 1 W) with a gain of more than 33 dB. It has spurious of up to -60 dBc, and harmonics of up to -20 dBc. The amplifier has built-in protection circuits and requires an external heat sink for cooling.
Download Datasheet | Product Details
RF Amplifier
1000 W Magnetron Driver Amplifier from 2900 to 3500 MHz

RF Amplifier  from Empower RF

The 2239 from Empower RF Systems is a Solid-State Class AB Pulsed Power Amplifier System that operates from 2900 to 3500 MHz. This amplifier is available in a compact 3U rack compatible footprint with features ideal for integrating into Magnetron, Klystron, and TWT systems. It delivers 1000 W of peak pulsed output power and has a gain of more than 65 dB.
Download Datasheet | Product Details
RF Connector
40 GHz Hermetic Waterproof 2.4 mm Connectors

RF Connector  from MegaPhase

The Hermetic Waterproof Connectors from Megaphase are 2.4 mm Connectors that operate up to 40 GHz. They offer a compact connector interface with the ability to withstand rain, 100% condensation, and water submersion up to a depth of 1m. They have low loss and excellent phase stability that ensures reliable performance which is required for extreme applications in severe environments including ground, sea, and airborne applications.
Download Datasheet | Product Details
RF Cable Assembly
4.3-10 RF Cable Assembly from DC to 6 GHz

RF Cable Assembly  from TE Connectivity

The 2081976-1 from TE Connectivity is an RF Cable Assembly that can be used from DC to 6 GHz. This 1/2" Superflex coaxial cable has a Polyethylene jacket and measures 1 m in length. The cable assembly can handle up to 500 W of power at 2 GHz and has a return loss of less than 1.06 dB. It is available with 50 ohm 4.3-10 connectors on either end.
Download Datasheet | Product Details
Voltage Controlled Oscillator
Quadband VCO GaAs MMIC from 11.9 to 18.3 GHz

Voltage Controlled Oscillator  from Analog Devices

The HMC8362 from Analog Devices is a Quadband Voltage Controlled Oscillator (VCO) that integrates four independent, narrow-band VCOs with overlapping frequency bands to provide an operating frequency from 11.9 to 18.3 GHz. It is designed to offer wideband capabilities without compromising on phase noise performance and includes resonators, negative resistance devices, and varactor diodes.
Download Datasheet | Product Details
Directional Coupler
30 dB Directional Coupler from 2 to 40 GHz

Directional Coupler  from VidaRF

The VDC-20400A30 from VidaRF is a broadband directional coupler that operates from 2 to 40 GHz. The coupler provides coupling of 30 dB with a directivity of over 10 dB and an insertion loss of less than 1.6 dB. It can handle more than 20 watts of input power and is available in a lead-free housing with 2.92 mm female connectors.
Download Datasheet | Product Details
Sponsored by CRFS
 
 
 
Down Converter
50 GHz Heterodyne Downconversion System for Phase Noise Measurements

Down Converter  from Holzworth Instrumentation

The HA7063A from Holzworth is a Heterodyne Downconversion System that can accept an input RF signal from 10 MHz to 50 GHz. This system has been designed to seamlessly integrate with Holzworth's HA7062 series real-time phase noise analysis products as an ANSI z540 calibrated frequency extension. It downconverts the signal to DC to 40 MHz (with HA7062C) and DC to 100 MHz (with HA7062D).
Download Datasheet | Product Details
RF Module
Wi-Fi (2.4 and 5 GHz) + Bluetooth 5.0 Combo Module for Automotive Applications

RF Module  from Cypress Semiconductor

The CYW89373 from Cypress is an Automotive Wi-Fi + Bluetooth Combo module that supports 802.11 a/b/g/n/ac Wi-Fi specifications and Bluetooth 5.0 (BR + BLE + EDR). It features Cypress's Real Simultaneous Dual Band (RSDB) solution that provides simultaneous Wi-Fi operation in both 2.4 GHz and 5 GHz bands with a single-MAC architecture supporting 1x1 SISO operation and provides a data rate of up to 433 Mbps.
Download Datasheet | Product Details
GNSS Module
GNSS SoC for Battery-Powered Asset Tracking Devices

GNSS Module  from u-blox AG

The UBX-M10050-KB from u-blox is an L1-Band GNSS Receiver IC that is designed for battery-powered asset tracking devices. It supports concurrent reception of four GNSS constellations - GPS, GLONASS, Galileo, and BeiDou and provides exceptional sensitivity and acquisition time. This chip has a TTFF cold start of less than 24 s and a TTFF hot start under 1 sec.
Download Datasheet | Product Details
RF Module
Bluetooth Low Energy (v5.0) Module for IoT Devices

RF Module  from TAIYO YUDEN (U.S.A.) Inc

The EYSKJNAWB-WX from Taiyo Yuden is a Bluetooth Low Energy (v5.0) Module that operates from 2402 to 2480 MHz. It supports 2M / 1M / 125 kbps data rates. The module provides an output power of +8 dBm and requires a DC voltage from 1.7 to 3.6 V. It has an ARM Cortex M4 32-bit processor that has 512KB of flash memory and 128KB of RAM.
Download Datasheet | Product Details
RF Module
Ultra-low Power LoRaWAN IoT Module

RF Module  from Miromico

The new FMLR-1110-x-STL0Z from Miromico is an ultra-low-power IoT platform-in-a-module that integrates a long-range LoRa® transceiver, wireless scanners for multi-constellation GPS/GNSS, and passive Wi-Fi AP MAC addresses targeting asset management applications. It has an integrated ARM Cortex-M0+ 32-bit microcontroller that runs the entire RF stack and has sufficient resources available to run user applications.
Download Datasheet | Product Details
Microwave Backhaul Radio Links
26 / 29 / 31 GHz Point-to-Multipoint Microwave Backhaul Radio

Microwave Backhaul Radio Links  from Cambridge Broadband Networks Group

The VectaStar 600 Flex from Cambridge Broadband Networks is a Point-to-Multipoint Microwave Platform for small cell backhauls, enterprise access, and ISP networks. It has a small form factor and operates in the ETSI 26 GHz band & FCC 29/31GHz LMDS A2/A3 bands. The VS600 Flex is available with 30 or 90 degree sector antennas and has a capacity of up to 620 Mbps per link, up to 1.6 Gbps per sector, and up to 19.2 Gbps per hub site.
Download Datasheet | Product Details
RF Variable Attenuator
63.5 dB Programmable Step Attenuator from 0.1 to 18 GHz

RF Variable Attenuator  from JFW Industries

The Model 50P-2101 from JFW Industries is a Solid-State Programmable Attenuator that operates from 0.1 to 18 GHz. It has seven individually controlled attenuation steps: 0.5 dB, 1 dB, 2 dB, 4 dB, 8 dB, 16 dB and 32 dB to cover a total attenuation range from 0 to 63.5 dB. The attenuator operates bi-directionally and can handle up to 24 dBm of power at the input port and 15 dBm of power at the output port.
Download Datasheet | Product Details
RF Shielded Test Enclosure
RF Shielded Test Enclosure for 802.11 a/b/g/n/ac, Bluetooth, RFID and 3G Device Testing

RF Shielded Test Enclosure  from RF Electronics

The HDRF-2124-T from RF Electronics is a RF Shielded Test Enclosure that operates from 20 MHz to 6 GHz. It has a thick RF absorbing foam that provides an isolation of more than 90 dB. It has shielded power filters for providing power connection in the box while blocking all wireless signals. The HDRF-2124-T has a number of I/O connector options that include HDMI, RJ45, USB, DB9, VGA, DB25 and AC/DC.
Download Datasheet | Product Details
Clock Oscillator
Simple Package Clock Oscillator from 10 to 50 MHz

Clock Oscillator  from IQD Frequency Products

The IQXO-951-25TS from IQD is a Simple Package Crystal Oscillator (SPXO) that operates from 10 to 50 MHz. The oscillator has a tight frequency stability of ±10 to ±20 ppm over the operating temperature range from -40 to 85° C. It has a duty cycle of 45/55% and provides a CMOS output logic. The oscillator requires a supply voltage from 1.62 to 3.63 V and consumes up to 15 mA of current.
Download Datasheet | Product Details
RFID Tag
Eco-Friendly HF NFC Tag for IoT Applications

RFID Tag  from Identive

The I00XXXN39A25 from Identiv is an Eco-Friendly HF NFC Tag with a 13.56 MHz smart inlay. It has a user memory of 48 bytes, an EPC memory size of 64 bytes, and is based on the NXP NTAG210µ IC. The tag is manufactured on renewable paper, without plastic layers and harmful chemicals, and has one of the lowest carbon footprints in the industry.
Download Datasheet | Product Details
About everything RF
everything RF keeps users up to date with the RF & Microwave Industry. We provide the latest news, information on new product releases, upcoming events, articles, white papers, interviews and much more.
To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]