| New RF and Microwave Products this Week . |
|
|
| USB-Powered 2-Channel PLL Frequency Synthesizer from 45 MHz to 22.6 GHz | |
Frequency Synthesizer
from Z-COMM
|
| The SSG22645LX from Z-Communications is a Smart PLL Frequency Synthesizer that generates frequencies from 45 MHz to 22.6 GHz. It has two independently-controlled output channels with a power range from -20 to +7dB and a phase noise of -117 dBc/Hz (@100 kHz offset). This synthesizer has 3 frequency sweep modes – single sweep, repeat sweep (continuous), and cycle sweep – each with frequency start/stop, step size, and dwell time. |
| |
Download Datasheet
Product Details | |
|
|
|
| GaAs pHEMT Low Noise Amplifier MMIC from 1 to 22 GHz | |
RF Amplifier
from Analog Devices
|
| The ADL8102 from Analog Devices is a Low Noise Amplifier MMIC that operates from 1 to 22 GHz. It delivers a gain of 27 dB with a noise figure of 3 dB and has a saturated output power of 15.5 dBm. This GaAs pHEMT amplifier requires a DC supply of 5 V and consumes less than 110 mA of current. It is ideal for telecommunications, satellite communications, military radar, weather radar, civil radar, and electronic warfare applications. |
| |
Download Datasheet
Product Details | |
|
|
|
| Double-balanced Mixer from 18 to 50 GHz | |
RF Mixer
from ERZIA
|
| The ERZ-MIX-1800-5000-10 from ERZIA is a Double-Balanced Mixer with an RF/LO frequency from 18 to 50 GHz and an IF Frequency from DC to 20 GHz. It has a conversion loss of 10 dB and an LO drive power of 16 dBm. This mixer can handle an input power of up to 21 dBm and provides a LO-to-IF and RF-to IF-isolation of 35 dB. |
| |
Download Datasheet
Product Details | |
|
|
|
| 1 W, 50-Ohm mmWave RF Termination from DC to 110 GHz | |
Termination
from Marki Microwave
|
| The TF50-110M from Marki Microwave is an RF Termination that operates from DC to 110 GHz. It can handle an input power of up to 1 W and has a return loss of 20 dB over the entire band. This 50-ohm termination utilizes passive GaAs MMIC technology to enable the production of smaller constructions that replace larger form factor circuit board constructions. |
| |
Download Datasheet
Product Details | |
|
|
|
| 0.5 W, 50-Ohm AlN Surface-Mount Termination from DC to 6 GHz | |
Termination
from TTM Technologies
|
| The C05N50Z4 from Anaren is an RF Termination that operates from DC to 6 GHz. It can handle an input power of 0.5 W and has a return loss of better than 20 dB. This termination is manufactured using an Aluminum Nitride (AlN) ceramic substrate and utilizes a non-Nichrome thick film resistive element. It is ideal for terminating high-power 90° couplers and microstrip circuits. |
| |
Download Datasheet
Product Details | |
|
|
|
| Compact Spectrum Analyzer and Measuring Receiver from 100 kHz to 12.4 GHz | |
RF Spectrum Analyzer
from Signal Hound
|
| The USB-SA124B Spectrum Analyzer and Measuring Receiver from Signal Hound that operates from 100 kHz to 12.4 GHz. This USB powered compact analyzer is ideal for general field and lab use, electrical engineering students, ham radio enthusiasts, and electronic hobbyists. It has a wide dynamic range from -151 dBm to 10 dBm and can also be used as a down-converter with a 63 MHz IF Output and a 6 MHz Resolution Bandwidth. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
| 2-Port USB Controlled Lab Grade VNA from 300 kHz to 6.5 GHz | |
Vector Network Analyzer
from Copper Mountain Technologies
|
| The SC5065 from Copper Mountain Technologies is a modular 2-port compact lab-grade VNA that operates from 300 kHz to 6.5 GHz. This small USB Controlled lab grade VNA has higher speeds, more dynamic range, and higher output power, with features like time domain and gating conversion, segmented frequency sweeps, linear/ logarithmic sweeps, power sweeps, multiple trace formats, 16 channels max. with up to 16 traces each, marker math, and limit tests. |
| |
Download Datasheet
Product Details | |
|
|
|
| Spectrum Monitoring and Geolocation System from 9 kHz to 8 GHz | |
RF Spectrum Analyzer
from CRFS
|
| The Node 100-8 from CRFS is a Spectrum Monitoring and Geolocation System that operates from 9 kHz to 8 GHz. It has been developed for remote deployment in distributed networks both indoors and outdoors, including in hostile environments. This Intelligent Wideband Receiver is available in a compact, rugged and weatherproof housing, it has been optimized for size, weight and power (SWaP) and is simple to connect to power and network. It has an instantaneous bandwidth of 100 MHz and a tuning resolution of 1 Hz. |
| |
Download Datasheet
Product Details | |
|
|
|
| 10 MHz to 26 GHz Real-Time Phase Noise Analyzer | |
Phase Noise Analyzer
from Holzworth Instrumentation
|
| The HA7062D from Holzworth is a real time phase noise analysis system that operates from 10 MHz to 26 GHz (optional to 40 GHz). It has a real-time engine that covers the full measurement bandwidth with extremely fast measurement speeds to reduce product development time and optimize ATE manufacturing throughput. Holzworth has architected the instrument’s front end so that the noise floor limits can actually be measured. |
| |
Download Datasheet
Product Details | |
|
|
|
| Flexible Microwave Cable Assembly from DC to 40 GHz | |
RF Cable Assembly
from HUBER+SUHNER
|
| The SUCOFLEX 540E from HUBER+SUHNER is a High-Flexibility Microwave Cable Assembly that operates from DC to 40 GHz. It is available with 2.9 mm or 2.4 mm connectors and is designed to provide an ideal solution for precise measurements in critical laboratory conditions. This 50-ohm cable assembly delivers high phase and amplitude stability with flexure and movement and has a unique design that ensures zero spring back and facilitates efficient handling during measurement. |
| |
Download Datasheet
Product Details | |
|
|
|
| 24-Channel High-Density SMPM for Cryogenic Applications from DC to 40 GHz | |
RF Cable Assembly
from IntelliConnect
|
| The C446-ZZZ-101G from IntelliConnect is a 24-Channel High-Density SMPM Cable Assembly that operates from DC to 40 GHz. This cryogenic interconnect solution has 24 channels where each set of connectors are connected using a 0.47-inch semi-rigid conformance cable. This assembly has a durability of more than 100 mating cycles and meets the MIL-STD-348 and MIL-PRF-39012 standards. The number of channels can be customized based on requirement. |
| |
Download Datasheet
Product Details | |
|
|
|
| 110 GHz RF Cables with 1.63 mm Outer Diameter | |
RF Cable
from Insulated Wire
|
| The 047 Series from Insulated Wire are RF Cables that operate up to 110 GHz. They provide a shielding effectiveness of more than 90 dB (up to 18 GHz), have a velocity of propagation of 71%, and have a time delay of 1.43 ns/ft. These cables have a static bend radius of 5.1 mm and a dynamic bend radius of 9.5 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
| Ultra-Low Jitter Crystal Oscillator from 20 to 50 MHz | |
XO
from Dynamic Engineers
|
| The XO3225BL-ULJ_CMOS from Dynamic Engineers is a Crystal Oscillator that operates from 20 to 50 MHz. It has frequency stability (versus temperature) of ±25 ppm, phase noise of -166 dBc/Hz (@1 MHz offset), and ultra-low jitter of 48 fs (RMS). This oscillator has a start-up time of 0.8 ms and a rise/fall time of less than 5 ns. |
| |
Download Datasheet
Product Details | |
|
|
|
| 8.5 kW GaN Pulsed Transmitter System from 5.6 to 5.7 GHz | |
Microwave Generator
from RFHIC
|
| The RRK56578K5-790 from RFHIC is a Solid-State Transmitter System that operates from 5.6 to 5.7 GHz. It delivers a pulsed output power of 8.5 kW with a power gain of 79% (up to 10% duty cycle and pulse width from 1 to 100 µs). This system uses GaN transistors and is suitable for upgrading the existing VED (Vacuum Electronic Device, such as Klystron, Magnetron, Travelling Wave Tube, and Cross Field Amplifier) based transmitters for radar platforms. |
| |
Download Datasheet
Product Details | |
|
|
|
| 750 W Solid State Amplifier System from 1 to 6 GHz | |
RF Amplifier
from AR RF/Microwave Instrumentation
|
| The 750S1G6C from AR RF/Microwave Instrumentation is a Solid-State Amplifier System that operates from 1 to 6 GHz. This class A amplifier delivers a saturated output power of more than 750 W from 1 to 4.2 GHz and 500 W from 4.2 to 6 GHz. It is immune to input overdrive above 0 dBm (up to 13 dBm), power supply faults, over-temperature, and has protection against other failure conditions as well. |
| |
Download Datasheet
Product Details | |
|
|
|
| Surface-Mount Gain Block from 50 to 5000 MHz | |
RF Amplifier
from Guerrilla RF
|
| The GRF2040 from Guerrilla RF is a Gain Block that operates from 50 to 5000 MHz. It provides a gain of 10.2 dB with a noise figure of 3.1 dB and has an integrated bypass mode. This gain block requires a DC supply from 2.7 to 8 V and consumes less than 90 mA of current. It is internally matched to 50 ohms at the input and output ports, needing only external DC blocks and a bias choke on the output. |
| |
Download Datasheet
Product Details | |
|
|
|
| GaAs Thru-Line MMIC Filter from DC to 40 GHz | |
Band Pass Filter
from AmpliTech
|
| The AGM-005 from AmpliTech is a GaAs Thru Line MMIC Filter that operates from DC to 40 GHz. It can handle an input power of up to 20 dBm, has a passband insertion loss of less than 0.26 dB, and a maximum passband return loss of 15 dB. This thru line Filter is available as a die that measures 1.00 x 0.75 x 0.10 mm and has 50 ohm matched DC coupled RF ports. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low Loss Cryogenic Circulator from 0.9 to 1.1 GHz | |
RF & Microwave Circulator
from Low Noise Factory
|
| The LNF-CIC0.9_1.1A from Low Noise Factory is a Cryogenic Circulator that operates from 0.9 to 1.1 GHz. It has been designed to meet the strict requirements of ultra-low temperature physics research. This circulator has gold plated OFHC copper body that ensures minimum loss and that this loss reaches the lowest possible temperature to minimize thermal noise. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Multiband 2-Way Power Splitter from 340 to 3800 MHz | |
Power Divider
from CommScope
|
| The S-2-TCPUSEW-H-NI6 from CommScope is a Multiband 2-Way Power Splitter that operates from 340 to 3800 MHz. It can handle an average input power of up to 300 W and a peak input power of 3 kW. This power splitter has an insertion loss of 0.3 dB, a split loss of 3 dB, a VSWR of 1.25:1 and is available in a module that measures 286 x 61 x 25 mm with N-type (female) connectors. It is ideal for wireless infrastructure applications. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
|
|
|
| 3GPP Rel-14-Based LTE Cat 1 bis Module for LTE-FDD/LTE-TDD Coverage | |
Cellular Module
from Quectel
|
| The EG916Q-GL from Quectel is an LTE Cat 1 bis Module for LTE-FDD & LTE-TDD coverage and supports DFOTA & Wi-Fi Scan features. It is based on 3GPP Rel-14 LTE technology and delivers a downlink data rate of 10 Mbps and an uplink data rate of 5 Mbps. This module is compatible with Quectel LPWA BG95 series and BG96 modules and LTE Standard EG91 series, EG95 series, and EG915Q-NA modules. |
| |
Download Datasheet
Product Details | |
|
|
|
| Sub-6 GHz 5G-NR Module for Middle East and Africa Markets | |
Cellular Module
from Fibocom
|
| The FG360-MEA from Fibocom is a 5G-NR Sub-6 GHz Module that has been designed for the Middle Eastern and African markets. It supports both 5G standalone (SA) and non-standalone (NSA) network architectures, delivering enhanced transmission speed, greater carrying capacity, and reduced network latency for homes, businesses, and mobile users. |
| |
Download Datasheet
Product Details | |
|
