PREV 20th June, 2018 NEXT

New RF & Microwave Products this Week

20 June, 2018 - everything RF Newsletter
 
everything RF
Date: 20 June, 2018
 
Sponsored by Rohde & Schwarz
 
 
 
New RF & Microwave Products this Week
Front End Module
Switch + LNA Module for 5G Massive MIMO Base Stations

Front End Module from pSemi

The PE53111 from pSemi is a switch + LNA module that operate from 2.3 to 2.7 GHz. The module has an on-chip, fail-safe switch that can handle an average input power of up to 5W. The modules support sub-6 GHz 5G new radio (NR) bands and meets the stringent RF system requirements of massive MIMO base stations.
 
Download Datasheet | Product Details
 
RF Amplifier
71 to 76 GHz E-band Power Amplifier for Point to Point Radios

RF Amplifier from Filtronic

Cerus from Filtronic is an E-band Power Amplifier that operates from 71 to 76 GHz. This amplifier has been developed for high capacity E-band point-to-point radios. It provides an output power of up to 35 dBm with a small signal gain of under 18 dB. The amplifier requires a supply of 4V while consuming up to 10 A of current.
 
Download Datasheet | Product Details
 
Gain Equalizer
DC to 6 GHz Gain Equalizer MMIC

Gain Equalizer from Mini Circuits

The EQY-10-63+ from Mini-Circuits is a Gain Equalizer that operates from DC to 6 GHz. This absorptive gain equalizer is fabricated using the highly repetitive GaAs IPD MMIC process incorporating resistors, capacitors and inductors having negative insertion loss slope. It has a nominal attenuation slope of 10.2 dB and can handle an input power of up to 32 dBm.
 
Download Datasheet | Product Details
 
RF Amplifier
0.7 to 6 GHz, 50 Watt Hybrid Power Amplifier Module

RF Amplifier from AR RF/Microwave Instrumentation

The 50HM1G6-47 from AR RF/Microwave Instrumentation is a compact, wideband, hybrid power amplifier module that operates from 0.7 to 6 GHz. It provides a small signal gain of 55 dB with excellent gain flatness, noise figure of 8.5 dB and low intermodulation distortion. When used with a sweep generator, it provides an RF power of more than 50 Watts while operating from a single DC supply voltage of 28V.
 
Download Datasheet | Product Details
 
Band Pass Filter
Low Cost Custom RF Filter from 300 MHz to 2.4 GHz

Band Pass Filter from NuWaves Engineering

The µFILTER from NuWaves is a low-cost miniature RF filter designed to allow the end user the capability to select a custom filter (Bandpass, Highpass, Low-Pass, or Band-Reject). The custom band-pass filter can be fine tuned to have any frequency requirement from 300 MHz to 2.4 GHz with 3 dB bandwidth from 1% to 40%. The filter is available in a module with standard SMA connectors.
 
Download Datasheet | Product Details
 
Directional Coupler
Surface Mount Directional Coupler from 500 to 3000 MHz

Directional Coupler from Innovative Power Products

The IPP-8090 from Innovative Power Products is a surface mount directional coupler that operates from 500 to 3000 MHz. It has a coupling value of 36 dB and can handle up to 200 watts of power. The coupler has an insertion loss of less than 0.3 dB and directivity of more than 17 dB. It is available is a surface mount package that measures 1 x 1 inches.
 
Download Datasheet | Product Details
 
Termination
2 Watt TNC-Male Termination from DC to 6 GHz

Termination from MECA

The 401-5 Termination from MECA operate from DC to 6 GHz. This TNC-male termination can handle up to 2 watts of average power and 1.5 KW of peak power. It is matched to 50 ohms and has a VSWR of 1.25:1. The termination measures 1.35 inches in length.
 
Download Datasheet | Product Details
 
RF Amplifier
E-Band Power Amplifier from 60 to 90 GHz

RF Amplifier from SAGE Millimeter

The SBP-6039032012-1212-E1 from SAGE Millimeter is a power amplifier that operates from 60 to 90 GHz in the E-band. It provides a saturated output power of 16 dBm with a gain of 20 dB. The amplifier requires a supply voltage of 8 VDC and consumes 250 mA of current. It is available in a module that measures 1.10 x 1.50 x 0.75 inches and is ideal for radar systems, communication systems and test equipment.
 
Download Datasheet | Product Details
 
Limiter
8 to 12 GHz, X-band Coaxial Limiter

Limiter from Cobham Signal & Control Solutions

The ACLM5022C110 from Cobham is a X-band coaxial limiter that operates from 8 to 12 GHz. It can handle up to 25 Watts of CW power over the full temperature range from -55°C up to 85°C. The limiter has a flat leakage of below 15 dBm and a recovery time of 200 nsec. When operating in a small signal environment, insertion loss is less than 1.5 dB and VSWR is less than 1.5:1. It is available in a compact module with field replaceable SMA connectors.
 
Product Details
 
Power Divider
2 Way Divider/Combiner from 0.5 GHz to 7 GHz

Power Divider from BBTLine

This is a patented (U.S. Patent 9,570,792) 2 Way Divider/Combiner from BBTLine that operates from 0.5 GHz to 7 GHz and can handle up to 20 watts of power. It has an insertion loss of less than 0.9 dB and provides over 15 dB of isolation. The divider is available in a module with SMP Smooth-Bore connectors.
 
Download Datasheet | Product Details
 
Power Sensor
50 MHz to 6 GHz Power Sensor Controlled via LAN

Power Sensor from Rohde & Schwarz

The NRQ6 from Rohde & Schwarz is a Frequency Selective Power Sensor that operates from 50 MHz to 6 GHz. It has a dynamic range from -130 dBm to +20 dBm and a measurement bandwidth of 100 MHz. The sensor can perform band-limited power measurements - i.e. power measurements on a selected transmission channel, down to -130 dBm.
 
Download Datasheet | Product Details
 
RF Mixer
0.1 to 5.0 GHz Up/Down-converter Mixer with Integrated LO Buffer

RF Mixer from Guerrilla RF

The GRF7001 from Guerrilla RF is a high linearity mixer with integrated LO buffer. The mixer has an RF/IF frequency range of the mixer is 0.1 to 5.0 GHz, and the LO range is 0.1 to 4.0 GHz. It has low conversion loss and can be used as an up or down converter. The GRF7001 inputs and outputs are single-ended and internally matched to 50 ohms.
 
Product Details
 
Band Pass Filter
5.2 GHz Co-Existence BAW RF Filter for Wi-Fi Applications

Band Pass Filter from Akoustis

The AKF-1252 from Akoustis is a 5.2 GHz co-existence BAW RF filter for Wi-Fi applications. Covering both U-NII-1 and U-NII-2A pass-bands, it delivers a low insertion loss of under 2 dB with a high rejection of over 50 dB and can handle an input power of up to 32 dBm. The filter is available in an ultra-small module that measures 2 x 2.5 x 0.9 mm and operates over a temperature range of -40 to 85 degree Celsius.
 
Product Details
 
Laminate
Low Loss High Impedance Laminates

Laminate from Rogers Corporation

The MAGTREX 555 from Rogers are high impedance laminates that enable antenna designers to miniaturize VHF and UHF antennas while maintaining the bandwidth achieved in a larger design. These laminates feature a closely matched X/Y axis permeability and permittivity of six and six and a half respectively, along with low magnetic and dielectric loss below 500 MHz.
 
Download Datasheet | Product Details
 
Cellular Module
Cat M1/NB1 devices for IoT Applications

Cellular Module from Telit Communications

The ME910C1 Series from Telit are Cat M1/NB1 devices that have been specifically developed for IoT applications. They have a maximum downlink and uplink data rate in the range of 300 kbps. The ME910C1 is a member of Telit&rsquos flagship xE910 module family delivering 4G radio access technology in the 28.2 x 28.2 x 2.2 mm family form factor.
 
Download Datasheet | Product Details
 
Sponsored by Rohde & Schwarz
Rohde & Schwarz
FREE Webinar: Demystifying 5G - 5G NR Physical Layer
This webinar provides an overview of the latest 5G NR physical layer specification, discusses the test challenges related to 5G and demonstrates practical test solutions. The webinar concludes with a look at the challenges involved in SA operation. Click here to learn more.
 
 
 
Fixed Attenuator
100 Watt Fixed Attenuator from DC to 3 GHz

Fixed Attenuator from JFW Industries

The Model 50FHLB-xxx-100 from JFW Industries is a uni-directional 100 Watt fixed attenuator that operates DC to 3 GHz. It is available with an attenuation range of 10, 20 or 30 dB. The attenuator has an integrated heatsink that is only 2.25 inches in diameter and has coaxial RF connectors (N, 4.3/10, or 7/16) matched to 50 ohms.
 
Download Datasheet | Product Details
 
Wireless SoC
Dual Wi-Fi, Dual-mode Bluetooth 5/BLE, and 802.11p Automotive Wireless SoCs

Wireless SoC from Marvell

The 88Q9098x family of SoCs from Marvell is the industry’s first 802.11ax solution with 2x2 plus 2x2 concurrent dual Wi-Fi, dual-mode Bluetooth 5/BLE and 802.11p for connected vehicles. The innovative concurrent dual Wi-Fi architecture sets a new technology precedent, integrating two complete Wi-Fi subsystems into a single SoC, and enabling two independent 2x2 data streams to run concurrently and at full throughput.
 
Download Datasheet | Product Details
 
Antenna
4.9 to 6 GHz Multi-Polarized Outdoor MIMO Antenna

Antenna from MP Antenna

The 08-ANT-0937 from MP Antenna is a is a low profile Multi-Polarized outdoor MIMO antenna for mobile data communications that operates from 4.9 to 6 GHz. It is available with 1, 2, 3, or 4 separate antenna feeds allowing maximum diversity for 4.9 GHz / 5.8 GHz WiFi and WiMAX broadband wireless frequencies. The antenna provides a gain of 4 dBi and can handle a power of up to 50 watts.
 
Download Datasheet | Product Details
 
Sponsored by Rohde & Schwarz
 
 
 
About everything RF
everything RF is the largest database of RF & Microwave products. We have listed complete product catalogs from over 1,000 manufacturers and made their products searchable using our specially developed parametric search tool.

To unsubscribe please click here[Sender_Name]
[Sender_Address], [Sender_City], [Sender_State], [Sender_Zip]